Panasonic Series Hi-Fi NV-HV61 Operating Instructions Manual page 6

If Auto Tuning stops halfway by turning the VCR off or a
power failure,
Or if the VCR is turned on without the aerial connected
and all channels are skipped:
1 Disconnect the mains lead and then reconnect it.
2 Turn off the VCR and then turn it on.
• Auto Tuning commences.
Auto Tuning Using the On Screen Display
Introduction
The VCR is tuned automatically by Plug in Auto Tuning.
However, Auto Tuning using the On Screen Display should be
performed according to the following method if necessary.
Preparations
• Confirm that the TV is on and the VCR viewing channel is
selected.
• Turn on the VCR and select any programme position except
A1 or A2.
Operations
1 Press [MENU] (9) to display the
Main menu on the TV screen.
2 Press [43] (28) to select
[TUNER PRESET] then press
[ENTER] (26).
3 Press [43] (28) to select
[AUTO TUNE] then press [2 1]
(28) to start the Auto Tuning.
• When Auto Tuning is completed,
the On Screen Display
disappears and programme
position 1 is selected.
Channels that can be received
VHF
NV-HV61GL 0-12
NV-HV61GN 1-11
Notes:
• Auto Tuning searches for TV stations from VHF minimum to
UHF maximum and memorizes every tuned programme
position. Other programme positions are skipped.
• Auto Tuning takes 5 or more minutes to complete its search.
MENU
CLOCK SET
TUNER PRESET
SYSTEM
OPTION
TAPE REFRESH
NAVI MEMORY 0 PROG.
SELECT : , ENTER
END : MENU
MENU
CLOCK SET
TUNER PRESET
SYSTEM
OPTION
TAPE REFRESH
NAVI MEMORY 0 PROG.
SELECT : , ENTER
END : MENU
TUNER PRESET
CH 1
[ OFF ]
CLEAR
AUTO TUNE
3
SEARCH [ ]
FINE
SELECT: END : MENU
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
CH 1 SEARCH 100
END : MENU
The number displayed here
is the number of channels
still to be auto tuned.
UHF CATV
28-69 45-470 MHz
21-69 44-470 MHz
Manual Tuning Procedure
If the VCR is not correctly tuned by Auto Tuning, follow the
procedure below.
1 Press [MENU] (9) to display the Main menu on the TV
screen.
2 Press [43] (28) to select [TUNER PRESET] then
press [ENTER] (26).
3 Press [43] (28) to select [CH] then select the channel
number you want to tune by pressing [2 1] (28).
4 Confirm that [CLEAR] is set to [OFF].
5 Press [43] (28) to select [SEARCH] then press [2 1]
(28) to start the Manual Tuning.
• If the desired TV station has not been tuned, press
[2 1] (28) again.
• Press [MENU] (9) and repeat steps 3-5 for each
programme position you want to tune to a station.
CH 2 SEARCH
END: MENU
6 Press [MENU] (9) three times to exit the On Screen
Display.
Direct Tuning
Follow steps 1 to 4 of Manual Tuning Procedure.
5
Press [43] (28) to select [SEARCH].
6
Press [Numeric] (3) to enter the number of the desired
programme position.
For the 5A and 9A channels, input the following
numbers:
90 for CH-5A, 91 for CH-9A. (Example for NV-HV61GL)
• For other channels that require tuning, repeat steps
5 6
3,4, , .
7
Press [MENU] (9) twice to exit the On Screen Display.
Fine Tuning Procedure
Follow steps 1 to 4 of Manual Tuning Procedure.
5 Press [43] (28) to select
[FINE] then press [2 1] (28) to
obtain the best tuning condition.
• Press [ENTER] (26) to return the
tuning to its former state.
6 Press [MENU] (9) to exit the On
Screen Display.
Blanking of Unused Programme Positions
Follow steps 1 to 3 of Manual Tuning Procedure.
4 Press [43] (28) to select [CLEAR] then press
[2 1] (28) to select [ON].
• Repeat steps 3, 4 for other unused programme positions
to skip during the selection of programme positions.
• To cancel the blanking of a programme position, select
that programme position then set [CLEAR] to [OFF].
5 Press [MENU] (9) twice to exit the On Screen Display.
6
CH 2 SEARCH 74
END: MENU
CH 2 AFC: ENTER
FINE : END: MENU