Advertisement
Quick Links
PLAYING A DISC
This user manual explains the basic
accompanying the specific DVD in question
instructions for operating this unit. Some
for more information about the options
DVDs are produced in a manner that allows
available on that DVD.
specific or limited operation during playback.
may appear on the screen during
Therefore, this unit may not respond to all
operation. It means that the desired operation
operating commands.
THIS IS NOT A
is not permitted by the unit or disc.
DEFECT. Please refer to the instructions
Playing a Disc
Audio Selection
1. Press the STANDBY / ON button to turn on
On some DVDs, the sound is recorded in two
the unit.
or more formats. Follow the directions below
See CUSTOMIZING THE FUNCTION
to select the preferred language and sound
SETTINGS before proceeding to step 2.
system.
OPEN/CLOSE button to open
1. While a disc is playing, press the AUDIO
2. Press the
the disc tray.
button to show the current audio format
3. Place a disc onto the disc tray with the
number. e.g.
label side up.
OPEN/CLOSE button to close
4. Press the
the disc tray. It takes a short while for your
2. Press the AUDIO button repeatedly to
unit to load the disc. After loading, for most
DVDs, the unit will automatically take you
select the desired audio format.
main menu or start playing.
Notes:
5. If the unit does not automatically start
• If only one audio format is recorded on the
PLAY
playing the DVD, press the
DVD, the number does not change.
button.
• Some DVDs allow you to change audio
selections only via the disc menu. If this
is the case, press the MENU button and
Pausing Playback (Still Mode)
choose the appropriate language on the
Press the
PAUSE button on the remote. To
disc menu.
resume normal playback, press the
PLAY
• You can select different audio channels
button.
(Stereo, Mono L, Mono R or Mix Mono)
PAUSE button, the
Each time you press the
on an Audio CD by pressing the AUDIO
picture advances one frame.
button repeatedly.
Stopping Playback
Subtitle Selection
• Press the
STOP button at the location
1. While a DVD is playing, press the
where you want to interrupt playback. To
SUBTITLE button to display the current
resume playback at the position where
language
setting,
as
shown
in
the
PLAY
the disc was stopped, press the
example.
button.
• If you press the
STOP button twice, the
unit’s memory will be cleared and pressing
2. Press the SUBTITLE button repeatedly to
PLAY button will reset the disc to
the
select the desired subtitle language.
the beginning.
Notes:
• Some DVDs are set to display subtitles
Fast Forward / Fast Reverse
automatically, and you cannot turn them
1. Press the SEARCH
or SEARCH
off even if you set the subtitle function to
button when a disc is playing. Each time
off.
you press the SEARCH
or SEARCH
• During some scenes, the subtitles may not
button, the playback speed changes in
appear immediately after you select your
the following sequence:
desired scene.
• The number of subtitle languages recorded
differs depending on the disc. If only one
PLAY
FORWARD x2
FORWARD x4
language is recorded, the language does
not change.
FORWARD x20
FORWARD x8
• This function can only be used for discs
or
on which subtitles have been recorded in
PLAY
BACKWARD x2
BACKWARD x4
multiple languages.
• Some DVDs allow you to change subtitles
BACKWARD x20
BACKWARD x8
only via the disc menu. If this is the case,
press the MENU button and choose the
PLAY button when you
2. Press the
appropriate subtitle on the disc menu.
reach the desired point to resume normal
playback.
Angle Selection
Notes:
Some DVDs contain scenes which have been
• The unit mutes sound and subtitles during
shot from a number of different angles. For
reverse and forward scan of DVDs.
these discs, the same scene can be viewed
• The fast playback speed may differ
from each of these different angles.
depending on the disc.
1. While you are playing a DVD with different
angles recorded, press the ANGLE button
Skipping to a Different Chapter/Title
to view the number of current angles
• Press the
PREV button to go back to
available.
current or previous chapters/tracks.
2. Press the ANGLE button repeatedly to
NEXT button to advance
• Press the
change the scene to the next recorded
chapters/tracks.
angle. e.g.
• For audio CDs, use the number buttons on
the remote control to jump immediately to
the desired track number.
Slow-motion Play
1. Press the SLOW button on the remote in
play mode.
• Each time the SLOW button is pressed, the
speed of slow-motion playback changes in
the following sequence:
• After approx. two seconds, playback will
SF 1/2
SF 1/3
SF 1/4
SF 1/5
continue from the new angle you selected.
