Tuning The Tv To Your Vcr; Storing Tv Broadcasts In Your Vcr - Panasonic Series Hi-Fi NV-HV61 Operating Instructions Manual

Nv-hv61 series video cassette recorder
Hide thumbs Also See for Series Hi-Fi NV-HV61:
Table of Contents

Advertisement

Tuning the TV to Your VCR

The VCR supplies a signal to the TV via the RF coaxial cable
on channel AU28-69 or NZ21-69.
If you have connected the VCR to the TV through the Audio/
Video input sockets, then you do not need to follow the
procedure below. To view the pictures from the VCR, set to
the AV mode on the TV with [AV] (2).
Preparation
• Turn on the TV and the VCR.
Operations
For NV-HV61GN (New Zealand), skip the step 1 and start
from the step 2 because Plug in Auto Tuning starts
automatically.
1 Hold down [MENU] (9) for 5 seconds or more.
2 Set the TV to an unused position which you wish to
use for your video playback.
• Tune the TV until the display shown below appears on
the screen. (Please refer to the TV manufacturers
operating instructions regarding tuning.)
NV-HV61GL/Australia
Panasonic VCR
END: MENU
NV-HV61GN/New Zealand
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
CH 22
SEARCH
21
END: MENU
During Plug in Auto Tuning
3 Press [MENU] (9).
• If Auto Tuning stops halfway, refer to the right, "To Restart
Plug in Auto Tuning".
To Change the RF output Channel
You can change the RF output channel, for example, when
interference occurs on the picture after tuning.
Operations
1 Hold down [MENU] (9) for 5 seconds or more.
• The VCR display changes as shown below and the VCR
picture on the TV displays this pattern.
Panasonic VCR
END: MENU
2 Enter the desired channel number (AU28-69, NZ21-69)
by [Numeric] (3) or [Channel] (20).
• Set the RF output channel of the VCR to [ss] (RF OFF) when
the VCR is connected to the TV via the Audio/Video cable.
Press [Channel] (20) to display [ss].
28
NV-HV61GL:
21
NV-HV61GN:
AUTO TUNING IS
COMPLETED.
END: MENU
After Plug in Auto Tuning
Example for NV-HV61GL
Example for NV-HV61GN
...
69
ss
(RF OFF)
69
ss
(RF OFF)
• It is also possible to select by pressing [Numeric] (3).
Example:
2
28:
3 Press [MENU] (9) to finish the setting mode.
4 Retune your TV to the new RF channel for the VCR.
Note:
• Even if the RF output channel has been changed, it is not
necessary to perform Auto Tuning.

Storing TV Broadcasts in Your VCR

The VCR is fitted with its own tuner (just like a normal TV) and
can be preset to receive up to 99 TV broadcast stations.
Pre-programmed TV Channels
(NV-HV61GL/Australia)
The local TV broadcast channels 2, 7, 9, 10 and 28 are
factory-preset in this VCR.
That is, if you can receive television broadcasts on VHF
channels 2, 7, 9, 10 and UHF channel 28, these are already
tuned on the programme positions with the matching numbers.
However, it is possible to cancel these settings and tune the
local TV broadcast channels to any desired programme position.
Plug in Auto Tuning(NV-HV61GN/New
Zealand)
When the VCR is turned on after connecting the aerial cable
and the mains lead, Auto Tuning starts.
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
CH 22
SEARCH
21
END: MENU
Auto tuning searches for TV stations from VHF minimum to
UHF maximum and memorizes every tuned programme
position.
To Cancel Auto Tuning Mid-Operation:
Press [MENU] (9) during Auto Tuning.
If Auto Tuning stops halfway, follow the next procedures to
restart Plug in Auto Tuning.
To Restart Plug in Auto Tuning:
If Auto Tuning stops halfway by cancelling or playback;
1 Press [EJECT] (35) and remove the video cassette.
2 Keep both [Channel] (20) I and J on the VCR
pressed simultaneously for 3 seconds or more during
the VCR on.
• The channel displayed on the VCR display disappears for
a moment then changes to 1.
3 Disconnect the mains lead and then reconnect it.
4 Turn off the VCR and then turn it on.
• Auto Tuning commences.
5
8

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Nv-hv61glNv-hv61gn

Table of Contents