Avery Dennison Mobile Work Station (MWS) Monarch 9876 Operating & Maintenance Instructions
Mobile work station
Hide thumbs
Also See for Mobile Work Station (MWS) Monarch 9876:
- Operating instructions manual (20 pages)
Table of Contents
Related Manuals for Avery Dennison Mobile Work Station (MWS) Monarch 9876
Summary of Contents for Avery Dennison Mobile Work Station (MWS) Monarch 9876
- Page 1 Monarch ™ Operating & Operating & 9876™ Mobile Work Maintenance Maintenance Station (MWS™) Instructions Instructions TC9876OI Rev. AJ 12/07 ©2007 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp. All rights reserved.
- Page 2 Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Paxar reserves the right to make changes in the product, the programs, and their availability at any time and without notice. Although Paxar has made every effort to provide complete and accurate information in this manual, Paxar shall not be liable for any omissions or inaccuracies.
-
Page 3: Table Of Contents
Connecting a Printer ........ - Page 4 POWER OPTIONS ........... . . 4-1 Standard or Symbol 24VDC .
-
Page 5: Getting Started
MWS. Describes how to charge the batteries. Describes battery power and battery safety issues. Explains how to print supplies from a printer on the MWS. Technical specifications about the MWS. F a i l u r e t o f o l l o w t h e g u i d e l i n e s m a r k e d w i t h t h i s s y m b o l c o u l d r e s u l t i n s e r i o u s p e r s o n a l i n j u r y o r d e a t h . -
Page 6: Audience
O r d e r i n g P r o g r a m m e r ’ s M a n u a l s The Packet Reference Manual, which describes how to create format and batch packets for printing labels, how to configure a Monarch® printer online, and how to perform other advanced techniques is available from our Web site. -
Page 7: About The Mws
A B O U T T H E M W S The Mobile Work Station ships mostly assembled. This chapter explains the different options and how to assemble any special options, such as the hanging folders. T o o l s Y o u M a y N e e d To assemble the options, you may need a flathead (common) screwdriver;... -
Page 8: Handle Options
H a n d l e O p t i o n s There are different handle configurations and each option is pictured below. One Curved Handle You can have one or two curved handles. Two Curved Handles 2-2 About the MWS... -
Page 9: Shelf Options
S h e l f O p t i o n s You can have one or two shelves. Shelf To collapse the shelf, lift the shelf from the sides and allow it to swing down. To extend the shelf, lift the shelf until the rear lip slides down onto the top of the support brace and locks in place. -
Page 10: About The Doors
A b o u t t h e D o o r s The MWS has combinations of doors and solid panels that do not open. The doors should already be attached to the MWS. Use water or a glass and surface cleaner to clean the doors/panel. -
Page 11: Attaching The Hanging Folders
A t t a c h i n g t h e H a n g i n g F o l d e r s Follow the steps below to attach the hanging folders to the MWS. Doors must be installed before you can use the hanging You must attach the bottom folder to the MWS first. -
Page 12: Connecting The Power Cord
C o n n e c t i n g t h e P o w e r C o r d Make sure to set the proper voltage on the charger voltage selector switch on the right side of the charger (115V in U.S. or 230V International). Incorrect voltage selection can result in charger failure. -
Page 13: Connecting A Printer
Contact your Monarch Representative for instructions on attaching a Monarch® printer to the MWS. U s i n g o t h e r M o n a r c h ® P r i n t e r s Contact your Monarch Representative for instructions on connecting Monarch®... - Page 14 2-8 About the MWS...