• If no button is pressed within 10 seconds,
PLAY
SF 1/7
SF 1/6
playback continues without changing the
current angle.
2. Press the
PLAY button to return to
normal playback speed.
Notes:
• This function can only be used for discs
on which scenes shot from multiple angles
have been recorded.
• If only one angle is recorded, “
: 1/1” is
displayed.
6
DRC300i IB ENG REV1.indd 1
Zooming into an image
While a disc is playing, press the ZOOM button to enlarge the image in several levels.
• While an image is zoomed, you can use the
,
,
or
CURSOR button to shift the view
and display the part you want.
• To return to normal view, press the ZOOM button until the “ZOOM: OFF” shows. The screen
will return to normal.
• When you reach the edge of the image, the display will not shift anymore in that direction.
Display Function
While the disc is playing, press the DISPLAY button on the remote control repeatedly to display
information on operation status.
e.g.
Elapsed Time:
Elapsed time from the beginning of the
chapter/title which is currently playing.
Chapter Remaining time
Remaining Time:
-
Remaining time of the chapter/title which is
C
00:12:03
currently playing.
Title Elapsed time
T
00:30:15
Total time
-
T
02:01:22
LoCATING A DESIRED SECTIoN
Locating a specific chapter / track
Locating a specific time
If you know the chapter / track number you
You can move to a specific location by
want to play, you can locate a specifc chapter
entering its corresponding time (hours,
/ track by directly selecting a chapter / track
minutes, seconds)
number.
1. Press the GOTO button.
1. Press the GOTO button to search your
2. Press
or
button to highlight time.
desired chapter / track.
3. Press the corresponding number buttons
2. Press
or
button to highlight a chapter /
for the setting point you want.
4. Press the OK button to confirm. The unit
track and press the corresponding number
button(s) for the chapter you want.
will start playback about 3 seconds later.
3. Press the OK button to confirm. The unit
will start playback about 3 seconds later.
Notes :
• Some discs may not respond to this
process.
• Some scenes may not be located as
precisely as you specified.
Locating a specific title
• This
method
for
accessing
specific
If a DVD disc contains title numbers, you can
locations is available only within the current
locate a specific title by directly selecting a
title of the DVD disc.
title number.
1. In stop mode, press the GOTO button.
2. Press
or
button to highlight a specific
field and press the corresponding number
button(s) for the title you want.
3. Press the OK button to confirm. The unit
will start playback about 3 seconds later.
REPEAT PLAYbACK
To resume normal playback
You can play a specific title or chapter
repeatedly. (Title repeat, chapter repeat, A-B
3. Press the REPEAT DISC button until the
repeat)
indicator displays on the
REP:
[ OFF ]
screen.
Repeating a chapter
You can play the same chapter repeatedly.
1. While the disc is playing, press the REPEAT
You can play a specific section repeatedly.
DISC button until the
REP: [ CHAPTER ]
Repeating a specific section
indicator displays on the screen. The
1. While the disc is playing, press the
current chapter is played repeatedly.
REPEAT A-B button at the beginning of
Repeating a title
the section (
is displayed) you
REPEAT A-
You can play the same title repeatedly.
want to play repeatedly.
2. While
the
disc
is
playing,
press
2. Press the REPEAT A-B button again at
the REPEAT DISC button until the
the end of the section (
is
REPEAT A-B
indicator displays on
REP:
[ TITLE ]
displayed).
the screen. The current title is played
3. The unit will immediately begin replaying
repeatedly.
your selection.
To resume normal playback
To resume normal playback
3. While
the
disc
is
playing,
press
4. While the disc is playing, press the
the REPEAT DISC button until the
REPEAT A-B button until the
A-B CANCEL
indicator displays on the
REP:
[ OFF ]
indicator displays on the screen.
screen.
Notes:
You can play a single track and whole disc
• Some discs may not permit A-B repeat
repeatedly.
operation.
• A-B repeat can only be used within the
Repeating a single track
same title. If the start and end of the
You can play the same track repeatedly.
section to be repeated are in different titles,
1. While
the
disc
is
playing,
press
A-B repeat is cancelled.
the REPEAT DISC button until the
• You can specify a segment only within the
indicator displays on
REP:
[ REP 1 ]
current title or track.
the screen. The current track is played
• The A-B repeat function does not operate
repeatedly.
in scenes where different camera angles
Repeating a whole disc
are recorded.
