Advertisement
Quick Links
9/t~ inch wrench
~ odiustable wrench
inch wrench
¯ hammer
or rubber mallet
inch wrench
¯ s~2 allen wrench
¯ THE PARABODY
FACTOR
625 BASE UNIT MUST BE ASSEMBLED
ON A FLAT, LEVEL SURFACE
TO ASSURE
ITS PROPER
FUNC1
¯ PARABODY
STRONGLY
RECOMMENDS
THAT THIS PRODUCT
BE ASSEMBLED
BY TWO PERSONS
TO AVOID POSSIBLE
INJURY.
,, KEEP ALL FRAME
BOLT CONNECTIONS
LOOSE
UNTIL INSTRUCTED
IN THE ASSEMBLY
STEP SEQUENCES
TO SECURELY
TIGHTi
MAKE SURE SNAP HOOKS
ARE FASTENED
BEFORE
DOING EXERCISES.
NOTE: We recommend
cleaning your produd (pads and the frame members
PoraBody
Customer
Service Representative
at 1-800-328-9714.
on a regular basis, using worm soapy water. Also, touch-up
paint can be purchnsed
from your
BOLT LENGTH
NOTE:
Bolt length ismensured
from the underside
of the head of the bolt.
BOLT LENGTH
RULER:
Advertisement
Related Manuals for ParaBody Leg Press Factor 625
Summary of Contents for ParaBody Leg Press Factor 625
- Page 1 9/t~ inch wrench inch wrench inch wrench ¯ THE PARABODY FACTOR 625 BASE UNIT MUST BE ASSEMBLED ¯ PARABODY STRONGLY RECOMMENDS THAT THIS PRODUCT ,, KEEP ALL FRAME BOLT CONNECTIONS LOOSE MAKE SURE SNAP HOOKS ARE FASTENED BEFORE NOTE: We recommend...
- Page 2 TTS/PARTS: NAME/DESCRIPTION ~(P~78-011 ~--~B0-01 ) Back Pod ~PB3170-01) Leg Press Frame Telescoping Tube Plated ~"-’~43-01) (PB3047-01) [PB3OBI-01) 1 Pivot Axle __ (PB3236-01) l Leg Press Cable 17 ’~ ~634-01) Non-Skid Strip 4" x count all parts before beginning assembly. ’ARE: NAME/DESCRIPTION "...
- Page 3 If you have installed a second weight stack, go to Figure 5. If you have not purchased the second weight stack, please camp]ere the folJowing steps before proceeding to F~gure 1.Remove the blank shroud from the rear of the Factor 625. 2.
- Page 4 ~tinue to route Leg Press cable as shown. ,. ,~emave the boll used to hold the la~ boom 1o ~’he tube an the rear of" lhe Main Frame ~aih one I1) 4~.,~" w/l" Clevis Pulley and one (1) cable retaining clip using one (t) ~-~"...
- Page 5 1. AHach the Leg Press Frame to the Main Frame on lop using two {2) l~"x 41~" Bolts, two (2) 1/2" Washers, two (2) I/2" Lockwashers and two (2) 1,~,, nuts. 2. Attach four (4) 4" x17" Non-Skid Strips to the angled foot pl~e on the Leg Press Frame shown.
- Page 6 ".--~~ble the spring pin assemblT to the ~autum Frame using one (1) knob, one (I) plunger, one (1) spring, one (1) spacer, (1) co~e~ pin, using the folJowing steps: ~ ~semble the knob to the p~ungsr B. In~d the plunger through the fi~ housing and through...
- Page 7 nser~ the seat adjustment tube Into the front end of the Pendulum flame. Pull back the spring pin a~mb/y, and advance the seat adjustment tube If’ al1 the way in. (Make sure tab ai the front end of the seat adiustment tube is up.
- Page 8 . _~.nch the Pendulum Frame to the leg press e by sliding the pivot axle thrnugh the col!ars on the pivot tabs of the leg press flame and through the pivot tube at the top of the pendulum flame. Thread two (2) sA6"...
- Page 9 (2).~/8"x 11/~’~Bohs ock res~ tube on the Pendulum ’ two (2) ~,~" Lockwashe~, Frame using two ana ~o ~2) ~8’ Washe~. NOTE: HOL~ IN ~E BACK OF THE S~T BACK PAD AND ~E S~T PAD. 2. Iflse~ on~ ( ~ ) 2"~quare ~nd cap ( ~ 0-14 g~;)in the top ot ~he back re~ tuoe and one (1) square end cop in the end of the pendulum...
- Page 10 ten any loose connedions at this time. FACTOR 625 should be assembled...