Download
Share
Print this page
Audiovox Prestige MA200C Installation Manual And Owner's Manual
  1. Manuals
  2. Brands
  3. Audiovox Manuals
  4. Security System
  5. Prestige MA200C
  6. Installation manual and owner's manual
Audiovox Prestige MA200C Installation Manual And Owner's Manual

Audiovox Prestige MA200C Installation Manual And Owner's Manual

Remote control motorcycle alarm system
Hide thumbs

Advertisement

Quick Links

Download this manual
MODEL MA200C
REMOTE CONTROL
MOTORCYCLE ALARM SYSTEM
INSTALLATION GUIDE
AND
OWNERS MANUAL
1

Advertisement

loading

Related Manuals for Audiovox Prestige MA200C

Summary of Contents for Audiovox Prestige MA200C

  • Page 1 MODEL MA200C REMOTE CONTROL MOTORCYCLE ALARM SYSTEM INSTALLATION GUIDE OWNERS MANUAL...
  • Page 2 Congratulations on the purchase of your new Audiovox Alarm System. Taking a few minutes to read this installation and owners guide will provide you with the detailed information concerning all the features of your new alarm system. MOUNTING THE SIREN/CONTROL MODULE 1.
  • Page 3 BLACK (LONG): Using the attached wire lug, connect the Black (long) wire of the siren to the negative terminal of the battery or a good ground source. BLACK (SHORT): Stretch the short Black antenna wire as long as pos- sible, avoiding metal contact if possible. This is the an- tenna wire for the alarm system;...
  • Page 4 SHEET METAL RELAY RELAY WIRE TIE TO EXISTING FIGURE 3 To + or - as required by Horn Fuse if positive White/Black To fused 12V constant source CONNECTING THE RELAY (HORN FEATURE) IMPORTANT! The relay has been shipped with the BLACK wire loaded into terminal 87a of the Relay Socket.
  • Page 5 CONNECTING THE RELAY (STARTER/IGNITION) IMPORTANT ! When using the relay to disable the starter, leave the BLACK wire in ter- minal 87a of the relay connector in the location shown in the Figure 5. 1. Connect the ORANGE wire from the relay harness to the ORANGE wire from the siren harness.
  • Page 6 To Bike Harness To fused 12V constant source CONNECTING THE RELAY (HEAD LAMP FLASH FEATURE) IMPORTANT! When using the relay to flash the vehicle’s parking lights, unload the BLACK wire from terminal 87A of the relay harness and load it into terminal 87.
  • Page 7 2. Turn the ignition "ON" then "OFF" 5 times. The system will sound a long chirp to confirm entry into the program mode. 3. Press the "LEFT" button of each transmitter to be programed (up to Two Transmitters). The siren will chirp to confirm each transmitter is now programmed.

  • Page 8: Operating The System

    NOTE: If the alarm issues three warnings within 15 seconds, the siren will sound a regular alarm tone which lasts for 30 seconds. After 30 seconds, the siren will automatically stop and the alarm will arm itself. OPERATING THE SYSTEM Operation of the system is described in this section.
  • Page 9 To activate the panic feature: 1. Press and hold button 1 on the keychain transmitter for 3 seconds. 2. The alarm will sound, and continue to sound for 30 seconds. 3. To silence the alarm before the 30-second shut- down, press and hold button #2 on the keychain transmitter.
  • Page 10 Replacing the Transmitter Battery The keychain transmitters have a small, red LED visible through the top cover. This LED can be used to indicate battery condition. You will also notice a decrease in effective transmitter range as the battery deteriorates. The replacement battery must be a 12 volt type GP27A or equivalent.

  • Page 11: Troubleshooting

    Symptom: The Transmitters will not program to the control module. Check: 1. Verify that the 1 Amp fuse in the red wire from the siren control module is in good condition. Replace it if it is blown. 2. Verify that the connections of the red and black wires have been made according to the wiring section of this manual.
  • Page 12 V is it O u r W eb site A t P rod uct In form a tion , P h otos, FA Q ’s O w n er ’s M a n ua ls © 2002 Audiovox Electronics Corp., Hauppauge, NY 11788 128-6276...