Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Panasonic TX-47P600HZ
Summary of Contents for Panasonic TX-47P600HZ
-
Page 1: Operating Instructions
Wide Projection Television Operating Instructions TX-47P600H Model No. This is a combined Operating Instruction manual for all the above series of models. Please read these instructions before operating your set and retain them for future reference. TQBC0532... -
Page 2: Important Information
Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Wide Projection television set. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. -
Page 3: Table Of Contents
Table of contents Table of contents Warnings and Cautions ... 4 Before Operating This Set ... 6 Safety Precaution / Securing the casters ... 6 Connecting the Plug to the Wall Outlet ... 6 How to Turn the Power On ... 6 Battery Installation ... -
Page 4: Warnings And Cautions
Warnings and Cautions Warnings Unplug the power cord in the e v e n t o f a n y m a l f u n c t i o n (screen goes blank, no sound, odd sounds, smoke or unusual odors coming from the unit). - Page 5 Cautions DO NOT place in humid or d u s t y l o c a t i o n , o r a r e a s exposed to smoke or steam. D O N O T p l a c e i n d i r e c t sunlight and other sources of direct heat.
-
Page 6: Before Operating This Set
Before Operating This Set Safety Precaution Please take safety precautions to prevent the unit form falling over. The unit may fall over during earthquakes, or if someone stands on or shakes the TV. Fixing to a wall Use a strong rope or a chain to fasten the TV firmly to a strong support such as a wall or a pillar. -
Page 7: Battery Installation
Battery Installation Open the cover. Apply slight downward pressure while pulling towards the bottom. Do not use rechargeable (Ni-Cd) batteries. They are different in shape and performance and may fail to ensure correct operation. Battery cautions The incorrect use of batteries can cause electrolyte leakage which will corrode the Remote Control or cause the batteries to burst. -
Page 8: Location Of Controls
Location of Controls Controls and Terminals on the TV Item Function Main Headphones Jack Sub Headphones Jack AV3 Input Terminals Function Volume Down ( ) / Programme Number Down ( ) Volume Up (+) / Programme Number Up ( ) Main TV/AV MONITOR... -
Page 9: Connections
Connections Connecting the Aerial Cable to the RF In Terminal VHF Aerial UHF Aerial Mixer 75 Ohm Coaxial Cable RF In Terminal Notes: • To obtain optimum quality picture and sound, an Aerial, the correct cable (75 Ohm coaxial) and the correct terminating plug are required. -
Page 10: How To Connect The "Av1, 2, 3 Or 4" Input Terminals
Connections How to connect the “AV1, 2, 3 or 4” Input Terminals Connect VCRs and other peripheral equipment (VHS VCR) Audio Video VIDEO AUDIO (Super-VHS VCR) Audio Video S Video VIDEO AUDIO Notes: • When an S Video cable is connected to the S Video terminal, the corresponding Video input will be switched off and the signal from the S Video input will be used. -
Page 11: How To Connect The Dvd Input Terminals
How to connect the DVD Input Terminals DVD Player Audio DVD( Y-P ) OUT Notes: • The AV4 audio signal is common for both AV4 and DVD input signal terminals. • The DVD signal input terminal takes priority over the AV4 video signal input terminal. •... -
Page 12: General Operation
General Operation Power switch Used to store tuning and other function settings. Also used to start the menu demonstration. Function selection Displays the on screen display functions, use repeatedly to select from the available functions. The following adjustments can be accessed directly. VOLUME TUNING MODE CONTRAST... - Page 13 Power (Stand-by) (see page 7) The TV set must first be plugged into the wall outlet and turned on at the power switch. Press this button to turn the TV set On from Standby mode, Press it again to turn the TV set OFF to Standby mode.
-
Page 14: On-Screen Menu Display From Remote Control
On-Screen menu Display from Remote Control To PICTURE adjust menu (see page 26) PICTURE MENU STANDARD CONTRAST BRIGHTNESS COLOUR SHARPNESS NTSC-TINT C. TEMP STANDARD PICTURE P-NR AUTO SCAN MODE AUTO To SOUND adjust menu (see page 28) SOUND DYNAMIC MENU VOLUME BASS TREBLE... - Page 15 On-Screen menu Display from Remote Control To SETUP MENU (see page 25) SETUP MENU TELETEXT OFF TIMER FLICKER REDUC. DYNAMIC STROBE CH COLOUR SET VCR / GAME TEXT SELECT ENGLISH SETUP MENU CHILD LOCK PICTURE SHIFT ACCESS TUNING MENU CONVERGENCE LANGUAGE ENGLISH SETUP MENU...
