Planet VoIP Analog Telephone Adapter VIP-157S User Manual

Planet VoIP Analog Telephone Adapter VIP-157S User Manual

Voip analog telephone adapter
Hide thumbs Also See for VoIP Analog Telephone Adapter VIP-157S:
Table of Contents

Advertisement

VoIP Analog Telephone Adapter
VIP-156/VIP156PE/VIP-157/VIP-157S
User's manual
Version 3.1
1

Advertisement

Table of Contents
loading

Summary of Contents for Planet VoIP Analog Telephone Adapter VIP-157S

  • Page 1 VoIP Analog Telephone Adapter VIP-156/VIP156PE/VIP-157/VIP-157S User’s manual Version 3.1...
  • Page 2: Ce Mark Warning

    Copyright Copyright (C) 2008 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
  • Page 3 Revision User’s Manual for PLANET VoIP Analog Telephone Adapter: Model: ATA Rev: 3.1 (2008, February) Part No. EM-VIP_ATAV3.1...
  • Page 4: Table Of Contents

    Chapter 1 ... 6 Introduction ... 6 Overview... 6 Package Content ... 7 Physical Details ... 7 LED Display & Button... 10 Chapter 2 Preparations & Installation... 12 Physical Installation Requirement... 12 LAN IP address configuration via web configuration interface ... 13 Chapter 3 Network Service Configurations...
  • Page 5 Codec ID Setting ... 37 DTMF Setting ... 38 RPort Settings... 38 Other Settings... 39 STUN settings ... 39 Auto Configuration... 40 PTT Settings ... 40 Cancel without to tag... 41 MAC CIone Setting... 41 Tone Settings ... 43 Advanced Settings... 43 System Authority...
  • Page 6: Chapter 1

    Overview Based on years of VoIP manufacturing experiences, PLANET Technology VoIP total solutions are known for advanced implementation of standards based telephony with mass deployment capability. Cost-effective, easy-to-install and simple-to-use, the PLANET VIP-156/VIP-157/VIP-157S VoIP Phone Adapter (“ATA” in the following term) converts standard telephones to IP-based networks. The service providers and enterprises offer users traditional and enhanced the telephony communication services via the existing broadband connection to the Internet or corporation network.
  • Page 7: Package Content

    • Voice processing: Voice Active Detection, DTMF detection/ generation, G.168 echo cancellation (16mSec.), Comfort noise generation (CNG) • In band, out-of-band, and SIP-info DTMF support Package Content The contents of your product should contain the following items: VoIP Telephone Adapter Power adapter Quick Installation Guide User’s Manual CD...
  • Page 8 Left / Right Panel of VIP-156 Front Panel of VIP-156PE Left / Right Panel of VIP-156PE...
  • Page 9 Front Panel of VIP-157 Left / Right Panel of VIP-157 Front Panel of VIP-157S...
  • Page 10: Led Display & Button

    LED Display & Button 12V DC Reset Machine default IP is http://192.168.0.1. Press RESET Note button on rear panel over 5 seconds will reset the VoIP Phone Adapter to factory default value. (Except speed dial and call forward settings) Left / Right Panel of VIP-157S RJ-45 connector, to maintain the existing network structure, connected directly to the PC through straight CAT-5 cable RJ-45 connector, for Internet access, connected directly to...
  • Page 11 LED display of VIP-156 / VIP-156PE LED Indicators Power is supplied to the device. The Status LED will be flashing when the machine is operational STATUS LNK/ACT OFF: the device is connected to LAN at 10Mb/s. ON: the device is connected to LAN at 100Mb/s. OFF: the phone is idle.
  • Page 12: Chapter 2 Preparations & Installation

    Physical Installation Requirement This chapter illustrates basic installation of ATA analog Phone Adapter ((“ATA” in the following term)) • Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors. • TCP/IP protocol must be installed on all PCs. For Internet Access, an Internet Access account with an ISP, and either of a DSL or Cable modem Administration Interface PLANET ATA provides GUI (Web based, Graphical User Interface) for machine management and administration.
  • Page 13: Lan Ip Address Configuration Via Web Configuration Interface

