Table of Contents
Advertisement
Installation Guide
Color CCTV Camera
WV-CW634S
Model No.
WV-CW634F
WV-CW634S
WV-CW634F
For information about how to perform the settings and how to operate the
camera, refer to the Operating Instructions on the provided CD-ROM.
Before attempting to connect or operate this product, please read these
instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
Advertisement
Table of Contents
Related Manuals for Panasonic WV-CW634S
Summary of Contents for Panasonic WV-CW634S
-
Page 1: Installation Guide
Installation Guide Color CCTV Camera WV-CW634S Model No. WV-CW634F WV-CW634S WV-CW634F For information about how to perform the settings and how to operate the camera, refer to the Operating Instructions on the provided CD-ROM. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. - Page 2 WARNING: CAUTION: • This apparatus must be earthed. • An ALL-POLE MAINS SWITCH with a contact • Apparatus shall be connected to a mains separation of at least 3 mm in each pole shall socket outlet with a protective earthing con- be incorporated in the electrical installation of nection.
-
Page 3: Important Safety Instructions
Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not block any ventilation openings. Install in accordance with the manufacturer's instruc- tions. 6) Do not install near any heat sources such as radiators, heat registers, stoves, or other appara- tus (including amplifiers) that produce heat. 7) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. -
Page 4: Limitation Of Liability
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVE- MENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S). Disclaimer of warranty IN NO EVENT SHALL Panasonic System Networks Co., Ltd. BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW: (1) ANY LOSS OR DAMAGE, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPE- CIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PROD- UCT;... -
Page 5: Table Of Contents
Contents Important safety instructions ......................3 Limitation of liability ........................4 Disclaimer of warranty ........................4 Preface ............................6 Features ............................6 About the user manuals ........................ 7 Trademarks and registered trademarks..................7 Precautions ........................... 8 Precautions for Installation ......................10 Major operating controls and their functions ................ -
Page 6: Preface
Preface This product is a 1/3-inch type {1/3"} CCD color CCTV camera. Connection of this product to a video monitor allows users to use this product as a monitoring camera. Features Super Dynamic 6 For photographic subjects which contain high contrast between the bright and dark areas, light compensation on the pixel level will result in more natural-looking images. Introduction of newly developed high-resolution CCD The introduction of the newly developed CCD with 976 of horizontal pixels has led to the horizontal resolution of as high as 700 TV lines (typ.). Auto back focus (ABF) function equipped Moving the CCD inside the camera to an optimal position with the operation button of this unit or the setup menu allows users to automatically adjust the back focus. -
Page 7: About The User Manuals
Note: • The VMD function is not the dedicated function to prevent thefts, fires, etc. We are not respon- sible for any accidents or damages caused by applying the function for the above purposes. Optional heater unit can be connected When using the optional heater unit, the product can be used at temperatures within –30 °C to +60 °C {–22 °F to +140 °F} and humidity within 10 % to 90 %. The camera conforms to the IP66 and provides high dust resistance and waterproof performance. -
Page 8: Precautions
Precautions The following points as well as the con- This product shall be installed in a vibra- tents of "Warning" and "Caution" shall be tion-free place. observed. Failure to observe this may cause screws and bolts to be loosened and consequently to fall Refer installation work to the dealer. -
Page 9: Precautions For Use
[Precautions for use] Cleaning this product body Turn the power off when cleaning the product. This product has no power switch. Do not use strong abrasive detergent when Turn the power off when cleaning the product. cleaning this product. Otherwise, it may cause discoloration. When using a chemical cloth for To keep on using with stable performance cleaning, read the caution provided with the Parts of this product may deteriorate and it chemical cloth product. -
Page 10: Precautions For Installation
Precautions for Installation The following points as well as the contents of "Warning" and "Caution" shall be observed. Panasonic assumes no responsibility for • Locations where the temperature is not with- injuries or property damage resulting from in –10 °C to +60 °C {+14 °F to +140 °F}. failures arising out of improper installation (When using the optional heater unit, the... - Page 11 Mounting screws • The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area. • Do not use an impact driver. Failure to observe this may cause overtightening and consequently damage to the screws. • When a screw is tightened, make the screw at a right angle to the surface. After tightening the screws or bolts, perform visual check to ensure tightening is enough...
-
Page 12: Major Operating Controls And Their Functions
Major operating controls and their functions w Video output cable q Power cord !9 Inner dome e Enclosure @0 Dome * This illustration shows the camera without the inner dome. r Panning table u Panning lock screw t Tilt adjusting table y Tilting lock screw i Focus lock knob o Zoom lock knob... - Page 13 q Power cord !5 Down button [(DOWN), ABF1] Moves the cursor downward and selects w Video output cable items in the setup menu. Refer to page 29 for further information about [ABF1]. e Enclosure (Pressing and holding for 3 s, image upside- down) r Panning table Rotate this table to adjust the panning !6 Setting button [(SET), ABF2/MENU] angle of the camera. Confirms the setting contents. Refer to page 31 for further information about [ABF2].