-
Page 16: Convergence Adjustment
Convergence Adjustment Convergence Adjustment mode SET UP Prior to adjustment, tune the broadcast signal to the video input signal and operate the set for more than 60 minutes. If the location or direction of the set is changed or moved, the display may be out of alignment. -
Page 17: Convergence1 Adjustment For Red, Blue And Green
Convergence1 Adjustment for RED, BLUE and GREEN Press to align the horizontal red line with the horizontal blue line. (Becomes a white line) Press to align the vertical red line with the vertical blue line. (Becomes a white line) Press BLUE Press to align the horizontal blue line with the horizontal yellow line. -
Page 18: Convergence2 Adjustment For Red And Blue
Convergence Adjustment Convergence2 Adjustment for RED and BLUE This function adjust the convergence of the side part of the screen. Press to select the CONVERGENCE2. Press to access to the function. TV/TEXT INDEX HOLD F.P. 100Hz/ CH SEARCH STILL PROGRE SURROUND ASPECT MULTI... -
Page 19: Tuning Channels
Tuning Channels Display the TUNING MENU SET UP Regional System Selection SYS SELECT (Before AUTO tuning and MANUAL tuning, set the “SYS SELECT” mode, as detailed below.) CHINA HK/UK JAPAN CATV System Select by Regional SYSTEM SELECT CHINA China HK / UK Hong Kong, United Kingdom ASIA/M.EAST Malaysia, Singapore, Thailand, Asia countries, Kuwait, Saudi Arabia, United Arab Emirates, Middle East countries, etc. -
Page 20: Automatic Tune
Tuning Channels Automatic Tune This TV uses automatic tuning to determine whether or not the TV can receive a broadcast signal which is being sent. Before Automatic Tune, Regional System must already be set (Refer to pages 19). AUTO TUNE SOUND SYS After all stations are tuned, the on-screen display will automatically change from “AUTO TUNE”... -
Page 21: Manual Tune
Manual Tune Before Manual Tune, Regional System must already be set (Refer to page 19). MANUAL TUNE TV/AV SOUND SYS SET UP Adjust the Sound System ( refer to page 20 step 2 to 3). Helpful Hint (1) If a clear picture with correct colours cannot be obtained when a Broadcast or AV signal is received, refer to the “Colour System Selection”... -
Page 22: Fine Tuning
Tuning Channels Fine Tuning Under normal reception conditions this function is not required or necessary. However, in areas of poor reception or constant interference, a slight adjustment of the tuning may improve the picture and sound quality. Press to select the FINE TUNE. Press until the clear picture is received. -
Page 23: Programme Number Skip
Programme Number Skip It is possible to skip Programme Number on which no TV stations are tuned appearing on the screen. The function is only effective when selecting Programme Numbers by pressing the Programme Number Up or Down button either on the TV set or on the Remote control. -
Page 24: Sound System Selection (Different Region Use Differing Systems)
Tuning Channels Sound System Selection This function is used only in the TV mode when the sound is not clear or no sound is produced on a Programme Number, and is not applicable in AV mode . Press to select the “SOUND SYS”. Press until the optimum sound is obtained. -
Page 25: Setup Adjustment
Setup Adjustment SET UP TV/AV OFF TIMER Switches the TV off within a preset time which you can choose from between 0 to 90 minutes in 15 minutes intervals. FLICKER REDUCTION Lets you control any picture movement. Set to Dynamic to activate motion compensation, to smooth the image and get rid of picture movement. -
Page 26: Picture Adjustment
Picture Adjustment PICTURE TV/AV MENU Picture menu mode will be memorized for each TV, AV1, AV2, AV3 and AV4 mode. • You can change the level of each Item (CONTRAST, BRIGHTNESS, COLOUR, SHARPNESS and NTSC-TINT) for each Picture Menu (DYNAMIC, STANDARD and SOFT). - Page 27 C. TEMP Set the overall colour tone of the picture. (Colour Temperature) Press to switch between modes Automatically reduces undesired picture noise. P-NR (Picture Noise Reduction) Press to switch between modes Automatically analyses the incoming picture and processes it to give improved contrast and (Artificial intelligence) optimum depth of field.