    Please locate your PC in the same network segment Note (192.168.0.x) of ATA. If you’re not familiar with TCP/IP, please refer to related chapter on user’s manual CD or consult your network administrator for proper network configurations. LAN IP address configuration via web configuration interface Execute your web browser, and insert the IP address (default: 192.168.0.1) of VIP in the adddress bar.
  • Page 14 #112xxx*xxx*xxx* Setup Static IP Address xxx# #113xxx*xxx*xxx* Set Network Mask xxx# #114xxx*xxx*xxx* Set Gateway IP Address xxx# #115xxx*xxx*xxx* Set Primary DNS Server xxx# #190# Unlock #191# Lock #195# Reboot #198# Factory Reset 0* To switch PSTN mode Following keypad commands can be used to display the network settings enabled on ATA via voice prompt.
  • Page 15 #125# Check Primary DNS Server Setting #126# Check LAN IP Address #128# Check Firmware Version Following keypad commands can be used to set up the main function . IVR Menu Choice Machine operation #138# Enable call waiting #139# Disable call waiting #160# Update firmware #510#...
  • Page 16 Port enable forward to FXO #147+Number# Port #116# Enable PPTP function #117# Disable PPTP function #118# Enable VLAN function #119# Disable VLAN function Please contact your Internet service provider to obtain the Internet access type, and select the proper network setti Hint fter confirming the modification you’ve done, Please click on the Submit button to apply settings and rowse to “Save &...
  • Page 17: Chapter 3 Network Service Configurations

    Configuring and monitoring your ATA from web browser The ATA integrates a web-based graphical user interface that can cover most configurations and machine status monitoring. Via standard web browser, you can configure and che from anywhere around the world. Overview on the web interface of ATA With web graphical user interface, you may have: More comprehensive setting feels than traditional command line interface.
  • Page 18 VoIP Phone Adatper main page...
  • Page 19: Chapter 4 Voip Telephone Adapter Configurations

    VoIP Telephone Adapter Configurations Phone Book ATA can set up 140 records of Phone Book. User can dial the Name records to make calls via Phone Book feature. Field Phone Book Page Phone Name Select Description The default is Page 1. It can select Page1 ~ Page 14 to look round Phone Book records.
  • Page 20: Call Forward

    If you need to add a phone number into the Phone Book list, you need to input the position, the name, and the phone number (by URL type). When you finished a new phone list, just click the “Add Phone” button.
  • Page 21 speed dial number you choose. Busy Forward: If you are on the phone, the new incoming call will forward to the number you choosed. You can input the name and the phone number in URL field. No Answer Forward: If you can not answer the phone, the incoming call will forward to the number you chosen.
  • Page 22: Sntp Settings

    Call Forward function for VIP-157 SNTP settings This page defines the primary and second SNTP Server IP Address, to get the date/time information. Also you can base on your location to set the Time Zone, and how long need to synchronize again. When you finished the setting, please click the Submit button.
  • Page 23: Block Setting

    Volume Settings for VIP-154T/VIP-154PT Beside the above settings, VIP-157 also can set the volume of PSTN. PSTN-Out Volume is to set the PSTN volume for you can hear. PSTN-In Gain is to set the volume send out to the other side’s handset. Volume Settings for VIP-157 Block Setting This page defines the Block Setting to keep the phone slience.
  • Page 24: Auto Answer (For Vip-157)

    Auto Answer (For VIP-157) This page defines the Auto Answer function. You can set the Auto Answer function to answer the incoming call by the phone. If the call is come from the IP, then the VIP-157 can let user to redial the call to PSTN phone number.
  • Page 25: Dial Plan Settings

    Dial Plan Settings This page defines the Dial Plan Setting function. This function is when you input the phone number by the keypad but you don’t need to press “#”. After time out the system will dial directly. Field Description Drop Prefix The rule of add or replace code.
  • Page 26 the max length is 40. If the dialing number are match with this field, it will dial out and need Dial Now not to press the “#” key to end the dialing. It accepts the numeral or symbol, and the max length are 124. number is “0xxxx”, because the starting number is “0”, so that the system will ignore this dial plan.
  • Page 27: Flash Time Setting

    Example_4: Dial Now: *xx+#xx+11x+xxxxxx 1. If the dialing number is match with the rule of “*xx”, it will send out the dialing number directly. For example, *00/ *01/ 2. If the dialing number is match with the rule of “#xx”, it will send out the dialing number directly. For example, #00/ #01/ 3.
  • Page 28: T.38 (Fax) Settings

    waiting notice in your current call. If you set the function to Off, then you will not hear any notice. T.38 (FAX) Settings This page defines the T.38 (FAX) Setting function. You can Enable/Disable the T.38 function, and can modify the T.38 transmission port of each FXS port. T.38 (FAX) Settings for VIP-156/VIP-156PE/VIP-157 T.38 (FAX) Settings for VIP-157S Hot line Settings...
  • Page 29: Alarm Settings

    the specific number automatically. Use Hot Line: Click Enable to carry the Hot line function out. Hot line number: The hot line number, it can input the IP address or registration number. Alarm Settings This page defines the Alarm setting in this page. It provides the alarm function, and it can set up the Alarm Time to get the telephone ringed up every day.
  • Page 30: Pc Settings

    Fixed IP: It could setup the IP address manual. DHCP Client: It will acquire the IP address automatically. PPPoE: It will use the PPPoE connection method. IP: The IP address Mask: The sub net address Gateway: The default gateway address DNS Server1: The default is 168.95.192.1, it could setup the first DNS server address.
  • Page 31: Ddns Settings

    DHCP Server: It will allot the IP address automatically when enabke this function. Start IP: Start IP of lease table End IP: End IP of lease table. Network device connecting to the PC port can dynamic obtain the IP in the range between start IP and end IP Lease Time: DHCP server lease time DDNS Settings...
  • Page 32: Vlan Settings

    VLAN Settings This page defines the VLAN setting in this page. This function needs to co-operate with network devices which have VLAN function. VLAN Packets: If setup as On, it could receive VLAN messages. VID (802.1Q/TAG): Dispose VLAN ID is add a Tag header after realize enable the VLAN function. The realized voice packets transfer at the same VLAN.
  • Page 33: Dmz Settings

    DMZ Settings This page defines the DMZ setting in this page. DMZ: If setup as On, all of packets (expect SIP packets) will send to the specific IP address. DMZ Host IP: The DMZ host IP address. Virtual Server This page defines the Virtual Server setting in this page. You could define 24 virtual service information in this page.
  • Page 34: Pptp Settings

    External Port: For corresponding the external port. Server IP: To input the Server IP address. PPTP Settings This page defines the PPTP setting in this page. You could setup the PPTP Server connection information. When you finished the setting, please click the Submit button.
  • Page 35: Service Domain Settings

    Service Domain Settings In Service Domain Function you need to input the account and the related informations in this page, please refer to your ISP provider. You can register three SIP account in the ATA. You can dial the VoIP phone to your friends via first enable SIP account and receive the phone from these three SIP accounts.
  • Page 36: Port Settings

    For example: The default is realm 1, input the the telephone set. It will switch to realm 2, and it can make the SIP calls via realm 2. Port Settings This page defines the SIP and RTP port number in this page. Each ISP provider will have different SIP/RTPport setting, please refer to the ISP to setup the port number correctly.
  • Page 37: Codec Id Setting

    Codec ID Setting This page defines the Codec ID. Sometimes 2 VoIP devices with different Codec ID will cause the interopability issue. If you are talking with others got some problems, you may ask the other one what kind of Codec ID he use, then you can change your Codec ID. When you finished the setting, please click the Submit button.
  • Page 38: Dtmf Setting

    DTMF Setting This page defines the RFC2833 Out-Band DTMF, Inband DTMF and Send DTMF SIP Info in this page. To change this setting, please following your ISP information. When you finished the setting, please click the Submit button. RPort Settings This page defines the RPort Enable/Disable in this page.
  • Page 39: Other Settings

    Other Settings This page defines the Hold by RFC, Voice/SIP QoS and other settings in this page. To change these settings please following your ISP information. When you finished the setting, please click the Submit button. Hold by RFC: The default is disable, and to start up communication hold back function (RFC definition). Set enable to start up the Hold by RFC function.
  • Page 40: Auto Configuration

    Auto Configuration This page defines the Auto Configuration (Auto Provision) setting. ATA supports TFTP, FTP, HTTP and IP PBX auto configuration function in total. In IP PBX Auto Configuration Setting you need to check with your service provider if they have provided this function. Usually this function will be boundle with an IP PBX to use in the office.
  • Page 41: Cancel Without To Tag

    PTT Settings for VIP-156/VIP-157S Beside the above settings, VIP-157 also can set country of FXO port. PTT Settings for VIP-157 Cancel without to tag This function can decide the device if send the cancel tag to Proxy Server. If there has the similar symptom that the caller cancel the call before the called answer the call, the called still continue to ring up even the caller has cancel this call.
  • Page 42 MAC address for PPPoE dial-up connection. Please refer to the following operate procedures for more understandings to carry out the MAC Clone function. 1. Please login ATA and browse to “Network -> LAN Settings” page. To switch the LAN mode to NAT mode then press Save&Reboot button to save the settings and reboot machine.
  • Page 43: Tone Settings

    5. After Save&Reboot, the MAC of LAN port will become to PC’s original MAC address. Tone Settings This page defines the Tone settings. This function can setup the related parameters of Dial Tone, Ring Back Tone, Busy Tone, Error Tone and Inser Tone. When you finished the setting, please click the Submit button.
  • Page 44: System Authority

    (The Registration Server also need support this function) CPC Delay: When receive the disconnect signal, machine will to cut the voltage down to 0V after this time. CPC Duration: When starting to cut the voltage down to 0V, machine will to continue this state by this time.
  • Page 45: Save & Reboot

    Save & Reboot In Save & Reboot you can save the changes you have done. If you want to use new setting in the Phone Adapter, You have to click the Save button. After you click the Save button, the Phone Adapter will automatically restart and the new setting will effect.
  • Page 46: Auto Upgrade

    Auto Upgrade The device can update new firmware with the gz or ds file format automatically by the Auto Upgrade function. Field Update via TFTP Server HTTP Server HTTP File Path FTP Server FTP Username FTP Password FTP File Path Check new firmware Descriptions There are TFTP/ FTP and HTTP three ways to provide the auto...
  • Page 47: Reset To Default

    Scheduling (Date) Automatic Update Firmware File Prefix Next update time Note: If the Check new firmware field selected to Power On, the machine will chck the new firmware accoeding the scheduling time/date and power on. If there are new firmware can be upgraded, the machine won’t carry firmware update out automatic.
  • Page 49: Appendix A Voice Communication Samples

    Appendix A Voice Communication Samples There are several ways to make calls to desired destination in ATA. In this section, we’ll lead you step by step to establish your first voice communication via keypad and web browsers operations. Case 1: ATA to ATA connection via IP address Assume there are two ATAs in the network the IP address are 192.168.0.1, 192.168.0.2 Analog telephone sets are connected to the phone (RJ-11) port of ATAs respectively 192.168.0.1...
  • Page 50: Case 2: (Peer-To-Peer Mode) Vip-157S Port 1 To Port 2 Communications

    Case 2: (Peer-to-Peer mode) VIP-157S Port 1 to Port 2 communications Supposing one VIP-157S connects to two telephones, just pick up phone 1 and dial ‘192*168*0*1**5062’, phone 2 will ring. Analog telephone sets are connected to the phone (RJ-11) ports of VIP-157S respectively 1001 Test the scenario: 1.
  • Page 51: Case 3: Voice Communication Via Sip Proxy Server - Sip-50

    Case 3: Voice communication via SIP proxy server – SIP-50 Registration / Authentication SIP-50 IP Address: 192.168.0.50 ATA A IP Address: 192.168.0.1 Line Number: 1001 Device configurations on the ATA: STEP 1: Log in SIP-50 and create two testing accounts/password: 1001 / 123 (for ATA A), and 1002 / 123 (for ATA B) for the voice calls.
  • Page 52 STEP 3: Repeat the same configuration steps on ATA B, and check the machine registration status, make sure the registrations are completed. Test the scenario: 1. Pick up the telephone on ATA A 2. Press the keypad: 2002 shall be able to connect to the ATA B 3.
  • Page 53: Case 4: Voice Communication Via Ip Pbx System - Ipx-2000 (Auto-Config)

    Case 4: Voice communication via IP PBX system – IPX-2000 (Auto-config) In the following sample, we’ll introduce how to integrate the ATA with our IP PBX system IPX-2000 via Auto-config feature. Registration / Authentication IPX-2000 LAN IP Address: 192.168.0.50 ATA A IP Address: 192.168.0.1 Line Number: 1001 Device configurations on the IPX-2000: STEP 1:...
  • Page 54 STEP 2: Please browse to the Device button for set up the Auto Config configuration. STEP 3: Please fill out the Vendor Prefix code and MAC Address of ATA. Note: The following are the Vendor Prefix of devices: 1. VIP-156: pla156 2.
  • Page 55 STEP 5: After setting up the parameters, please browse to the Service press RELOAD of IP PBX configuration reload selection for activating the settings. Device configurations on the ATA: STEP 6: Please log in ATA via web browser, browse to the SIP setting menu and select the Domain Service config menu.
  • Page 56 STEP 7: After enabling the auto-config feature, the ATA shall be able to obtain IP address and SIP extension information from IP PBX system IPX-2000 information. To verify the auto-config results, you may connect telephone set to ATA; press #120# to check if the IP address is obtained from IPX-2000.
  • Page 57: Case 5: Call Forward Feature_Example 1

    Case 5: Call Forward Feature_Example 1 In the following samples, we’ll introduce the Call Forward Feature applications. In this example, there are three VIP-156 register to IPX-300 and VIP-156_A had set Call Forward function to VIP-156_B. Machine configuration on the VIP-156: Please log in VIP-156_A via web browser, browse to the Phone Settings menu and select the Call Forward config menu.
  • Page 58 Test the scenario: 1. VIP-156_C pick up the telephone 2. Dial the number 1001(VIP-156_A), 3. Because VIP-156_A had set up All Forward function to the number 2002(VIP-156_B) 4. The number 2002(VIP-156_B) will ring up then it pick up the telephone and communication with the number 3003(VIP-156_C)
  • Page 59: Case 6: Call Forward Feature_Example 2

    Case 6: Call Forward Feature_Example 2 In this example, there are one VIP-157 and two VIP-156 register to IPX-300. The VIP-157_A had set Call Forward function to phone number 1111-2222 (PSTN). Machine configuration on the VIP-157: Please log in VIP-157_A via web browser, browse to the Phone Settings menu and select the Call Forward config menu.
  • Page 60 Test the scenario: 1. VIP-156_C pick up the telephone 2. Dial the number 1001(VIP-157_A) 3. Because VIP-157_A had set up All Forward function to the PSTN Phone Number 11112222 4. The PSTN Phone Number 11112222 will ring up then it pick up the telephone and communication with the number 3003(VIP-156_C)
  • Page 61: Case 7: Call Forward Feature_Example 3

