Olympus FL-50 Instruction page 7

<TTL AUTO>
In this mode, pre-flash is performed to measure the optimum flash intensity and then actual flash
is performed.
1.
Displayed according to the
focal length of the lens.
2.
3.
Light control range
■Light intensity adjustment
The flash light intensity can be adjusted between +3 and –3.
1.
2.
3.
Light intensity adjustment value
46
The control panel shows the light control range according
to the camera setup.
Confirm that the distance to the subject is within the light
control range.
If not, adjust the lens iris (F) or the subject distance.
The light control range varies according to the camera type
and camera setup (ISO speed, lens iris (F) and lens focal
distance (ZOOM)).
When flash activation has been performed correctly, the
AUTO CHECK lamp blinks for about 5 seconds after the
shutter is released.
The light intensity adjustment must be set to ON in the
custom setup operation (page 61).
• The indicator appears in the control panel.
Turn dial B to select a light intensity adjustment value in
the following steps.
(This selection is also possible with dial A.)
0 → +0.3 → +0.7→ +1.0 ... +3.0
0 → –0.3 → –0.7→ –1.0 ... –3.0
The display shows the light intensity adjustment value ex-
cept when the value is 0, in which case the display does
not show the light control range.
If the camera's flash adjustment mode is selected, the
actual flash light intensity will be the total of the light
intensity adjustment value set on the FL-50 and that
set on the camera. The light intensity adjustment value
displayed is that of the FL-50 only.
[Example]
Selected Adjustment value Actual light intensity
adjustment value displayed on FL-50 adjustment
FL-50 +0.3
+0.3
Camera +0.3
<AUTO>
In this mode, the flash light intensity is controlled automatically according to the lens iris (F)
setting and the amount of light input to the auto light receptor.
Displayed according to the
focal distance of the lens.
Light control range
+0.6
1.
The control panel shows the light control range according
to the camera setup.
The light control range is not displayed if the camera setup
(ISO speed and lens iris (F)) does match one of the us-
able ISO speed/lens iris (F) combinations.
In this case, the ISO and F indicators blink to alert you.
Change the camera setup (ISO speed and/or lens iris (F)).
2.
Confirm that the distance to the subject is within the light
control range.
If not, adjust the lens iris (F) or the subject distance.
The light control range varies according to the camera setup
(ISO speed, lens iris (F) and lens focal length (ZOOM)).
■Combinations of ISO speeds and lens irises
controllable in AUTO mode
ISO speed
3200 1600 800 400 200 100
F8 F5.6 F4 F2.8 F2 F1.4
F11 F8 F5.6 F4 F2.8 F2
F16 F11 F8 F5.6 F4 F2.8
F22 F16 F11 F8 F5.6 F4
F32 F22 F16 F11 F8 F5.6
F32 F22 F16 F11 F8
F32 F22 F16 F11
F32 F22 F16
F32 F22
3.
When flash activation has been performed correctly, the
AUTO CHECK lamp blinks for about 5 seconds after the
shutter is released.
Memo:
Test flash activation
Flash activation can be tested before actually releasing
the shutter.
Press the Test button for test flash activation.
The light control is OK when the AUTO CHECK lamp blinks
for about 5 seconds after the test flash activation.
If the lamp does not blink, change the lens iris (F), ISO
speed, subject distance, etc.
• The light check by means of test flash activation is pos-
sible only in the AUTO mode.
50 25
F1.4
F2 F1.4
F2.8 F2
F4 F2.8
F5.6 F4
F8 F5.6
F11 F8
F16 F11
47