Polaroid PTV-701 User Manual

7.0" LCD Display
Portable Digital Television Portable Digital Television
PTV-701
User Guide
www.polaroid.com
Polaroid and Polaroid & Pixel are trademarks of PLR IP Holdings, LLC, used under license. PLR
IP Holdings, LLC does not manufacture this product or provide any Manufacturer's Warranty or
support.

Getting started

Charging
This television contains a built-in rechargeable battery. You may power the
television by charging its internal battery or you may power the television by
using the included AC adaptor. Follow the instructions below to charge the
television properly.
1. Connect the AC adaptor to the DC 9-12V IN jack on the TV and plug it into a
wall receptacle.
2. Charging time depends on whether the TV is ON during charging or in
standby mode.
1 If the TV is ON – the charge time is approximately 6 hours.
If the TV is in standby mode – the charge time is approx imately 4 hours.
3. When battery strength is low, the TV will display the following icon on the
screen:
4. The [Standby/Power] indicator light on the front of the TV turns green when:
The power cord is connected, and the TV is fully charged.
The TV is running on battery power.
Note: Use the included car charger to charge the TV in a car
or boat.

Scanning for channels

The first time the television is turned on you must scan for available channels.
You should also scan for available channels whenever you are in a new area, or
when reception is bad.
1. Make sure that the antenna is connected to the TV and slide the power
[ON/OFF] switch to the ON position.
2. When you turn on the TV for the
first time, the following screen
will be displayed:
2
3. If this screen does not appear, then press the [AUTO/OK] button on the TV.
4. Press the [VOL+] button to select "Yes" and press [AUTO/OK] button
to confirm.
5. The TV will start scanning
for available channels and
store them into memory.
In the box Included
Digital TV
A / V
Cables
2 - (AAA)
Batteries
1. [MUTE] button
2. [PICTURE] button
3. [MENU] button
4. [SLEEP] button
5. [ ] left button
6. Numeric buttons
7. [ ] previous channel
button
8. [VOL-] volume down
button
9. [POWER] button
10. [MTS] sound field
button
11. [ZOOM] display
mode button
12. [EXIT] button
13. [EPG] program
guide button
14. [ ] up button
15. [ ] right button
16. [ENTER] button
17. [ ] down button
[TV/AV] source button
18.
19. [INFO] program information button
20. [CH+] channel up button
21. [CH-] channel down button
22. [ ---- ] channel program button
23. [VOL+] volume up button
,this means it is time to recharge the battery.
Do not move or unplug the TV while scanning
for channels/programs as this will interrupt the
scanning process and you will not receive all
possible channels/subchannels.
Remote Antenna
Control
AC DC
Adaptor Car Charger
User Guide
Remote control
9
10
1
11
2
12
13
3
14
4
15
16
5
17
6
18
19
7
20
8
21
22
23
Connecting the antenna
1. With the antenna in the down position, screw it into the RF IN antenna jack
on the TV.
2. For the best reception, stretch the antenna out to its fullest length before
scanning for channels.
Note: The antenna must be connected to receive
the highest amount of channels available during
channel scanning.
Scanning by remote control
1. Press the [MENU] button on
the remote and press the [
button to select:
2. Press the [ ] button to select
"Antenna".
3. Press the [ ] button to select
"Air" or "CATV" (cable TV),
depending on the type of
connection.
4. Press the [ ] button to scroll to
"Auto Scan" and press the [
button twice. The TV will start
scanning for available channels
and store them into memory.
Note: Do not move or unplug the TV while scanning for
channels/subchannels.
This television is not meant to be used in a
moving vehicle. ATSC Digital tuners are not
capable of receiving a signal when in motion.
Location of controls
1. LCD screen
2. Dual speakers
3. [Standby/Power] indicator
4. [MENU] button
1
5. [CH-] button
6.
[CH+] button
2
7. [AUTO/OK] button
8. [VOL-] button
9. [VOL+] button
10. [MODE] button
11. Remote sensor
12
12. RF IN antenna jack
13. VIDEO IN jack
13
14. AUDIO IN L jack
14
15.
AUDIO IN R jack
15
16. Headphone jack
16
17. Power [ON/OFF] switch
18. DC 9-12V IN jack
19. TV stand (pull)
20. Battery compartment
20
Installing the batteries
1. Open the battery cover.
2. Place the 2 (AAA) batteries (included) into the
compartment. Be sure the positive and negative
terminals are positioned correctly as shown.
3. Close the battery cover.
Remote control
Cover
]
]
3 4 5 6 7 8 9 10 11
17
18
19
Batteries
Select