2. While
the
disc
is
playing,
press
the REPEAT DISC button until the
indicator displays
REP:
[ REP ALL ]
on the screen. The whole disc is played
repeatedly.
7
PRoGRAmmAbLE mEmoRY
The two types of programmed playback provided by this unit are title/chapter programmed
playback and track programmed playback.
Title / Chapter programmed playback
1. Press the MEMORY button.
2. Enter the title numbers in
. Use
button to move the
highlight to chapter and enter the chapter numbers in
.
3. Use
,
,
or
button to move to the other field.
4. Repeat steps 2 to 3.
PLAY button to start the programmed
5. Press the
playback.
Note: If you press the STOP button twice, the programmed
selection will be cleared.
Track programmed playback
1. Press the MEMORY button.
2. Enter the track numbers in
.
3. Use
,
,
or
button to other field.
4. Repeat steps 2 to 3.
5. Press the
PLAY button to start the programmed playback.
PLAYING PICTURE FILE DISC
This unit can play picture files recorded on
CD-R and CD-RW discs.
Playing a Picture File Disc
1. Open the disc door.
2. Place a picture file disc onto the tray with
label side up.
3. Close the disc door.
4. The unit will load the disc and automatically
display the contents of the disc on the
Folders
Files within the
screen, while playing the beginning of the
current folder
first picture file. These files will then be
NOTE:
played back one by one.
• You can press the
PAUSE button to
5. Press
or
button to select a picture file
PLAY
interrupt playback, and press the
to view.
button to resume playback.
6. Press the
,
,
or
CURSOR button
• You can use the GOTO function or use the
to view and select the files that you want to
numbered buttons to enter the number of a
view, then press the OK button to confirm
picture file to quickly select the image.
the selected file.
• Press the ANGLE button on the remote control
to rotate the picture orientation by 90°.
iPod FEATURES
iPod Dock Adapter
Connecting your iPod
Before connecting your iPod, you need to
Warning: To prevent damage to the unit and/
install the appropriate iPod Dock Adapter
or your iPod, connect or remove your iPod
(supplied with the iPod) in the dock of the
when the unit is powered off or the unit is not
unit.
in the iPod mode.
1. Ensure the appropriate iPod Dock adapter
Installing the iPod Dock Adapter
that was supplied with your iPod is
1. Push to open the iPod docking door.
installed.
2. Place your iPod Dock Adapter into the
2. Insert your iPod into the connector in the
dock until it sits firmly in place.
dock.
3. Press the SOURCE button to select the
iPod Dock Adapter
iPod mode. Your iPod will be connected
automatically, and iPod Home menu
appears.
Home
Docking System for iPod
Welcom
Music
Removing the iPod Dock Adapter
Photos
1. Remove the iPod Dock Adapter as
Videos
shown.
Settings
2. Replace it with another one you need.
Note:
• Your iPod will be charged automatically
(until fully charged) once it is connected,
no matter whether the unit is in iPod mode
or not.
• Make sure the software of iPod is the
latest.
IMPORTANT:
Playing Music
Before docking your iPod. MAKE SURE your
1. In iPod Home menu, use the
/
button
iPod has the latest FIRMWARE.
to select Music and press the OK button.
2. Use the
/
button to select from
Playlists, Artists, Albums, Songs, Genres
or Composers. Press the OK button to
enter.
3. Use the
/
button to navigate the iPod
menu lists and select songs, press the OK
button to begin playback. (You may also
use the control wheel and keys on your
iPod to operate it.)
PAUSE button to pause, press
• Press the
PLAY button to resume.
the
• Press the
/
button to skip to the
previous / next song.
• Press the
/
button to begin fast
PLAY button
reverse/forward, press the
to resume normal playback.
8
• Press REPEAT DISC button to select a
5. Press RETURN button to end the photo
repeat playback mode (a single repeat or
viewing and go back to the previous
all songs repeat). Press again repeatedly
menu.
to cancel this repeat playback.
Note :
4. Press the RETURN button to go back to
Make sure video
the previous menu.
out is activated in
the setting of iPod
Classic
or
iPod
Playing Photos
Nano.
1. In iPod Home menu, use the
/
button
to select Photos and press the OK button.
Playing Videos
“Navigate your iPod Photo Library directly
1. In iPod Home menu, use the
/
button
from your iPod” will appear on the screen.
to select Videos and press the OK button.
