Personal Protective Equipment; Protection Against Electric Shock; Safe Working Practices - Makita UC3520A Instruction Manual

4. Working with the chain saw requires a high level
of concentration. Do not work with the saw if you
are not feeling fit and well. Carry out all work
calmly and carefully.
5. Never work under the influence of alcohol, drugs
or medication.
Proper use
1. The chain saw is intended solely for cutting wood.
Do not use it for example to cut plastic or porous
concrete.
2. Only use the chain saw for operations described
in this instruction manual. Do not, for example,
use it to trim hedges or for similar purposes.
3. The chain saw must not be used for forestry work,
i.e. for felling and limbing standing timber. The
chain saw cable does not provide the operator
with the mobility and safety required for such
work.
4. The chain saw is not intended for commercial use.
5. Do not overload the chain saw.

Personal protective equipment

1. Clothing must be close-fitting, but must not
obstruct mobility.
2. Wear the following protective clothing during
work:
A tested safety helmet, if a hazard is
•
presented by falling branches or similar;
A face mask or goggles;
•
Suitable ear protection (ear muffs, custom or
•
mouldable ear plugs). Octave brand analysis
upon request.
Firm leather safety gloves;
•
Long trousers manufactured from strong
•
fabric;
Protective dungarees of cut-resistant fabric;
•
Safety shoes or boots with non-slip soles,
•
steel toes, and cut-resistant fabric lining;
A breathing mask, when carrying out work
•
which produces dust (e.g. sawing dry wood).

Protection against electric shock

･
The chain saw must not be used in wet
weather or damp environments, as the
electric motor is not waterproof.
1. Only plug the saw into earthed sockets in tested
electrical circuits. Check that the system voltage
matches that on the rating plate. Ensure that a 16
A line fuse is fitted. Saws used in the open air
must be connected to a residual current-operated
circuit-breaker with an operating current no higher
than 30 mA.
･
Should
damaged, withdraw the mains plug
immediately.
the connecting cable

Safe working practices

1. Before starting work, check that the chain saw is
in proper working order and that its condition
complies with the safety regulations. Check in
particular that:
The chain brake is working properly;
•
The run-down brake is working properly;
•
The bar and the sprocket cover are fitted
•
correctly;
The chain has been sharpened and tensioned
•
in accordance with the regulations;
The mains cable and mains plug are
•
undamaged;
Refer to the "CHECKS " section.
2. Always ensure in particular that the extension
cable used is of adequate cross-section (see
"SPECIFICATIONS"). When using a cable reel,
wind the cable completely off the reel. When using
the saw in the open air, ensure that the cable
employed is intended for open-air use and is rated
accordingly.
3. Keep the cord away from the cutting area and to
position cord so that it will not be caught on
branches, and the like, during cutting.
4. Do not operate the chain saw in the vicinity of
flammable dust or gases, as the motor generates
sparks and presents a risk of explosion.
5. Work only on firm ground and with a good footing.
Pay particular attention to obstacles (e.g. the
cable) in the working area. Take particular care
where moisture, ice, snow, freshly cut wood or
bark may make surfaces slippery. Do not stand on
ladders or trees when using the saw.
6. Take particular care when working on sloping
ground; rolling trunks and branches pose a
potential hazard.
7. Never cut above shoulder height.
8. Hold the chain saw with both hands when
switching it on and using it. Hold the rear
handle with your right hand and the front handle
with your left. Hold the handles firmly with your
thumbs. The bar and the chain must not be in
contact with any objects when the saw is switched
on.
be
006908
8