New Buck Corporation 80ZC User Manual
Buck stoves cooktop user manual
Hide thumbs
Also See for 80ZC:
- Operation maintenance safety (29 pages) ,
- Installation instructions manual (28 pages)
Related Manuals for New Buck Corporation 80ZC
Summary of Contents for New Buck Corporation 80ZC
- Page 1 The following manual is for the 80ZC cabinet ONLY. If you require information on the Model 80 unit that fits inside this cabinet, please download the Model 80 manual from the “Stove Manuals” section of our website. Thank you for...
- Page 2 MODEL 80 ZC CABINET INSTALLATION FEATURES: INSTALLATION: MAINTENANCE: PREPARATION: OPERATION: SAFETY: NEW BUCK CORPORATION 1992 NARNOCK HERSEY...
-
Page 3: Side Panel
IMPORTANT The Top Panel _On Cabinet Before Setting The Cabinet For Framing. TeP PANEL KfiA'l" IKIM LOUVl:RS FRONT l.J.. FRONT,VIEW (#1 ) Side-Panels (#2) tf.\ FRONT ~'xx >tx >\ ~it1- l.J.. Must Be Installed TOP PANEL - INSllATION CAP INSLlAT ION LAYERS FRONT SIDE PANEL SIDE VIEW... - Page 4 CAUTION - Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts. Be sure to follow chimney instructions for proper clearances to combusti- bles and proper air spacing required. -',- Chlmnoy Cap CAUTION: Vented Root Flashings are required with certain chimney installa· tions.
- Page 5 CAUTION: Do not mix Ch imney P arts as a fire. may re su 1 t. model of listed chimney parts completely for·an CAUTION: Read through all of these instructions carefully. Follow Chimney Manufacturer's Installation exactly. install the Cabinet, Stove, and Chimney as described in the instructions will void the manufacturer's warranty.
-
Page 6: Installation Precautions
INSTALLATION PRECAUTIONS The following precautions are mandatory for a safe installation: Compliance with local building codes and regulations is mandatory. Be careful not to damage unit in handling and unpacking component parts and accessories. Use only listed approved chimney pipes. The chimney must extend a minimum of three feet above the hig'hest point where it penetrates the roof (three feet above a flat roof or up to a... - Page 7 A. Straight up through ceiling: simple installation normally used when installing a Hodel ZC-80 inside an existing room, and in iome cases, in new construction. Refer to Figure 3 if an offset to clear an obstruction is needed. CAUTION- Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts.
- Page 8 FRAMING CONSTRUCTION Except as noted, the Hodel ZC-80 can be installed almost anywhere you desire. There are, however, a few clearance and framing restrictions that must be followed. sure that these clearance restrictions are met. to place your Hodel ZC-80 correctly at the start of the installa- tion than to be forced to relocate it after much of the work is done.
- Page 9 Framing must be accomplished after the Model ZC-80 is set in place. The chimney can be installed after framing, but installa- tion is considerably more difficult and, in some cases, ble. Therefore, it is recommended that the chimney be installed prior to framing when a choice exists.
- Page 10 Set Hodel ZC-80 unit in place and attach safety shield to unit as shown in Figure i-A and i-B. You must place a noncom- bustible material 3/4" thick millboard or equivalent K Factor =.084/BTU/F 2 H0F inches minimum. 3. Frame the ZC Cabinet usng 2"x 4" studs or local building code framing.
- Page 11 Chimney Cap //?~-- Chimney Pipe "Y~ FIGURE 7 EXTERIOR ROOF OR CHASE CAUTION! Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts. follow chimney instructions for proper clearances to combusti- bles and proper air spacing required. 4-'::;"':~-- 2"...
- Page 12 f f i - - - Chimney Cap 0--\.--1- Storm Collar ---:f-- Roof Flashing Chimney Pipe -"'C-~7"''-?.-s-'S1'f--i-H-tt+f-- FIGURE 8 CORNER LOCATION FRAMING CAUTION! Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts. follow chimney instructions for proper clearances to combusti- bles and proper air spacing required.
- Page 13 Install pipe to cabinet by pushing ~tarter down over the on the ZC Cabinet. NOTE: To ease installation of the first section of pipe to the Cabinet use a pipe crimping tool and crimp the bottom of the inside chimney liner. Maintain a 2 inch minimum clearance section of pipe...
- Page 14 INSTALLING FIRESTOP RADIATION SHIELD: tion Shield to' the bottom of the framed ceiling opening using at least two 8-penny nails per side. CHIMNEY INSTALLATION INFORMATION ROOF CLEARANCE Frame a square opening in roof maintaining the required 2" clearance to combustible materials between the chimney and the framed opening and roofing material.
- Page 15 Electrical procedures: electrician must wire the Cabinet into the home wiring. system using No. 14 AWG (with ground wiring) as minimum in accordance with local wiring codes. Remove receptacle cover. Remove receptacle from mounting box. Run No. 14 AWG wire directly from house wiring in through the Field Connector in the lower right side of the Cabi- Leave 4-6 inches of wire extending out of the box.
- Page 16 FINISHING Finishing can now be completed using the desired material in accordance with local building and fire codes. CAUTION: Do not cover any opening on the Cabinet; heat must be allowed to escape from the openings designed into the unit. grilled trim panel is provided with the trim package to cover this area.
- Page 17 INSTALLING THE MODEL 80 BUCK STOVE Install unit as follows: Carefully reinspect chimney connections, vent outputs and cabinet air intakes after finishing is completed. Thoroughly clean all masonry mud and debris from cabinet and surrounding environment. Ensure that Cabinet has not been damaged during masonry pro- cess.
- Page 18 Install the trim kit attaching it to the Cabinet or finished framing by using 1" screws to secure the trim panels in place. Remove cover plate from Cabinet exposing receptacle. Roll up pOHer cord so it will fit inside of cover box. Plug in pOHer cord in receptacle.