-
Page 14: Preparations
Preparations When installing the camera on a wall or a ceiling, there are two methods as specified below. (+ Next page) • Using a two-gang junction box (locally procured) • WV-CW634S: Using the mounting base (accessory) WV-CW634F: Using the mounting base WV-Q115A (option) Refer to all work related to the installation of this product to qualified service personnel or system installer. • The mounting base WV-Q115A is optional for WV-CW634F. Use the screws supplied with the camera mount bracket. Important: • Prepare the mounting screw according to the material of the area where the attachment plate (accessory) is to be installed. In this case, wood screws and nails should not be used. For mounting a camera on a concrete ceiling, use an anchor bolt (M4) or an AY plug bolt (M4) for securing. - Page 15 Installation shall be performed in such a manner that " TOP" of the attachment plate faces upward. • For ceiling mounting: The front side (model number indication face) of the camera shall be aligned in the direction of the arrow in " FRONT" on the attachment plate. WV-CW634S: Using the mounting base (accessory) WV-CW634F: Using the mounting base WV-Q115A (option) • When installing the camera with the mounting base WV-Q115A, attach the mounting base to the wall or ceiling in the first place. (+ next page.) Mount the attachment plate (accessory) by using the screws supplied with mount bracket. (+ next page.) (Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
- Page 16 Install the mount bracket (mounting base) on the wall/ceiling. ø27 mm {1-1/16"} Cable access hole (A For use of the hole) 51 mm {2"} WV-Q115A Center of mounting base Female thread for conduit Cap for the female thread for the conduit (For use of the hole A) (For use of the hole B) 85 mm {3-11/32"}...
- Page 17 Previously run the cables from the wall or ceiling through the cable access hole. Mount the attachment plate onto the mount bracket (mounting base). Recommended tightening torque: 0.78 N·m {0.58 lbf·ft} Attachment plate Note: • For wall mounting: Installation shall be performed in such a manner that " TOP" of the attachment plate faces upward. (Except for the case of connecting the conduit from the top. (+ page 18)) • For ceiling mounting: The front side (model number indication face) of the camera shall be aligned in the direction of...
- Page 18 Important: • If open wiring is conducted, be sure to use conduits and run the cables inside the tubes to pro- tect the cables from direct sunlight. • When the conduit is connected at the lateral or bottom position, either of the arrow marks on the bracket shall be the top position. • When the conduit is connected from the top, the arrow mark on the attachment shall be either of the right or left position. <To connect conduit from the side or bottom> Arrow mark Connecting conduit <To connect conduit from the top> Female thread for conduit • Installation work shall be such that there is no intrusion of water into the architecture through the conduits having been joined.
-
Page 19: Make A Connection
Make a connection Cautions: • ONLY CONNECT WV-CW634S/WV-CW634F TO 24 V AC OR 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1). • Be sure to connect the grounding lead to the GND terminal. Brown (Live) To 24 V AC/12 V DC* power supply Blue (Neutral) Power cord Green/Yellow (GND) To GND (only for 24 V AC) (approx. 17 cm * When using 12 V DC power supply, {55.8 ft}) - Page 20 • Cord length and wire gauge 24 V AC The recommended cord length and copper wire size are shown in the table for reference. The voltage supplied to the camera should be between 19.5 V AC and 28 V AC. Recommended wire gauge for 24 V AC line. Copper wire #24 #22 #20 #18 size (AWG) (0.22 mm (0.33 mm (0.52 mm (0.83 mm Length of c a b l e (approx.) 12 V DC The recommended resisance and copper wire size are shown in the table for reference.
- Page 21 Waterproof treatment for the cable joint sections Adequate waterproof treatment is required for the cables when the camera with exposed cables is installed by means of the mounting base WV-Q115A or it is installed under the eaves. The camera body is waterproof, but the cable ends are not waterproof. Be sure to use the supplied waterproof tape at the connection parts of the power cord and video output cable to apply waterproof treatment in the following procedure. Failure to observe this may cause water leakage resulting in malfunction. When using power cord When using video output cable <How to wind the supplied waterproof tape> Stretch the tape by approx. twice (see the illustration below) and wind it around the cable. Insuffi- cient tape stretch causes insufficient waterproofing. Stretch the tape to about twice. Double length Note: • To install this product outdoors, be sure to waterproof the cables. The camera body is water- proof (IEC IP66 or equivalent) only when installation specified in this document and appropriate waterproofing are properly performed. The bracket is not waterproof.
