Page 1
Model No. PFTL72582 Serial No. Serial Number Decal QUESTIONS? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or if there are missing or damaged parts, we will guarantee complete satis- faction through direct assistance from our factory.
2. Use the treadmill only as described in this manual. 3. Place the treadmill on a level surface, with at least eight feet of clearance behind it. Do not place the treadmill on any surface that blocks air openings.
Page 4
Servicing other than the procedures in this manual should be performed by an authorized service representative only. 24. This treadmill is intended for in-home use only. Do not use this treadmill in any commer- cial, rental, or institutional setting.
The model number of the treadmill is PFTL72582. The serial num- ber can be found on a decal attached to the treadmill (see the front cover of this manual for the location).
This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
OPERATION AND ADJUSTMENT THE PERFORMANT LUBE WALKING BELT Your treadmill features a walking belt coated with PERFORMANT LUBE , a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking plat- form. They will deteriorate the walking belt and cause excessive wear.
Page 8
Step onto the foot rails of the treadmill. Find the clip attached to the key (see the drawing above), and slide the clip onto the waistband of your clothing. Follow the steps below to operate the console.
Page 9
STOP button for two seconds. Adjust the incline of the treadmill as desired To change the incline of the treadmill, press the INCLINE buttons. Each time one of the buttons is pressed, the incline will change by 0.5%. The but- tons can be held down to change the incline quickly.
Page 10
TIME/INCLINE display. This number is the maxi- mum incline that the treadmill will reach during the selected program. If you want to change the maximum incline setting, press the INCLINE setting can be from 4% to 10%. If the setting is in- creased, the difficulty level of the entire program will increase.
Page 11
The incline of the treadmill can be changed by pressing the INCLINE buttons. The time remaining in the program will be shown in the TIME/INCLINE display.
2. Move your right hand to the position shown and hold the treadmill firmly. Using your left hand, pull the latch knob to the left and hold it. Raise the treadmill until the latch pin is aligned with the hole in the catch. Insert the latch pin into the catch.
Page 13
Do not hold or push on the book holder or the book holder may be damaged. 2. Tilt the treadmill back until it rolls freely on the front wheels. Carefully move the treadmill to the desired location. Never move the treadmill without tipping it back. To reduce the risk of injury, use extreme caution while moving the treadmill.
2. SYMPTOM: THE POWER TURNS OFF DURING USE a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
Page 15
Reed Switch Screw (109) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading. 5. SYMPTOM: The walking belt slows when walked on a.
It may also be helpful to use one of the consoleÕs FAT BURN programs (see pages 10 to 13). For maximum fat burning, adjust the speed and incline of the treadmill until your heart rate is near the middle number in your training zone. Aerobic Exercise If your goal is to strengthen your cardiovascular sys- tem, your exercise must be Òaerobic.Ó...
Page 17
SUGGESTED STRETCHES The correct form for several basic stretches is shown at the right. Move slowly as you stretchÑnever bounce. 1. Toe Touch Stretch Stand with your knees bent slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible.
PART LISTÑModel No. PFTL72582 No. Qty. Description Center Track Foot Rail Left Foot Rail Cap Front Roller Adjustment Nut Isolator Bumper Platform Screw Walking Platform Frame Pivot Bolt Frame Pivot Spacer Walking Belt Front Roller/Pulley Small Screw Motor Belt Upright/Base...
Page 19
No. Qty. Description Magnet Incline Reed Switch Switch Wire Reed Switch Clip Incline Motor Spacer Optic Disk Optic Switch Nut Optic Switch Washer Optic Switch Bolt Optic Switch Handrail Endcap Roller Guard Interface Bracket 14Ó White Wire, 2 F 8Ó White Wire, M/F Specifications are subject to change without notice.
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give the following information: ¥ The MODEL NUMBER OF THE PRODUCT (PFTL72582). ¥ The NAME OF THE PRODUCT (PROFORM ¥ The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual).