Manual Tv Channel Search; Using The Satellite Receiver - Philips turbo drive VR550 Product Manual

HK471BD_EN 4/12/06 6:32 PM Page 5

Manual TV channel search

In some cases it can occur that all of the TV
channels are not found and saved during the first
installation. In this case, the missing or coded TV
channels must be searched for and stored man-
ually.
1.
1. Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.
Press .The main menu will appear.
MENU
3.
3.
Use or
PLAY B-K
SET UP'. Then press
4.
4.
Use or
PLAY B-K
AL TUNING'. Then press
MANUAL TUNING
PROG.
CHANNEL
DECODER
SKIP
SELECT K L CHOOSE B
END=EXIT
5.
5.
Select 'PROG.' with
Then press
FWD 1- B
6.
6.
With or
PLAY B-K
the desired programme number that you want
to use for the TV channel, e.g. 'P01'. Then
press
FWD 1- B
7.
7. Select 'CHANNEL' with
and confirm with
desired channel with
If you set ' SKIP ' on for a channel, this chan-
nel will be ignored when going through the
P +
channels with
I don't know the channels for my TV stations
In this case, press
'CHANNEL' to start the automatic channel
search. A changing channel number will appear
on the TV screen. Continue the automatic search
until you have found the desired TV channel.
8.
8. Save the TV channel with
9.
9.
To search for other TV channels, begin again
at step 5.
10. 10.
To end, press
to select 'TUNER
STOP C-L
.
FWD 1- B
to select 'MANU-
STOP C-L
.
FWD 1- B
P55
055
[OFF]
[OFF]
or
PLAY B-K STOP C-L .
.
, select
or
STOP C-L 0..9
.
or
PLAY B-K STOP C-L
. Then enter the
FWD 1- B
0..9 .
or P– .
or in
PLAY B-K STOP C-L
.
FWD 1- B
STATUS/EXIT .

Using the satellite receiver

Satellite channels from a satellite receiver (con-
nected to the scart socket AV2(DECODER) ) are
received on the video recorder. Select pro-
gramme number 'AV2' with 0.0.2 .
You should select the satellite channels to be
received by the satellite receiver directly on the
receiver itself.
Follow TV
(Automatic TV channels sorting)
When the automatic channel search function is
activated, the TV channels are saved in a specific
order. This may vary from the order of TV chan-
nels on the TV.
This function changes the order of TV channels
saved in the video recorder to match that of the
TV.
Make sure that the video recorder and the TV
are connected by a scart cable.
1.
1.
Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2. Press . The main menu will appear.
MENU
3.
3. Select 'TUNER SET UP' with
and confirm with
STOP C-L
4.
4.
Select 'FOLLOW TV' with
and confirm with
FWD 1- B
,
SELECT K L CHOOSE B
AUTO TUNING
MANUAL TUNING
FOLLOW TV
MOVE
END=EXIT
5.
5. 'P:01' will appear and '01' will flash in the
video recorder display.
6. 6.
Select programme number '1' on the TV.
I cannot switch my TV to programme
number '1'
If you have connected additional devices to
socket AV2(DECODER), please disconnect
these devices. Because of other connected
devices, the TV could switch to the programme
number of the scart socket.
7.
7. Confirm with
FWD 1- B
recorder remote control. The video recorder
compares the TV channels on the TV and the
video recorder.
If the video recorder finds the same TV chan-
nel as on the TV, then it stores it at 'P01'.
5
PLAY B-K
.
FWD 1- B
or
PLAY B-K STOP C-L
.
on the video
EN