NAPCO Magnum Alert 800 Operating Manual
  1. Manuals
  2. Brands
  3. NAPCO Manuals
  4. Security System
  5. Magnum Alert 800
  6. Operating manual
NAPCO Magnum Alert 800 Operating Manual

NAPCO Magnum Alert 800 Operating Manual

Napco security system operating guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

OPERATING
GUIDE
FOR YOUR
MAGNUM
SECURITY

Advertisement

Table of Contents
loading

Related Manuals for NAPCO Magnum Alert 800

Summary of Contents for NAPCO Magnum Alert 800

  • Page 1 OPERATING GUIDE FOR YOUR MAGNUM ALEm-800/800s SECURITY SYmM 01955 NAPCO...
  • Page 2 You have taken a major step in protecting your home or busi- ness by having a Napco Magnum Alert-800/800S Alarm Control Center installed. Please read this guide thor- oughly to familiarize yourself with your new security system. Keep this booklet handy for future reference.
  • Page 3 A delay period that allows the system to be reset before it reports to a cantml station. AlmmPlmn our premises pro- Identifies the areas of protection and lists tected by each zone or zone features (see page 15). Anrrkrg/- Turning yours tern ON or OFF. This can r”.
  • Page 4 lndlcator ughts -/-n=Y Steady - system is armed. Flashes - system is in alarm. Count the number of flashes to tell in which zone the alarm occurred. Example: Fourflashes- alarm in Zone 4. smU9Mf-l Steady - system is disarmed, all zones okay.
  • Page 5 Each security system is custom tailored to the owner’s needs, but all MAGNUM ALERTBOO/ 800s have the following: zones Your system contains up to six separate zones. Each zone is an independent circuit that pro- tects specific areas of your home. For example: your afarm spe- cialist may have set aside a zone for window protection, exit/entry...
  • Page 6 If your system includes the Napco Digit-Key keypad you can choose your own private code to arm and disarm the Control Center. To program your code, slide the switch (upper left hand corner of your Control Center) into the LOAD position. Go to the Digit-Key keypad and enter any combination of numbers up to 6 digits (there is no zero).
  • Page 7 First, check the green STATUS light at the keypad or keyswitch. If this light is on stead- ily, enter your code. The red ARMED/MEMORY light will come on and the green lamp will go out. Leave immediately through the entry/exit doorway before the delay time runs out.
  • Page 8 SHUNT button, labeled “S”, and enter your code. The yellow SHUNT light and the red ARMED/ MEMORY light will come on. The green light will be out. All zones programmed by your alarm spe- cialist to respond to manual shunting will be shunted (even if some are not in “trouble”).
  • Page 9 Arming with zone shunting You might have chosen one or two zones that you can man- ually “shunt out” of the system from the keypad. A shunted (bypassed) zone cannot cause an alarm. Zone shunting may be used for turning off interior protection, or allowing you to turn on only your perimeter protection.

  • Page 10: Panic Alarm

    Panic alarm To activate a panic alarm and call for outside help, press the two buttons marked and # on the Digit-Key keypad. Makesure you press both buttons at the s8me time. The panic zone is capable of sending asilent signal to the Central Station when a Digital Communicator is being used (optional).
  • Page 11 Your Alarm Specialist may have programmed your security system to be monitored by a Central Station. The built-in digital communicator can trans- mit emergency signals to the Centml Station 24 hours a day.
  • Page 12 AbortDeby Note which zones on your alarm plan have abort delay. This is a 16 second delay that enables you to reset the system before a zone condition report is sent to the Central Station. Non-24 hour zones, however, must first be repaired.
  • Page 13 The following information is applicable only where local ordinance permits use of your alarm Control Center for fire detection Controrlklg Your Circuit If your alarm specialist installed smoke detectors or heat sensing thermostats, you have 24 hour fire protection. This optional Fire Pro- tection Zone is always active, even though your system may be dis- armed.
  • Page 14 an escape plan Even with the most advanced fire alarm system, adequate pro- tection requires an escape plan. To prepare your plan: Draw floorplans of your build- ing (see sample). Show two exits: a front or back door and a window from each room. (Make sure the window works.
  • Page 15 Zone Area Protected Aux. Central Station? Service Person ‘optlonal katun, Contacts Zone Features (doors, windows, etc.) Telephone# Telephone#...
  • Page 16 NAPCOLlMiTEDWARRANly...

This manual is also suitable for:

Magnum alert 800s

Table of Contents