-
Page 28: Sound Adjustment
Sound Adjustment SOUND TV/AV Note: Some features are only available with the Surround feature switched off. Press MENU Sound menu mode will be memorized for each TV, AV1, AV2, AV3 and AV4 mode. • You can change the level of each Item (VOLUME, BASS, TREBLE, BALANCE, HEADPHONE VOL and SUB HEADPHONE) for each Sound Menu (DYNAMIC, STANDARD and SOFT). - Page 29 SURROUND MENU SURROUND Press to switch between ON and OFF. SURROUND SOUND Press to display the Sound Menu. Press to select the SURROUND function. Press to switch between ON and OFF. The benefits of surround sound are enormous. You can be completely enveloped in sound; just as if you were at a concert hall or cinema.
-
Page 30: Aspect Controls
Aspect Controls ASPECT INDEX HOLD TV/TEXT F.P. 100Hz/ CH SEARCH STILL PROGRE SURROUND ASPECT Notes: MULTI • Simply press • 16:9 picture has been used to illustrate all of the aspect modes described in this section. The on screen selector keys (corresponding to the four coloured buttons on the remote control) appear for some Aspect functions and disappear after a few seconds. - Page 31 Mode AUTO 4 : 3 JUST 16:9 Signal 4 : 3 ZOOM S-ZOOM 16 : 9 16:9 Signal 14 : 9 JUST Note: ASPECT operations cannot be made during progressive (Y, P Picture 4 : 3 JUST 4:3 Signal ZOOM V SIZE—...
-
Page 32: Multi Screen
Multi Screen Multi PIP Press and picture feature. PICTURE The on screen selector keys for the features (corresponding to the four coloured buttons on SOUND the remote control) appear and disappear after a few seconds. If you would like to select an operation when the keys are not shown, press SET UP TV/AV... -
Page 33: Channel Search
Picture and text TV/TEXT Press to select watching the current programme, the teletext or the picture and text feature. Note: The remote control affects the teletext page; so select watching the current programme before making any changes to the programme. Still HOLD Press to freeze the picture, press again to return to watching the current programme. -
Page 34: Tele Text
TELE TEXT Teletext features may vary depending on the Broadcasting Companies and are only available when the channel selected is transmitting Teletext. Select character set, so that all characters needed TEXT SELECT are available for text on teletext pages (eg: cyrillic characters, etc). - Page 35 Page Selection (Two ways) Press to increase or decrease the page number by one. FulI / Top / Bottom SET UP Press to display special functions. Press the Green button to expand the Top half. Green Press again to expand the Bottom half. Press again to return to normal (FULL) size.
- Page 36 TELE TEXT Teletext page Press to display special functions to view the TV picture whilst searching for a Teletext page . SET UP P100 Yellow When found a page. Press to view the page. Yellow Return to normal TV operation. Index INDEX Press to return to the main index page.
-
Page 37: Advanced Remoto Control Operation
VCR / LD / DVD Control The Remote Control is capable of operating some functions of selected Panasonic VCRs, LD and DVD (Digital Versatile Disc) equipment. Some VCR, LD and DVD equipment have different functions. So to ensure compatibility please refer to the equipment's instruction book or consult your dealer for details. -
Page 38: Manufacturer Setting
Press to select VCR or LD /DVD. While pressing the VCR / LD / DVD Power button, press the manufacturer code (enter the two digit code), and press the VCR / LD / DVD Stop button. Manufacturer Panasonic/ National AIWA FUJITSU HITACHI MITSUBISHI... -
Page 39: Troubleshooting
Troubleshooting Before you call for service, determine the symptoms and make a few simple checks as shown below. Symptoms Picture Snowy Picture Multiple Image Interference Normal Picture No Picture No Colour Scrambled Coloured Patches No Colour Projection TV screen Symptoms Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to remain on the Wide Projection TV screen. -
Page 40: Cleaning
Cleaning To ensure continued excellent performance by this product, periodic cleaning is recommended. The unit contains many plastic parts. For this reason DO NOT use benzine, thinner or other chemicals to clean the unit. DO NOT bring into contact w i t h i n s e c t i c i d e o r o t h e r volatile substances. -
Page 43: Specifications
Specifications Power Source Power Consumption Remote control Transmitter Dimensions ( W H D ) Mass (Weight) Receiving System 21 Systems PAL B, G, H PAL I PAL D, K SECAM B, G SECAM D, K SECAM K1 NTSC M (NTSC 3.58/4.5 MHz) NTSC 4.43/5.5 MHz NTSC 4.43/6.0 MHz NTSC 4.43/6.5 MHz... - Page 44 Warranty Service purposes. Model Number Matsushita Electric Industrial Co., Ltd. Printed in Japan MBS0802O0 Serial Number Web Site : http://www.panasonic.co.jp/global/...