2. Use the
/
button to select from Movies,
Home
Music Videos, TV Shows, Video Podcasts
Docking System for iPod
or Rentals, press the OK button to enter.
Welcom
(“Navigate your iPod Video Library directly
Music
Photos
from your iPod” will appear on the screen if
Videos
your are using an iPod touch.)
Settings
3. Use the
/
button to navigate the iPod
menu lists and select a video, press the
OK button to begin playback. (You may
also use the control wheel and keys on
2. Use the
/
button to navigate the iPod
your iPod to operate it.)
menu lists and select a photo, press the
OK button to begin playback. (You may
also use the control wheel and keys on
Home
your iPod to operate it.)
Docking System for iPod
PAUSE button to pause, press
• Press the
Welcom
PLAY button to resume .
the
Music
Photos
• Press the
/
button to skip to the
Videos
previous / next photo.
Settings
3. Press the RETURN button to go back to
the previous menu.
• Press the
PAUSE button to pause, press
Using a iPod Touch to view the photo
the
PLAY button to resume.
1. In iPod Home menu, use the
/
button
• Press the
/
button to skip to the
to select Photos and press the OK button.
previous / next movie.
“Navigate your iPod Photo Library directly
• Press the
/
button to begin fast
from your iPod” will appear on the screen.
PLAY button
reverse/forward, press the
2. Touch the “Photos” selection on iPod panel,
to resume normal playback.
and then select the photo your prefer.
4. Press the RETURN button to go back to
3. Touch the “
” to confirm the photo.
the previous menu.
4. Touch the “ Yes ” to activate iPod’s video
output. The photo will appear on the
Note : Make sure TV Out in iPod is set to ON
screen.
when you are playing the video.
Step 2
Settings
1. In iPod Home menu, use the
/
button
to select Settings and press the OK
button.
2. Use the
/
button to select from Shuffle,
Repeat or Lanuage. Press the OK button
to enter the settings.
3. Use the
/
button to a setting, press the
OK button to confirm.
4. Press the RETURN button to go back to
Step 3
Step 4
the previous menu.
Home
Docking System for iPod
Welcom
Music
Photos
Videos
Settings
5. Press RETURN button to end the photo
• Shuffle : Select from Shuffle Off, Shuffle
viewing and go back to the previous
Songs and Shuffle Albums.
menu.
• Repeat : Select from Repeat Off, Repeat
One and Repeat All.
• Language : Select OSD language.
Using a iPod Classic / iPod Nano to
view the photo
WARNING: Due to the i-Pod limitation, not
1. In iPod Home menu, use the
/
button
all functions of some i-Pod models can be
to select Photos and press the OK button.
controlled via the remote control.
“Navigate your iPod Photo Library directly
from your iPod” will appear on the screen.
Please Navigate directly on your iPod
2. Press the
/
button to select “Photos”,
OR
and then press the OK button to confirm.
Press The [CLEAR] Key
3. Use the
button to select a photo,
to go back to main menu
press the OK button to begin playback.
Step 2
Step 3
If the above screen appears, you may need
to control the iPod Library directly from your
iPod.
iPod is a trademark of Apple Computer, Inc.,
registered in the U.S. and other countries.
4. Press OK button twice to activate photo
showing to TV screen.
Step 4
9
CUSTomIZING THE FUNCTIoN SETTINGS
LANGUAGE SETUP
There are four options in the main setup
menu: System Setup, Language Setup, Audio
1. Press the SETUP button in DVD mode.
Setup and Video Setup.
2. Use
button to select Language Setup.
In DVD mode, press SETUP to bring up the
main menu. Select one of the menu icons
OSD LANGUAGE
across the top of the screen using the
or
AUDIO LANG
buttons. The menu’s options are displayed on
SUBTITLE LANG
the left side of the screen. Press the
,
,
MENU LANG
or
buttons to move to the option’s choices
on the right. Then press OK to select. Press
SETUP or RETURN if you want to exit.
3. Use
,
,
or
button to select a
language, then press the OK button.
SYSTEM SETUP
The screen will change to your selected
1. Press the SETUP button in DVD mode.
language immediately.
2. Select System Setup in the main menu
3. To exit the SETUP MENU and return to
using the
,
,
or
buttons.
the normal screen, press the RETURN or
SETUP button.
