Related Manuals for ParaBody 435103
Summary of Contents for ParaBody 435103
- Page 1 Serious Steel 435103 LEG PRESS ADAPTER. KIT ASSEMBLY INSTRUCTIONS Revision: 09/25/97 Part # 6747801...
- Page 2 2. Do not allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
-
Page 3: Parts List
HOME GYM. See FIGURE 1. PARTS LIST KEY PART# 6535301 3102501 3102802 3102502 3102801 3102933 3102910 (832101) must be assembled before connecthlg PARABODY 425103 t~OME GYM DESCRIP’.rlON 1/4" CAP NUT 3/8" W, HER 3/8" LOCKNUT 1/2" W, HER 1/2" LOCKNUT 3/8X2... - Page 4 FIGURE 2 STEP 2 ¯ If the 445103 SECOND STACK OPTION is not installed, the rear SHROUD opening must be removed. AI?ply pressure to the bottom of the SHROUD where the "V" groove is and carefuly remove the weight stack opening on the SHROUD as shown in FIGURE 3.
- Page 5 2"~ FIGURE 3 ’,TEP 3 ¯ SECURELY attach one 3-1/2" PULLEY (2) to the BASE using one 3/8 X 2" BOLT (14), two 3/8" WASHERS LOCKNUT (11). See FIGURE ¯ SECURELY attach one 3-1/2" PULLEY (2) to the FRONT LEG (1) using one 3/8 X 2" BOLT (14), two 3/8" WASH- ERS (10), and one 3/8"...
- Page 6 FIGURE STEP 5 ¯ SECURELY attach the LEG PRESS to the FRONT LEG (1) using two 1/2" X 3" BOLTS (15), two 1/2" WASHERS 1/2" LOCK NUTS (13). See FIGURE ¯ Route LEG PRESS CABLE (8) around the3-1/2" LEG (1) as shown in FIGURE ~LEG PRESS PULLEY on the LEG PRESS and UNDER the 3-1/2"...
- Page 7 BASE FIGURE 6 STEP 6 ¯ SECURELY attachthe FRONT LEG (1) to 425 BASEusing two 1/2 X 3" BOLTS (15), two 1/2" WASHERS (12) and two 1/2" NUTS (13). See FIGURE ¯ Route LEG PRESS CABLE (8) under the 3-1/2" PULLEY on the 425 BASE as shown in FIGURE...
- Page 8 FIGURE STEP 7 ¯ Run the LEG PRESS CABLE (8) through the correct hole on the d-ring and attach one KEYHOLE LEG PRESS CABLE (8). See FIGURE 7 & DETAIL DETAIL 7 CABLE PRESS CABLE CABLE CABLE CLEVIS (4) to the end of :1/2...
- Page 9 CABLE CABLE CABLE FIGURE 8 CABLE STEP 8 ¯ Attach one TENSION CORD (7) to the KEYHOLE CLEVIS (4) using one CLEVIS PIN (5) and one COTTER PIN (6) as FIGURE 8.
- Page 10 FIGURE 9 BOOM LEG PRESS CABLE STEP 9 ¯ CAREFULLY attach the TENSION CORD (7) to the corresponding small shaft on the TOP BOOM using one 1/4" CAP NUT (9) as shown in FIGURE 9. 1,’2...
- Page 11 To use, you must slightly push against the foot plates to take tension off the pin. Thank you for purchasing the Parabody 435103 Leg Press Adapter Kit. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.