-
Page 15: Charging The Batteries
C H A R G I N G T H E B A T T E R I E S This chapter describes how to charge the Mobile Work Station’s batteries change the fuses. The battery charger is a fully automatic, maintenance-free charger. Make sure the voltage selector switch (located on the back of the charger) is set for the proper voltage (115V or 220V). -
Page 16: Important Charging Information
I m p o r t a n t C h a r g i n g I n f o r m a t i o n DANGER! RISK OF ELECTRICAL AND FIRE HAZARD. CERTAIN ACTIONS MAY RESULT IN DEATH, SERIOUS Do not disassemble the battery charger. -
Page 17: About The Battery Charger
A b o u t t h e B a t t e r y C h a r g e r Store the charger in a dry area not subject to prolonged sub-zero temperatures. The battery charger is “intelligent;” it monitors the batteries condition and does not overcharge the batteries. -
Page 18: Battery Life
B a t t e r y L i f e If you leave the battery charger plugged in and constantly charging when the MWS is not in use, the battery life is maximized for the application. The charger will not overcharge the batteries. The MWS has signal lights to indicate the battery status as follows. -
Page 19: Frequency Of Charging/Run-Time Guidelines
(temperature and humidity in your facility or DC). In the information below, “typical conditions” are as follows: one Monarch printer printing standard compliance 4x6 labels (5-10 minutes of actual printing per hour), no auxiliary devices attached to the MWS, and standard environmental conditions (no excessive heat or humidity). -
Page 20: Changing Fuses
C h a n g i n g F u s e s There are two fuses for the MWS: one connecting the batteries and one from BAT2 to the terminal block. Depending on the power option selected when you ordered the MWS, the size of the fuses varies. See Chapter 4, “Power Options,”... -
Page 21: Power Options
P O W E R O P T I O N S Your MWS was ordered with one of these power options: Standard 24VDC Symbol 24VDC 24VDC/115VAC (uses the power inverter for AC power. The power inverter is only 115V.) AC/DC Output with the power inverter. - Page 22 MWS will be unused for extended periods of time, turn OFF the Mobile Work Station’s power switch. The MWS’ power switch controls the power to all printers. If using more than one printer on the MWS, manually turn OFF each printer’s power switch. 4-2 Power Options...
-
Page 23: 24Vdc/115Vac Power Inverter
2 4 V D C / 1 1 5 V A C P o w e r I n v e r t e r The AC power inverter is only 115V. The AC power inverter uses battery power, so the batteries may require more frequent charging. Remove ALL fuses from the cables before connecting ANY cables to the batteries or switch. - Page 24 Make sure the ground wires are attached using one M5 screw with two M4 nuts and M4 washers as shown. Battery Strap Battery Support Ground Wires This equipment contains components which can produce arcs or sparks. To prevent fire or explosion, do not install near Flammable materials or in locations that require ignition-protected equipment (including gasoline-powered machinery, fuel tanks, joints, or fittings).
-
Page 25: Ac/Dc Output (Power Inverter)
A C / D C O u t p u t ( P o w e r I n v e r t e r ) Uses the power inverter for AC power, along with the standard 24VDC for a Paxar/Monarch printer. The power inverter is only 115V. The AC power inverter uses battery power, which may require more frequent charging of the batteries. - Page 26 Check the connections between the inverter’s cables, the batteries and the inverter’s switch as follows: heavy-gauge red cable assembly to positive (+) on BAT2 heavy-gauge black cable to negative (-) on BAT1 orange cable to pole on switch orange cable to Remote (RMT) on switch None of the inverter’s cables are attached the terminal block.
-
Page 27: Inverter Led Status
You may observe a spark when you make this connection since current flows to charge capacitors in the power inverter. Do not make this connection in the presence of Flammable fumes. Explosion or fire may result. Operation of the inverter without a proper ground connection may result in an electrical Do not store anything inside the cabinet other than the batteries and battery charger. -
Page 28: Using The Remote Switch
P r i n t i n g To print supplies from a Monarch printer on the MWS: Turn on the Mobile Work Station’s power supply and turn on the printer. Press Feed/Cut to calibrate the supply. You are now ready to collect data and print. -
Page 29: About Sleep Mode
Escape/Clear, the printer “wakes up” and you enter the offline menu mode. You can also send any data to the printer to wake it up. You do not lose any data sent to the printer during sleep mode. - Page 30 4-10 Power Options...
-
Page 31: Specifications
S P E C I F I C A T I O N S U t i l i t y C a r t Height Approximately 42 inches (1067 mm) depending on selected options Width 23 inches (584 mm) Length 28 inches (711 mm) Weight... -
Page 32: Charger
C h a r g e r Input 117VAC 60Hz, 320VA (Volt Amps) Output 24 Volts, 8 Amps DC Electronic reverse polarity and short circuit-shutdown Low voltage start (total battery voltage must be greater than 1V to charge) AC input fuse in AC input connector Use only NRTL-listed accessories (National Recognized I n v e r t e r Input Voltage... -
Page 33: Wiring Diagrams
Only qualified service personnel may install or replace the two 12-volt sealed lead acid batteries used to power the printer on the Station. If a battery needs to be replaced, BOTH batteries MUST be replaced at the same time to maintain capacity match. - Page 34 S t a n d a r d 2 4 V D C B-2 Wiring Diagrams...
- Page 35 S y m b o l 2 4 V D C Wiring Diagrams B-3...
- Page 36 W M 2 4 V D C ( D C / D C C o n v e r t e r ) B-4 Wiring Diagrams fuse...
- Page 37 2 4 V D C / 1 1 5 V A C P o w e r I n v e r t e r Wiring Diagrams B-5...