Related Manuals for Panasonic KX-A272
Summary of Contents for Panasonic KX-A272
-
Page 1: Operating Instructions
DECT Repeater Operating Instructions KX-A272 Model Please read before use and save. -
Page 2: Table Of Contents
Table of Contents Overview ...3 Compatibility...3 General Safety ...3 Environment ...4 Accessories ...4 Wall Mounting ...5 Connection ...5 Placement ...6 LED Status ...6 Automatic Registration ...7 Manual Registration ...8 De-Registration ...10 Verification Tone ...11 Site Survey Mode...12 Serial Repeater ID Programming...13 Before Requesting Help...15 Technical Information ...16 Guarantee ...17... -
Page 3: Overview
The repeater can support up to a maximum of two handsets. Compatibility The Panasonic DECT repeater is:- • Compatible with selected Panasonic consumer DECT products. Please refer to your repeater packaging or your DECT operating instructions for compatibility information. •... -
Page 4: Environment
THE PRODUCT TO RAIN OR ANY OTHER TYPE OF MOISTURE. Accessories (Included) • AC Adaptor PQLV19E (UK only) PQLV19AL (Australian) or PQLV19CE (European) • Repeater KX-A272 • Quick Setup Guide QUQX00112Y • Operating Instructions (on CD-ROM) QUQX00117Y • Screw Pack 4 | Operating Instructions º... -
Page 5: Wall Mounting
Wall Mounting This unit can be mounted on a suitable wall or placed on a flat surface. • Insert screws into wall. Avoid pipes and electrical cables etc. that may be present/buried. The centre of the screws must be 71mm apart. Allow a protrusion of 2mm from the base of the screw head to the wall, using the washer provided (see diagram below). -
Page 6: Placement
• For maximum distance noise-free operation, place your DECT repeater away from electrical appliances such as TV, radio, personal computer or other telephone equipment. • Keep a minimum distance of 10m between repeaters. -
Page 7: Automatic Registration
Automatic Registration Automatic registration cannot be performed if the repeater is already registered to another base unit or cell station. Please follow the DE-REGISTRATION procedure on page 10 before attempting Automatic Registration. • Ensure that the repeater is switched off (disconnect the AC adaptor) (both LEDs are OFF). -
Page 8: Manual Registration
Manual Registration There must be at least one handset already registered to the base unit or cell station to carry out manual registration. • Ensure that the repeater is switched off (disconnect the AC adaptor) (both LEDs are OFF). • Power on the repeater, by connecting the AC adaptor. - Page 9 Manual Registration continued. • Press ‘off hook’ on the handset. The green LED will go steady ON. • Enter a unique identifying number on the handset keypad for each repeater registered. The identifying number can be 2 to 7 for domestic DECT products, and 000 to 255 for PBX DECT products.
-
Page 10: De-Registration
De-Registration In order to perform de-registration, the repeater must have already been registered to a base unit or cell station. • Ensure that the repeater is switched off (disconnect the AC adaptor) (both LEDs are OFF). • While holding down the repeater switch, power on the repeater by connecting the AC adaptor. -
Page 11: Verification Tone
Verification Tone Repeater coverage can be checked by using the in-built verification tone. The coverage area of the repeater can be checked - if the ‘beep’ is no longer heard, then the handset is no longer in range of the repeater. •... -
Page 12: Site Survey Mode
Site Survey Mode (PBX option only) This function can be used to measure the transmission quality, and identify problematic transmission areas of the repeater installation. This function can be used when registered or de-registered. • Ensure the repeater is powered OFF before starting. •... -
Page 13: Serial Repeater Id Programming
Serial Repeater ID programming (PBX option only) This function is used to control up to 3 repeaters in a chain configuration on a PBX system. To ensure correct operation (and to avoid circular linking), each repeater must be assigned a different chain-level (1 – 3). The first repeater (nearest the cell station) is assigned chain-level 1, each additional repeater will then be assigned an incremental number (up to 3), the highest number being assigned to the repeater furthest removed from the cell station. - Page 14 Serial Repeater ID programming continued. • Ensure that the repeater is switched OFF. (both LED’s are OFF) • Power ON the repeater. • Assign the repeater to a base by following either the manual or automatic registration process. • Bring the repeater into close range of the repeater on the parent level (i.e. when assigning a repeater to chain-level 3, the repeater must be brought into close range with the repeater already set to chain-level 2.).
-
Page 15: Before Requesting Help
Before Requesting Help Problem No function (LED not lit) Cannot register (Green LED flashes) or cell station, or base Handset beeping Poor audio quality A ringing call suddenly stops when moving from zone to zone (PBX option only) When talking and moving from zone to condition’, so handover zone, you hear an alarm or continuous... -
Page 16: Technical Information
Technical Information Specifications Standard: Number of channels: Frequency Range: Duplex Procedure: Channel spacing: Bit rate: Modulation: RF Transmission Power: Voice Coding: Operating Range: Power Source: Power Consumption: Operating Conditions: Dimensions: AC adaptor cord length: • Specifications are subject to change •... -
Page 17: Guarantee
8. The guarantee period applicable to this product shall be 12 months. Please keep these Operating Instructions with your receipt. Panasonic Business Systems U.K. Receipt No. Model No. KX-A272E Date of Purchase Serial No. -
Page 18: Index
Index Accessories ...4 Automatic Registration ...7 Before Requesting Help...15 Compatibility...3 Connection ...5 De-Registration ...10 Environment ...4 General Safety ...3 Guarantee ...17 Index ...18 LED Status...6 Manual Registration ...8 Overview ...3 Placement ...6 Serial Repeater ID Programming...13 Site Survey Mode...12 Technical Information...16 Verification Tone...11 Wall Mounting ...5 18 | Operating Instructions... - Page 19 Operating Instructions | 19...
- Page 20 Hereby, Panasonic Communications Company (U.K.) Limited declares that this (KX- A272E) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the manufacturer’s declaration of conformity to the essential requirements of the R&TTE Directive is available at the following web address: http://doc.panasonic.de For your future reference Serial No.