Notes:
HD OUTPUT
• Some DVDs may not play in the audio
VIDEO
TV TYPE
language selected. A prior language may
DEFAULT
be programmed on the disc.
• Some DVDs may be set to display subtitles
in a language other than the one you
selected. A prior subtitle language may be
3. Select a menu option using the
or
programmed on the disc.
buttons and press OK button.
• Some DVDs allow you to change subtitle
selections only via the disc menu. If this
HD OUTPUT
is the case, press the MENU button and
This lets you select the resolution output
choose the appropriate subtitle language
according
to
the
connected
TV.
The
from the selection on the disc menu.
Composite Video Out (YELLOW jack) will be
• Some DVDs may not include your pre-
kept in standard resolution for all HD OUTPUT
selected language. In this case, the DVD
settings.
player automatically displays disc menus
consistent with the disc’s initial language
• Supported HD JPEG mode: 480p, 720p,
setting.
1080I and 1080p.
AUDIO SETUP
VIDEO
1. Press the SETUP button in DVD mode.
Only available when HD OUTPUT is 480p.
2. Select Audio Setup in the main menu using
the
or
buttons.
INTERLACE-YUV :
• Select if you are connecting the player
with Component Video outputs to a non-
Progressive Scan TV.
P-SCAN YPBPR :
AUDIO OUT
• Select if you are connecting the player with
Component Video outputs to a Progressive
Scan TV.
S-VIDEO :
• Select if you are connecting the player with
S-VIDEO output to a TV with S-VIDEO
3. Select a menu option using the
,
,
or
input.
buttons and press OK button.
TV TYPE
Depending on the format of the DVD, you can
AUDIO OUT
choose the picture format (aspect ratio) best
Select the output sound format corresponding
suited to the format of your TV screen:
to your system connection. When making
connection to a TV or stereo system via the
4:3 PS (Pan Scan)
analog audio jacks, select PCM or RAW.
• When
wide-screen
Cut off when a wide-
video is played, this
screen video image is
RAW: Does not have a Dolby Digital Decode.
mode clips the right
played.
PCM: Select when connected to a 2 channel
and left sides of
digital stereo amplifier.
the image so that it
can be viewed on a
• If apply HDMI connection to TV, make sure
conventional screen.
to select PCM, audio signal passing to TV
• Some
wide-screen
via HDMI cable.
DVDs that do not
PAN SCAN
permit
Pan
Scan
VIDEO SETUP
mode playback are
automatically played
1. Press the SETUP button in DVD mode.
in
letterbox
mode
2. Select Video Setup in the main menu using
(black bands top and
the
or
buttons.
bottom).
LETTER BOX
4:3 LB (Letter Box)
• When
wide-screen
BRIGHTNESS
video
is
played
CONTRAST
in this mode on a
HUE
SATURATION
conventional screen,
SHARPNESS
black bands appear
WIDE SCREEN
at the top and bottom
of the screen.
16:9 (Wide screen)
3. Select
Brightness,
Contrast,
Hue,
• This is the correct mode for playing wide-
Saturation or Sharpness using the
or
screen videos on a wide-screen.
buttons, hightlight your selections and
Notes :
press OK button.
• The displayable picture size is preset on the
DVD disc. Therefore the playback picture
of some DVD discs may not conform to the
picture size you select.
• When you play DVD discs recorded in the
4:3 aspect ratio, the playback picture will
always appears in the 4:3 aspect ratio
regardless of the TV TYPE setting.
Specifications and external appearance are
DEFAULT
subject to change without notice.
It takes 3-5 seconds to reset the unit to the
Printed in China
811-300I91W011
factory default.
10
7/14/2008 9:51:19 AM
Advertisement
Related Manuals for RCA DRC300i
Summary of Contents for RCA DRC300i
- Page 1 [ REP ALL ] indicator displays on the screen. The whole disc is played repeatedly. DRC300i IB ENG REV1.indd 1 PRoGRAmmAbLE mEmoRY CURSOR button to shift the view The two types of programmed playback provided by this unit are title/chapter programmed playback and track programmed playback.
- Page 2 Please check and identify the supplied accessories. It is forbidden by law to copy, broadcast, show, technology that is protected by U.S. patents • To order accessories visit web site http://www.1800customersupport.com/RCA broadcast on cable, play in public, or rent and other intellectual property rights. Use of Remote Control ...