    Case 7: Call Forward Feature_Example 3 In this example, there are one VIP-157 and two VIP-156 register to IPX-300. The VIP-157_A had set Call Forward function to number 2002 (VIP-156_B). Machine configuration on the VIP-157: Please log in VIP-157_A via web browser, browse to the Phone Settings menu and select the Call Forward config menu.
  • Page 62 Test the scenario: 1. PSTN Phone Number 11112222 pick up the telephone 2. Dial the PSTN Phone Number 33334444(VIP-157_A) 3. Because VIP-157_A had set up All Forward function to the number 2002(VIP-156_B) 4. The number 2002(VIP-156_B) will ring up then it pick up the telephone and communication with the PSTN Phone Number 11112222...
  • Page 63: Case 8: Call Forward Feature_Example 4

    Case 8: Call Forward Feature_Example 4 In this example, there are three VIP-156 and connect with Peer to Peer mode. VIP-156_A had set Call Forward function to VIP-156_B. Machine configuration on the VIP-156: Please log in VIP-156_A via web browser, browse to the Phone Settings menu and select the Call Forward config menu.
  • Page 64: Case 9: Auto Answer Feature_Ip To Pstn

    Case 9: Auto Answer Feature_IP to PSTN In this example, there are one VIP-157 and two VIP-156 and connect with Peer to Peer mode. The VIP-157_A had set Auto Answer function for forwarding calls to arbitrary telephone. If there have incoming IP calls and VIP-157_A doesn’t answer the incoming calls after specific time, the caller will hear prompt sounds to input the password then dial out an arbitrary PSTN telephone.
  • Page 65 the Auto Answer config menu. In the setting page, please enable the Auto Answer and PIN Code Enabled function, then the sample configuration screen is shown below: Test the scenario: 1. VIP-156_C pick up the telephone 2. Dial the IP Address 192.168.0.1(VIP-157_A) 3.
  • Page 66: Case 10: Auto Answer Feature_Pstn To Ip

    Case 10: Auto Answer Feature_PSTN to IP In this example, there are one VIP-157 and two VIP-156 and connect with Peer to Peer mode. The VIP-157_A had set Auto Answer function for forwarding to arbitrary telephone. If there have incoming PSTN calls and VIP-157_A doesn’t answer the incoming calls after specific time, the caller will hear prompt sounds to input the password and then dial out an arbitrary IP telephone.
  • Page 67 Test the scenario: 1. The Phone Number 11112222 pick up the telephone 2. Dial the PSTN Phone Number 33334444(VIP-157_A) 3. VIP-157_A will ring up but doesn’t answer the call 4. After 3 rings, the Phone Number 11112222 will hear the prompt sounds then input the password 123# 5.
  • Page 68: Appendix B The Method Of Operation Guide

    Appendix B The method of operation guide In this section, we’ll introduce the features method of operation, and lead you step by step to establish these features. Call Transfer A. Blind Transfer 1. B call to A and they are in the process of conversation. 2.
  • Page 69: Auto Update Firmware By Manual (Keypad)

    the switch code. Realm switch code: 1*: Realm 1 2*: Realm 2 3*: Realm 3 For example: The default is realm 1, input the the telephone set. It will switch to realm 2, and it can make the SIP calls via realm 2. Auto Update firmware by manual (Keypad) If pick up the handsetof ATA, it will hear the “DoDoDo”...
  • Page 70: Appendix C Vip-156/Vip-156Pe/Vip-157/Vip-157S Specifications

    Appendix C VIP-156/VIP-156PE/VIP-157/VIP-157S Specifications Product SIP Analog Telephone Adapter Model VIP-156 Hardware 1 x 10/100Mbps RJ-45 port (802.3af PoE for VIP-156PE) 1 x 10/100Mbps RJ-45 port FXS (for telephone set connection) FXO (PSTN connection) Protocols and Standard Standard SIP 2.0 (RFC3261) Voice codec G.711a/u, G.723.1 (6.3k/5.3k), G.726, G.729A, G.729B, GSM Fax support...
  • Page 71: Ec Declaration Of Conformity

    Manufacturer Authorized representative established within the EU Authorized representative established within the EU (if applicable): Company Name: Planet Technology Corp. Company Address: 11F, No.96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C Person responsible for making this declaration Name, Surname...

This manual is also suitable for:

Vip156peVip-157Vip-156

Table of Contents