Summary of Contents for Audiovox PRESTIGE APS-20LAD
Page 1
Vehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions This Unit Is Intended For Installation In Vehicles With 12 Volt Negative Ground Electrical Systems Only (2) - Two Button Transmitters 2 Channel Code Learning Receiver (1) - Multi Pin Input/Output Harness (1) - Two Pin Door Lock Harness (1) - Two Pin Valet / Programming Switch Released 9-24-99.
Page 2
The APS-20LAD Vehicle Alarm System is designed to provide a basic deterrent to vehicle theft, and a convenient electronic means to gain access to the vehicle by providing RF remote control over the vehicle's power door lock system. The unit also includes outputs to control the vehicle's parking lights, and an additional auxiliary output designed to allow for control over an optional device such as a power trunk release or engine starting device.
extended when the hood or trunk is opened. For direct mounting, a 1/4 inch hole must be drilled. Carefully check behind the chosen location to insure the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the desired location and thread the pin switch into it using a 7/16"...
Page 4
hatch is opened, and vice-versa. If only the hood, or only the trunk/hatch is connected to the Dark Green wire, no diode is needed. Note: The diodes which may be required for certain types of installations are the common 1N4000 series type. You may chose to use any of the diodes in this series, with the 1N4003 and 1N4007 being the most common types.
In these applications, the AS-9159 Door Lock Interface (or equivalent 30 Amp. automotive type relays) must be used. Refer to the Audiovox Door Lock Wiring Supplement for proper connection to these types of circuits. PLUG-IN CONNECTIONS AND COMPLETING THE INSTALLATION: Now that all the other components have been installed, and most of the main connections completed, it is time to finish connecting the remaining plug-in components and completing the installation.
connector, it will only plug in one way. Note: Please refer to the section; "Programming System Features" shown later in this installation guide to learn the operation of the valet/program/manual override switch. POWER DOOR LOCK HARNESS 2-PIN White Plug w/2 Wires; Red & Green The connection of the power door lock/unlock wires has already been explained.
to produce 2 Chirps. This signifies that you have changed the programming to Chirps OFF. Please follow the programming procedure carefully, and refer to the list of the Programmable Features above when programming the APS-20LAD. FEATURE ACTION TO PERFORM Turn the Ignition Switch ON Enter Toggle the Valet/Program/Manual Override Switch ON then OFF 3 Times...
Page 9
Modelo APS-20LAD Manual de instalación Sistema de alarma para vehículo con salida auxiliar por canal 2 Instrucciones de instalación Esta unidad se puede instalar en vehículos con sistemas eléctricos con conexión a tierra negativa de 12 voltios solamente Contenido del kit: Módulo de control APS-20LAD (2) - Transmisores de llavero con dos botones Receptor con captación de código de 2 canales...
Page 10
El sistema de alarma para vehículos APS-20LAD está destinado a brindar un elemento de disuasión contra robo de vehículos y un medio electrónico conveniente de tener acceso al vehículo mediante un control remoto de RF para el sistema eléctrico de trabado de las puertas del vehículo.
Page 11
diferente en el arnés. Cada uno de estos portafusibles sostiene un fusible ATC, uno de 5A y otro de 15A. Este cable ROJO debe ser conectado a un cable de energía constante del arnés o de la caja de fusibles del interruptor de encendido del vehículo. La mayoría de los vehículos tiene por lo menos un cable proveniente de la batería que suministra energía eléctrica al interruptor de encendido.
Page 12
Cable NEGRO: Sistema principal de conexión a tierra Este es uno de los cables más importantes de la instalación del sistema APS-20LAD. Debe conectarse correctamente a una parte sólida del chasis para asegurar el funcionamiento seguro del sistema. Elija cuidadosamente una parte metálica limpia y sólida del chasis como punto de conexión para este cable.
Page 13
En estas aplicaciones, se debe usar la interfaz de trabado de puertas AS-9159 (o relés para automóviles de 30 A equivalentes). Consulte del Suplemento de Cableado para trabado de puertas de Audiovox para obtener información sobre el cableado correcto de estos circuitos.
Page 14
Funciones programables: Funciones 1 chirrido Primera Activación pasiva Segunda Encendido D/L “on” Tercera Encendido D/UL “on” Cuarta Pasivo D/L Quinta Chirridos “on” Función Acción Encienda la llave de contacto. ON Para Mueva el interruptor valet/programación/ entrar al captura manual a la posición “ON” y modo de luego “OFF”...
Para programar estas funciones: La entrada al Modo de programación involucra el uso del interruptor o llave de contacto y el interruptor valet / programación / captura manual en una determinada secuencia, la que depende mucho de la rapidez con que se haga, es decir, tiene que realizarse rápidamente para que pueda entrar al modo.