Advertisement
Quick Links
GENERAL INFORMATION
The 5827BD Wireless Bidirectional Console is designed to be used in
conjunction with a 58ooTM Transmitter Module.
quantity) may be used in conjunction with the same 5800TM. The 5800TM is
compatible with any control panel that is also equipped with a 4281 type (5700
System) or 5881 type (5800 System) RF receiver.
5827 Bidirectional Console
The 5827BD can operate the protection system similarly to other consoles, via its
keypad. In addition, its three LEDs (red, green, and yellow) and piezoelectric
sounder can indicate status information relative to: system arming/ trouble/
emergency, RF transmission/confirmation, and 5827BD programming and power.
The keypad configuration is similar to that of standard consoles. The [✱] key,
however, is also the [ON/STAT] (powerup and system status inquiry) key instead
of a "READY" key, as it is on other consoles (see OPERATION ). There are three
panic keys: A, B, and C (comparable to other consoles' panic key pairs of 1/✱),
✱/#, and 3/# respectively).
The console, if so programmed, also features "Quick Key" operation, which
allows use of the [#] key instead of entry of the security code when performing
functions.
5800TM Transmitter Module
For every installation of one or more 5827BDs, one 5800TM is required. It
complements the 4281 or 5881 RF receiver in that it transmits the information to
be displayed on, or sounded by, the 5827BD. No modification to the control is
necessary. It connects directly to the control's console connection points, as
described later.
INSTALLATION
5827BD Bidirectional Console Installation
The console is designed to be portable, for use throughout the protected premises. If desired, it may be stored on its accompanying
mounting bracket (easily installable via two countersunk mounting holes). Keyhole slots on the rear of the console slip onto two hooks
on the mounting bracket, and the console is easily removable.
When operating, or selecting a location for storing the console, observe the same precautions as used for locating the wireless
system's other transmitters (see the control panel's instruction manual). For example, operating the console on or near large metal
objects may decrease range and/or block transmissions.
1.
Install the console's battery by sliding off the battery compartment cover on its rear. Observe polarity! Replace the cover.
2.
Program the console's memory as follows:
a.
Power up the console by depressing the [✱] key. The yellow LED blinks . In case the console was previously programmed,
the system status may also be annunciated (see Power-up and System Status Inquiry on next page).
b.
Enter console programming mode by depressing the [1] and [3] keys (both at the same time) for 3 seconds. Alternate
blinking of the red and green LEDs confirms that the unit is in console programming mode.
c.
Program the desired functions, in the order given in the table that follows. Note that every sequence starts with a [✱]
and ends with a [#].
1.
Enter YOUR System's 4-Digit Master Code
Enable Quick Key Operation
2.
Enter YOUR 5700/5800System's House ID
3.
Enter RF System Used:
4.
5.
Exit console programming mode.
Notes: 1) Upon the detection of each closing '#', a confirmation sound is generated:
•
following a valid entry, a triple beep
•
following an erroneous entry, a single, long (2 sec) beep.
2) The 5827BD can be reprogrammed at any time.
3)
Each time the console-programming mode is entered, Quick Key operation is disabled and must be reenabled, if so desired.
PRELIMINARY
7/25/03..tp
Installation and Setup Guide
Additional 5827BDs (any
FUNCTION
(arm, disarm, and chime)
or
(Arm and chime, but not disarm)
(e.g., 06) selected from 01-31
5700 System (4281 RF receiver)
or
5800 System (5881 RF receiver)
Wireless Bidirectional Console
ANTENNA
SOUNDER
LEDS
GREEN
YELLOW
RED
C (3/#)
B ( /#)
*
A (1/ )
*
PANIC KEYS
POWER-UP KEY
KEY SEQUENCE
[✱]
[8]
[4-Digit Master Code]
[✱]
[1]
[4-Digit Master Code]
or
[✱]
[2]
[4-Digit Master Code]
[✱]
[9]
[0]
[6]
[✱]
[5]
[7]
or
[✱]
[5]
[8]
[✱]
N6484V4 7/03
5827BD
ARM
SEND/RCV
READY
1
2
3
4
5
6
8
7
9
0
#
*
[#]
[#]
[#]
[#]
[#]
[#]
Advertisement
Related Manuals for ADEMCO 5827BD
Summary of Contents for ADEMCO 5827BD
- Page 1 POWER-UP KEY complements the 4281 or 5881 RF receiver in that it transmits the information to be displayed on, or sounded by, the 5827BD. No modification to the control is necessary. It connects directly to the control’s console connection points, as described later.
- Page 2 Power-up and System Status Inquiry Touching the [✱] ([ON/STAT]) key powers up the 5827BD, and sends an inquiry to the 5800TM, requesting the system status to be annunciated (see table on next page). Subsequent depressions of the same key will initiate additional inquiries.
- Page 3 YELLOW BLINK SILENT UPON 5827BD POWER-UP (SEND/RCV) RF TRANSMISSION IN PROGRESS OR RECEPTION JUST COMPLETED and, as explained in the INSTALLATION section for the 5827BD: RED & ALTERNATELY SILENT 5827BD IS IN CONSOLE PROGRAMMING MODE GREEN BLINKING With 4111CM and VISTA 20 systems, status monitoring is restricted to Partition 1; however, each partition can be controlled by 5827BDs programmed to the partition’s House ID.
- Page 4 24 months from the date stamp control on the product(s) or, for product(s) not having an ADEMCO date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply.