31939_KX-TCD700CX_Czech 18/6/01 1:54 pm Page 1 Digital Cordless Phone KX-TCD700BX Model No. Operating Instructions Caller ID Compatible PLEASE READ BEFORE USE AND SAVE Charge the batteries for approx. 10 hours before initial use.
Page 2
31939_KX-TCD700CX_Czech 18/6/01 Dear purchaser, You have acquired a KX-TCD700BX, which is a product made in regard with the European Standards for Cordless Telephones (DECT). DECT technology is characterized by high-security protection against interceptions as well as high-quality digital transmission. This telephone was designed for a wide range of applications.
31939_KX-TCD700CX_Czech 18/6/01 Safety Instructions Take special care to follow the safety suggestions listed below. Environment 1) Do not use this unit near water—for example, near a bathtub, washbowl, sink, etc. Damp basements should also be avoided. 2) The unit should be kept away from heat sources such as radiators, cookers, etc. It also should not be placed in rooms where the temperature is less than 5°C or greater than 40°C.
31939_KX-TCD700CX_Czech 18/6/01 Contents Chapter 1 Preparation Getting Started ...6 Connections...6 Installing the Batteries in the Handset ...7 Battery Charge ...7 Battery Information ...7 Battery Replacement ...8 Base Unit Location ...8 Wall Mounting...9 Location of Controls...10 Displays ...11 Basic Start-up Operations ...12 Chapter 2 Basic Operations Making Calls...13...
Page 5
31939_KX-TCD700CX_Czech 18/6/01 Chapter 4 Programmable Functions (On the Base Unit) Programmable Functions (On the Base Unit) ...40 Bell Selection...40 Select Base Unit Ringer Volume ..41 Select the Dialling Mode ...41 Setting the Clock ...41 Select Earth/Flash Mode ...42 Select Pause Timing...42 Set Base Unit PIN ...43 Cancelling a Handset ...43 Reset Base Unit ...45...
USE ONLY WITH Panasonic AC ADAPTOR PQLV1CE. • Be careful not to confuse the telephone line jack with the AC adaptor jack on the Base unit. If connected improperly, the base unit will not work and damage may occur.
31939_KX-TCD700CX_Czech 18/6/01 Installing the Batteries in the Handset • If the rechargeable batteries are not inserted correctly, the handset will not work. Battery Charge At the time of shipment, the batteries are not charged. To charge, place the handset on the base unit.
31939_KX-TCD700CX_Czech 18/6/01 ➡ Getting Started Battery Caution: To reduce the risk of fire or injury to persons, read and follow these instructions. 1. Use only the batteries specified. 2. Do not use non-rechargeable batteries. 3. Do not mix old and new batteries. 4.
31939_KX-TCD700CX_Czech 18/6/01 1:54 pm Page 9 Wall Mounting This unit can be mounted on a wall. • Install screws using the wall template below. • Connect the line cord, and AC Adaptor. • Arrange the wires as shown, then mount the unit. WALL TEMPLATE...
31939_KX-TCD700CX_Czech 18/6/01 Displays Handset Display Icons The in-range icon indicates that the handset is in range of the base unit. It flashes when the handset is out of range. The page/intercom icon is displayed when paging or using the intercom. It flashes when another unit pages the handset.
31939_KX-TCD700CX_Czech 18/6/01 Basic Start-up Operations Turning the Power On and hold • After all characters briefly appear a confirmation tone sounds. The display will change to the standby mode when the button is released. • The current connected base unit number is displayed ( •...
31939_KX-TCD700CX_Czech 18/6/01 Making Calls Note: for basic making calls operation, see page 12. To Dial after Confirming the Entered Number With this feature you are able to confirm the entered number before you start dialling. 1. Dial a Phone Number If number is not entered correctly: To clear one digit, To clear all digits,...
31939_KX-TCD700CX_Czech 18/6/01 ➡ Making Calls To Edit/Clear Numbers in the Redial List To edit and clear numbers in the redial memory, press then follow from step 2 (page 20). Direct Call You can store one number into memory and then call this number by pressing Incoming calls are accepted.
31939_KX-TCD700CX_Czech 18/6/01 Answering Calls For basic answering call operation, see page 12. • The handset and base unit will not ring if both ringer volumes are set to OFF (p. 29, 41) Auto Talk If you set the Auto Talk Feature to ON (p. 34), you can answer a call by lifting the handset off the base unit without pressing To Turn the Handset Ringer Off Temporarily When an external call is incoming, user can turn off ringer...
31939_KX-TCD700CX_Czech 18/6/01 Speed Dialling Storing Phone Numbers in Memory You can store up to 20 telephone numbers in the handset Storing new numbers (Speed dial is selected, speed dial icon is displayed 3. Enter phone number (Up to 24 digits) (Phone numbers are displayed from the left edge of the LCD).
Page 17
31939_KX-TCD700CX_Czech 18/6/01 Speed Dial Menu In the speed dial menu, it is possible to carry out the following operations: • Edit a speed dial number ( • Clear a speed dial number ( • Register a speed dial number to Hot Key ( (Standby Mode) •...
Page 18
31939_KX-TCD700CX_Czech 18/6/01 ➡ Speed Dialling Saving Numbers in Speed Dial List ( Telephone numbers can be saved into the speed dial list from other lists eg. Caller ID list, re-dial list, etc. To save a number from other lists; 1. Display number to be saved “...
31939_KX-TCD700CX_Czech 18/6/01 Caller ID Service Caller ID, where available, is a telephone company service. After subscribing to Caller ID, this phone will display the caller’s phone number. This unit is compatible with a Caller ID service offered by your telephone company.
Page 20
31939_KX-TCD700CX_Czech 18/6/01 ➡ Caller ID Service Caller ID Sub-Menu In the Caller ID sub-menu, it is possible to carry out the following operations: • Save a Caller ID Number to speed dial list ( • Edit a Caller ID Number ( •...
31939_KX-TCD700CX_Czech 18/6/01 Using the Caller List Viewing the Caller List Telephone numbers of up to 50 different callers are stored from the most recent to the oldest call in the Caller List. When the 51st call is received, the oldest call is deleted.
• The optional handset/charger model number is KX-A114EX. The functions of the optional handset are the same as those of KX-TCD700BX handset. • To register a handset to a base unit, see page 36.
31939_KX-TCD700CX_Czech 18/6/01 Paging/Intercom Paging All Handsets from the Base Unit (On the Base Unit). • All handsets will ring for one minute. 2. To stop paging, Intercom between Handsets A 2-way intercom is available between handsets. Eg. Handset 1 is paging Handset 2 1.
Page 24
31939_KX-TCD700CX_Czech 18/6/01 ➡ Paging/Intercom Transferring a Call using the Intercom 3. (Handset 2) When the unit rings, 4. (Handset 1) Transferring a call • The transfer is completed to return to the External Call Transferring a Call without the Intercom This feature enables you to transfer the call to another handset without waiting for the paged handset to answer.
31939_KX-TCD700CX_Czech 18/6/01 Special Features How to Use the Pause Feature (For Analog PBX Line/Long Distance Service Users) We recommend you insert “ access a long distance service. (When Eg. Line access number and then phone number. (After a few seconds, display will start showing the length of the call). •...
31939_KX-TCD700CX_Czech 18/6/01 ➡ Special Features Setting the Key Lock (ON) You can lock the handset dialling buttons. Only incoming calls are accepted until the key lock is cancelled. You can answer a call by pressing any dialling button (-Any Key Answer). Make sure that the unit is in the standby mode.
31939_KX-TCD700CX_Czech 18/6/01 Summary of Programmable Functions On the Handset You can program the following function items using the handset near the base unit. See the corresponding pages for function details. (Standby Mode) Refer to relevant page as indicated. • • •...
31939_KX-TCD700CX_Czech 18/6/01 Setting Time Alarm Function Within the Time Alarm menu, it is possible to program the following: • Set Time of Alarm ( • Set Alarm ON/OFF ( to once ( ), repeat daily ( (Standby Mode) To Stop the Alarm When the alarm sounds, press any dialling button •...
31939_KX-TCD700CX_Czech 18/6/01 Setting Ringer Options Within the Ringer Option menu, it is possible to program the following: • Select the Handset Ringer Volume ( OFF ( • Select the Ringer Pattern for External Incoming Call ( • Select the Ringer Pattern for Internal Call ( •...
31939_KX-TCD700CX_Czech 18/6/01 Setting Tone Options Within the Tone Option menu, it is possible to program the following: • Set Key Confirmation Tone ON/OFF ( You can choose whether or not the handset keys will sound tones (eg. key tone, confirmation tone, error tone). •...
31939_KX-TCD700CX_Czech 18/6/01 Setting Display Options Within the Display Option menu, it is possible to program the following: • Select the Standby Mode Display ( In the standby mode, it is possible to set the display to show; Base Number ), Handset Number ( •...
31939_KX-TCD700CX_Czech 18/6/01 Setting Call Option Within the Call Option menu, it is possible to program the following: • Set Call Prohibition ( • Set Direct Call Number ( memory. This feature allows you to make a call easily by pressing Incoming calls are accepted.
