Attwood 7200 Series Installation Instructions

3
Anchor/Masthead Light
12-Volt: 7200 and 7400 Series
24-Volt: 7250 and 7450 Series
Installation Instructions
SAVE THESE INSTRUCTIONS
Form Number 69394 Rev. B
FEATURES
Attwood 3-mile (4.8 km) Anchor/Masthead Lights consist of anodized
aluminum poles with lightweight heads. Horizontal and vertical bases
allow light pole to be adjusted and locked within a 180 arc.
Lights provide a 3-mile, 225 forward running light and 2-mile all-round
anchor light. For power-driven boats boats up to 65.6 feet (20 meters).
Lights meet USCG CFR 183.810, ABYC A-16 requirements, and all
applicable standards as tested by Imanna Laboratory, Inc., December
17, 2003. Lights use 8-watt festoon lamp, #9230 (for 12-volt systems)
or #910409 (for 24-volt systems).
CAUTION
To prevent personal injury, disconnect the power source when installing
or servicing any electrical product. Remove vessel from water when
using any 120 VAC power tools.
Lens can be HOT and can melt or scorch fabric. When folded down,
turn light OFF and be sure lens does not touch anything.
REQUIRED FOR INSTALLATION
• Cordless drill; 1/8" and 3/8" (3 and 10mm) bits
• Marine-grade non-silicone sealant
• Phillips screwdriver
• Two #10 pan head stainless steel screws
• 3-position switch (OFF/ON/ON)
• Fuse holder and fuse: 2-amp (for 12-volt systems) or 1-amp
(for 24-volt systems)
• 16-gauge wire
• Marine-grade wire connectors for 16-gauge wire
MOUNTING LOCATION
CAUTION
Install light so that fin (Figure 3) is TOWARD STERN and aligned on
the fore/aft centerline of the vessel (within 1 ). If not properly aligned,
lights will not shine in required fore/aft arc.
Base must pivot on the fore/aft centerline and be mounted on a surface
that allows a 360 arc of unobstructed light visibility. (Figure 1)
Bases are available for mounting on vertical or horizontal surfaces.
Release the cam-lock adjustment handle to fold light or adjust to
vertical position.
Figure 1
INSTALLATION INSTRUCTIONS
Change Base Type (If Required)
Packaged versions of the Anchor/Masthead Light are shipped with
the vertical base installed. To switch to the horizontal base:
1. Carefully remove the cam-lock screw and oblong washer. Set aside
for reinstallation (Figure 2).
2. Pivot the base axle out of its socket. Note position of the 3 wires in
the base slot. Remove the vertical base.
3. Insert wires through slot of the horizontal base. Install in reverse order.
®
For windshield, on horizontal
Figure 2
STEP 1
Cam-lock Screw
and Oblong Washer
04-07
Install Light
1. Release cam-lock adjustment handle and adjust light to vertical
position. (Figure 3)
2. Place light in selected position. BE SURE THAT FIN IS ALIGNED
TOWARD STERN.
3. Use provided adaptors, if necessary, to allow installation on
angled windshields.
Figure 3
FWD
FWD
4. Using the base as a template, mark the two mounting hole
locations and one wire access hole. (Figure 4)
CAUTION
Position wire access hole carefully, especially on aluminum boats,
so that wires do not contact the hull.
5. Remove light. Drill two 1/8" (3mm) pilot holes for #10 screws. Drill
one 3/8" (10mm) wire access hole.
6. Bring two 16-gauge (+) wires and one 16-gauge (-) wire up through
access hole. DO NOT connect power to switch until you read
CONNECT POWER TO SWITCH.
7. Use marine-grade waterproof crimp connectors to connect blue
wire to one (+) positive lead from 3-position switch; connect gray
wire to second (+) lead. Connect (-) negative source to black wire
and route to (-) negative terminal on battery.
8. Fasten light to deck with two #10 stainless steel pan head screws.
DO NOT OVERTIGHTEN.
STEP 2 STEP 3
Vertical Horizontal
Base Base
Feed Wires Thru
Fin
(AFT)
Locked
Unlocked
Vertical Mount
AFT PORT
Fin
(AFT)
Locked
Unlocked
Horizontal Mount
AFT PORT
Socket
Axle
STBD
STBD