Panasonic NE-2180 Operating Instructions Manual

Panasonic NE-2180 Operating Instructions Manual

2100 watt commercial microwave oven with sonic steamer
Hide thumbs Also See for NE-2180:

Advertisement

R

Operating Instructions

TM
Commercial Microwave Ovens
NE-2180/NE-3280
Please read these instructions completely before operating this oven.
Before Calling for Service:
If failure code "F**" appears in the display, unplug oven and wait for
10 seconds before reconnecting. If normal operation does not resume,
call the service agent with the information of failure code.

Advertisement

Table of Contents
loading

Summary of Contents for Panasonic NE-2180

  • Page 1: Operating Instructions

    Operating Instructions Commercial Microwave Ovens NE-2180/NE-3280 Please read these instructions completely before operating this oven. Before Calling for Service: If failure code “F**” appears in the display, unplug oven and wait for 10 seconds before reconnecting. If normal operation does not resume, call the service agent with the information of failure code.
  • Page 2: Table Of Contents

    Dealer’s Name Dealer’s Address Date of Purchase Contents See page 13 before calling Toll Free Service Information To locate a convenient service agent call 1-888-350-9590 Chef Support: 201-348-7305 www.panasonic.com/cmo Virtual Test Kitchens - 2 -...
  • Page 3: Microwave Energy

    TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY (a) Do not attempt to operate this oven with the door open since open-door operation can result in harmful exposure to microwave energy. It is important not to defeat or tamper with the safety interlocks. Under normal conditions, the oven will not operate with the door open.
  • Page 4: Installation And Grounding Instructions

    Using a lower voltage will lower the power output of the oven, resulting in slower heating of the food. Panasonic is NOT responsible for damage resulting from the use of the oven with other than the specified voltage.
  • Page 5: Power Source Voltage Adjustment

    Power Source Voltage Adjustment Your microwave oven is factory set for 208 V operation. For 220 V - 240 V operation, the following adjustment MUST be made. (Step 1) Unplug the oven. (Step 2) Unscrew the voltage adjustment cover which is located on the back of the oven. Do not remove any other parts from the oven.
  • Page 6: Outline Diagram

    Digital Display Window (see below) Power Level Indicator Display Power Level Selector Pad Memory Shift Pad Memory Pads Stop/Clear Time Pad Start Pad Timer Dial PROG STAGE HI MED LOW This oven is preset at the factory for the following: Manual operation Memory pads preset HIGH power at the indicated heating times for single stage heating 1 = 10 sec.
  • Page 7: How To Operate

    A. MANUAL HEATING Single stage heating This feature gives the user maximum flexibility to set the oven to desired heating times and power levels. Ideal for menus that require variations in heating requirements. Example: To cook food at HIGH power for 2 minutes Open the door and put the food in the oven.
  • Page 8: Or 3 Stage Heating

    2 or 3 stage heating This feature allows you to set to begin heating at one power level then shift automatically to a different power level after designated amount of heating time. Example: To cook food at HIGH power for 2 minutes and at DEFROST power for 1 minute Follow steps 1 to 3 on page 7.
  • Page 9: Programmed Heating

    B. PROGRAMMED HEATING In Program Unlock Mode: MAKE SURE THE UNIT IS PROGRAMMED TO YOUR SPECIFICATION OR NEEDS(see page 10). Example: To select Memory pad “5” on the A side in which your desired heating program (at HIGH power for 3 min., single stage heating) is set Open the door and put the food in the oven.
  • Page 10: Programming Memory Pads

    C. PROGRAMMING MEMORY PADS Single stage heating THE OVEN CAN NOT BE PROGRAMMED WHEN PROGRAM LOCK IS ACTIVATED! (see page 11) DO NOT OPEN THE DOOR WHILE PROGRAMMING! Example: To program cooking on DEFROST power for 1 minute into Memory pad “5” Keep the door closed.
  • Page 11: Or 3 Stage Heating

    2 or 3 stage heating THE OVEN CAN NOT BE PROGRAMMED WHEN PROGRAM LOCK IS ACTIVATED! (see below on this page) DO NOT OPEN THE DOOR WHILE PROGRAMMING! Example: To program cooking at DEFROST power for 1 minute and at HIGH power for 2 minutes into Memory pad “5” Follow steps 1 to 5 on page 10.
  • Page 12: Beep Tone

    E. BEEP TONE The loudness of beep tone and its duration at the end of heating cycle can be set. There are four levels of the loudness and two levels of duration. The loudest level and 3 beeps are preset at the factory. To select loudness level and length “3 beeps”: Press Program Entry Button.
  • Page 13: G.cycle Counter

    G. CYCLE COUNTER Read Total Cumulative Times That The Oven Has Been Used: Open the door and leave it open. The oven lamp will turn on and “0” will appear. Close the door. Carry out Step 3 within 60 seconds of closing the door, or the display will go blank.
  • Page 14: Sanitary Counter Top Seal

    Sanitary Counter Top Seal When microwave oven is placed on a counter top, its base must be sealed in accordance with N.S.F. Standards as per the following instructions. 1. Microwave oven should be located on a level counter top surface. Complete the electrical connections.
  • Page 15: Cooking Instructions

    7. Heated liquids can erupt if not mixed with air. Do not heat liquids in your microwave oven without first stirring. (See #1) Recipes available on www.panasonic.com/cmo GENERAL GUIDELINES FOR STEAMING IN A PANASONIC SONIC STEAMER Please refer to the USDA/FDA Food Code guidelines.
  • Page 16: Technical Specifications

    Specifications subject to change without notice. 25 / " 18 / " " " www.panasonic.com/cmo PANASONIC HOME AND COMMERCIAL PRODUCTS COMPANY, DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA One Panasonic Way 4A-4 Secaucus, NJ07094 Or Call (201) 348-5377 NE-3280 208/230 V, 60 Hz., single phase 28.0 A (208 V)

This manual is also suitable for:

Ne-3280

Table of Contents