31939_KX-TCD700CX_Czech 18/6/01 • Set Call Prohibition (this prohibits anyone from making a call with your handset including emergency numbers. Incoming calls are accepted ( • Set Direct Call ON/OFF ( (Standby Mode) Note: • To return to the previous step during programming, •...
31939_KX-TCD700CX_Czech 18/6/01 Setting Other Options Within the Other Option menu, you can program the following: • Change Handset PIN ( • Set Auto Talk ON/OFF ( The Auto Talk feature allows you to answer a call by lifting the handset off the base unit without pressing ON.
(Standby Mode) NOTE: Once you have programmed the password, you cannot confirm it. We recommend you write down the password. If you forget it, please consult your nearest Panasonic Service Centre. 1:54 pm Page 35 • Enter current PIN ).
31939_KX-TCD700CX_Czech 18/6/01 Registration • Registering a Handset to a Base Unit ( The handset supplied with the base unit is already registered. If an optional handset/base unit is purchased, the following procedure needs to be carried out before initial use. and Hold on base unit for 10 secs.
31939_KX-TCD700CX_Czech 18/6/01 • Cancelling a Base Unit ( If another handset is out of range and/or its power is OFF when ‘Cancelling a Handset’, the previous base unit number will still remain in the cancelled handset. Therefore, you need to cancel the base unit registered in the cancelled handset.
31939_KX-TCD700CX_Czech 18/6/01 Select Base Unit ( • Automatic Base Unit Access ( The handset automatically selects a registered base unit. • When the handset moves to another base unit radio area, it loses contact with the previous base unit and automatically accesses the new base unit. •...
31939_KX-TCD700CX_Czech 18/6/01 Reset Handset ( This function enables the handset to clear the following settings at one time. They will return to their initial settings. (Standby Mode) Note: • To return to the previous step during programming, • To exit the programming mode at any time, 1:54 pm Page 39 •...
31939_KX-TCD700CX_Czech 18/6/01 Programmable Functions (On the Base Unit) Bell Selection There are three choices for Bell Selection when a call is being received • all handsets ring. “All handsets” • the selected handset(s) ring(s). “Selected handset(s)” • the selected handset rings first. Then if it does not answer, all other handsets will ring, “Selected then all handsets”.
31939_KX-TCD700CX_Czech 18/6/01 To Select the Base Unit Ringer Volume 4 levels are available. The factory pre-set is MEDIUM. When set to OFF, the base unit will not ring. To Select the Dialling Mode You can program the dialling mode to tone or pulse. If you have touch tone service, set to tone.
Select Earth/Flash Mode The earth relay can be installed as an option depending on your PBX requirements. Please consult your nearest Panasonic Service Centre for installation. Then you can select the flash or earth mode. The factory pre-set is Flash.
NOTE: Once you have programmed the password, you cannot confirm it. We recommend you write down the password. If you forget it, please consult your nearest Panasonic Service Centre. 1:54 pm Page 43 ➡ • To Cancel a Handset.
31939_KX-TCD700CX_Czech 18/6/01 Reset Base Unit This function enables the base unit to clear the following settings at one time. They will return to their initial settings. The following are factory default settings of the Base Unit. Function Bell Selection Dialling Mode Earth/Flash Flash Timing Pause Timing...
31939_KX-TCD700CX_Czech 18/6/01 Option Covers You can change the look of your phone’s handset with Option Covers. 1. Remove the battery cover by sliding while pressing the arrow. Remove the batteries. 2. The option cover is locked with the right and left tabs. Unlock one of the tabs by pressing horizontally ➀...
31939_KX-TCD700CX_Czech 18/6/01 4. Place the new option cover fitting the tabs on the cover into their slots on the handset. 5. Snap the option cover shut on the lower ➀, middle ➁ and upper ➂ parts of the handset. 6. Connect the batteries and close the battery cover. Using the Belt Clip You can hang the handset on your belt or pocket using the belt clip.
31939_KX-TCD700CX_Czech 18/6/01 Before Requesting Help Problem The unit does not work. “ ” flashes and an alarm tone sounds when you A busy tone sounds when you You cannot dial. “ ” flashes during a conversation and the call is disconnected. Static, sound cuts in/out, fades.
Page 48
31939_KX-TCD700CX_Czech 18/6/01 Problem While programming or searching, the unit starts to ring and stops the program/search. The unit does not display the caller’s phone numbers. does not function. You cannot redial. The paged handset does not answer. While using the intercom, two tones sound.
28426_English 13/2/01 3:58 pm ➡ Before Requesting Help Problem “ ” flashes or the unit bleeps every 15 seconds. You charged the batteries fully, You charged the batteries fully, but “ ” flashes. but “ ” flashes. Adding Another Phone This unit will not function during a power failure.