Regency e18 gas insert owners & installation manual (76 pages)
Summary of Contents for Regency Z2510L
Page 1
Owners & WarmHearth Fireplace Installation Manual Regency WarmHearth High Efficiency EPA Certified Fireplace MODEL: Z2510L Tested by: Installer: Please complete the details on the back cover and leave this manual with the homeowner. Homeowner: Please keep these instructions for future reference.
Page 2
Thank-you for purchasing a REGENCY FIREPLACE PRODUCT. The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. This product has been certified by the Environmental Protection Agency of the United States. This means that it meets the strictest standards in providing you with the latest in clean burning technology and efficiency.
We have printed a copy of the contents here for your review. Copy of Safety Label for Z2510L NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
INSTALLATION READ BEFORE YOU INSTALL THE REGENCY WARMHEARTH HIGH EFFICIENCY EPA CERTIFIED FIREPLACE This installation manual will enable you to make a safe, efficient and dependable installation of your fireplace and chimney system. Please read and understand these instructions before beginning your installation.
FAILURE TO USE PARTS MANU- FACTURED BY REGENCY FIRE- PLACE INDUSTRIES OR VARIA- TIONS IN TECHNIQUES AND CON- STRUCTION MATERIAL DESCRIBED IN THIS MANUAL MAY CREATE A FIRE HAZARD AND VOID REGEN- CY’S WARRANTY. The WarmHearth main unit consists of the following: 1) The main fire box and heat exchanger 2) The large door with ceramic glass...
INSTALLATION Note: If the fireplace is being cantilev- ered through an outside wall, the entire enclosure (floor, wall and false ceiling) up to the first ceiling level must be completely insulat- ed and vapor sealed and sheathed, to avoid transfer of cold air through the fireplace when not in use.
support as well as the floor beneath the hearth extension. Note: The “Z” type safety strip is not supplied by Regency and must be fabricated locally. 2) Refer to fireplace drawing and specifica- tions on page 6 and page 7 for framing dimensions and details.
INSTALLATION BEFORE YOU START Check your inventory list to be sure you have all the necessary parts supplied in good usable condition. Check for any concealed damage. Check the operation of the combustion air damper. When the damper is in the fully closed position, the damper handle should be to the right. When damper is in the fully open position, the damper handle must be in the left position.
result if stand-offs are not properly installed. IMPORTANT: Insulation extends for- ward to seal against the back of the WarmHearth masonry or non-com- bustible face. SET THE WARMHEARTH INTO POSITION 1) Estimate the total weight of the fireplace system and surround materials such as brick, stone, etc., to be installed.
INSTALLING THE OUTSIDE AIR KIT Combustion air is fed to the firebox through a connection on the rear lower left side of the unit. A free flowing supply of air must be available to this opening at all times. Combustion air may be taken from inside the building if the local building code allows, but performance may suffer.
INSTALLATION OPTION 2 External Blower with Thermo-Disc The thermodisc allows the fireplace to warm up properly before the blower will switch on. The blower is also switched off if the fireplace temperature falls below suitable heating levels. OPTION 3 Internal and External Blowers with a Thermodisc When both blowers are used the thermodisc should be connected to the external blower.
5) Install the connector collar into the unit making sure it is pushed all the way down. Reach through the upper louver opening and snip and bend out the lower edge of the collar in at least 4 places inside the fireplace with pliers so it can't be pulled out.
Page 16
INSTALLATION be at the top so they lie flat. Bend out the lower edge of the valve at 4 places inside the fireplace with pliers so that it can't be pulled out again. Diagram 2. Diagram 1 Diagram 2 5) Locate the blower in a convenient location near the fireplace.
FINISHING THE WARMHEARTH Completing the Facing Facing materials must be thin veneer (non-self supporting facades) or self supporting facades. If you are installing a thin veneer facade the Regency Masonry Retainer Kit (Part # 000-920) is recommended. All facades must be Non- Combustible such as brick, rock or ceramic tile.
INSTALLATION 4) Place side metal filler strips in between stove and framing to cover the stand-off space. Fit the strips behind "A" so that they cover the stand-offs, and will prevent mor- tar from falling through the mesh. 5) Center door arch edge, mark and drill holes. Note the top of the side pieces meet up with the edges of the center arch.
MASONRY LINER/ BRICKS Insulated refractory panels are included to extend the life of the fireplace and help radiate heat more evenly. Make sure Insulating Paper is in place along the bottom, side and rear before bricks are put into place. Insulation batt, 1 in.
MAINTENANCE CAUTION: Never leave unit unat- tended if door is left open. This procedure is for fire start-up only, as unit may overheat if door is left open for too long. The door is to be opened for a maximum of 5 min- utes while loading or for ignition purposes only.
WARRANTY Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit thoroughly before it leaves our door. Regency Industries Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a Regency Product.
Page 24
Regency fireplace products are designed with reliability and simplicity in mind. In addition, our internal Quality Assur- ance Team carefully inspects each unit thoroughly before it leaves our door. Fireplace Products Internation- al Ltd. is pleased to extend this Limited Lifetime Warranty to the original purchaser of a Regency Product.