-
Page 22: How To Install The Heater Unit
Optional Heater Unit WV-CW5HA (option) Installing the heater unit enables the camera to operate in a low-temperature environment below –30 °C {–22 °F}. The heater turns on automatically when the temperature inside the camera drops below +10 °C {50 °F} and turns off when the temperature rises. A small fan inside the unit will mini- mize condensation on the surface of the enclosure caused by changes in ambient temperature unless temperatures change too rapidly. Important: • When using 12 V DC power supply, the optional heater unit is unavailable. • Turning the heater on and off may disturb the camera images. • The power supply of the camera shall be turned off when mounting or dismounting the heater. -
Page 23: Camera Installation
Camera installation Mount the camera. <To mount the camera on a two-gang junction box> q Connect the power cord and the video output cable. (+ page 19) w Align the "OPEN" mark of the camera with the protrusion of the attachment plate. e Engage the attachment mounting screw of the camera with the camera mounting hole of the attachment plate and rotate the camera in the direction of the arrow to the "LOCK" position to secure the camera to the attachment plate without any backlash. Protrusion Camera mounting hole Attachment mounting screw... - Page 24 <To use the mounting base> q Attach the camera onto the attachment plate while aligning the "OPEN" mark of the camera with the projection of the attachment plate. Projection Important: • When mounting the camera body, cables shall be run between the attachment plate and mounting base as indicated by the arrow in the illustration.
- Page 25 w Engage the attachment mounting screw of the camera with the camera mounting hole of the attachment plate and rotate the camera in the direction of the arrow to the "LOCK" position to secure the camera to the attachment plate without any backlash. Projections e Connect the power cord and the video output cable at the side of the mounting base. (+ page 19) Apply waterproof treatment to the con- nected section. (+ page 21) Make cable connections.
- Page 26 t Mount the supplied base cover on the mounting base. Important: • To prevent the cables from being caught when the base cover is attached, keep the cables inside the cable guide. Base cover y Use the bit for tamperproof screw (acces- sory) to tighten the fixing screws provided Base cover fixing screw on both sides of the base cover. (Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
- Page 27 Remove the enclosure and inner dome from the main body by loos- ening the three fixing screws. Loosen the three fixing screws by using the provided bit for tamperproof screw. Detach the inner dome while pushing the parts with the "PUSH" indication. Press the parts with the "PUSH" indication. Important: • Do not hold the inner dome when carrying the camera. Otherwise, the camera part...
-
Page 28: Adjust The Camera
Adjust the camera Be sure to view the monitor for adjustment when the camera angle is adjusted. Connect the monitor for adjustment (e.g. a small LCD) to the monitor output connector, and adjust the camera angle. When determining the camera angle, repeat fine follow the adjusting procedure of q, w, and e shown below. Tilt adjusting table Tilting lock screw Monitor output connector (RCA) Panning table... - Page 29 Adjusts the focus. Focus adjustment shall be performed when camera Focus lock knob angle adjustment are performed. Adjust the focus by following the adjusting proce- dure of q, w, and e shown below. NEAR NEAR q Loosen the zoom lock knob and move the Zoom lock knob knob between TELE and WIDE to obtain the WIDE WIDE TELE TELE...
- Page 30 To perform fine adjustment of the back focus after the ABF operation indicator goes off and automatic back focus is adjusted, use the right or left button. Note: • No operation for 10 seconds or more automatically clears the focus position indicator. • To change the angle of view by moving the zoom adjustment ring, also move the focus lock knob to adjust the focus.
- Page 31 Mount the enclosure and inner dome. Tighten the screws that have been loos- ened in Step 2 in page 27 using the supplied Cutout for Groove for mounting mounting driver bit. (Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}) Important: • Attach the inner dome in accordance with the lens direction to not to change the lens direction. • Check if the tabs of the inner dome are firmly fit. • Remove the cushioning (pink sheet) from the inside of the dome and the protection sheet from the outside of the dome.
-
Page 32: Setup Menu
Setup menu Performing each setting item in the setup menu should be completed in advance to use this unit. Perform the settings for each item in accordance with the installation conditions and customer requirements. List of setup menu Setup item Description CAMERA ID This item specifies the camera title. The camera title that indicates the camera location and other information about the camera is created with alphanumeric characters and symbol, and then displayed on the screen. Performs the camera operation settings. CAMERA Selects a scene file. It is possible to register and save the settings as a SCENE 1/ scene file in case that it is necessary to change the settings such when SCENE 2 shooting at night. Selects the method of controlling the quantity of light in accordance with ALC/ELC the lens to be used. Specifies the electronic shutter speed. SHUTTER Specifies gain adjustment. Specifies electronic sensitivity enhancement. -
Page 33: Basic Operation
Basic operation The operations in the setup menu are performed with the operation buttons after calling up the setup menu on the connected video monitor. The description below explains how to operate the setup menu basically. Screenshot 1 Hold down the [SET] button for about 2 seconds Step 1 to call up the top screen of the setup menu. Press the [UP] or [DOWN] button to move the cursor to "END". MODEL WV-CW634 CAMERA ID CAMERA SYSTEM Step 2 BACK-FOCUS SPECIAL LANGUAGE Press the [RIGHT] button to move the cursor to "SETUP", and press the [SET] button to change the setup mode from "DISABLE" to SETUP DISABLE "ENABLE". - Page 34 Screenshot 3 The selected setup screen in the setup menu Step 4 appears on the screen. Perform the settings for each item. Selection of setting item: • **CAMERA SETUP** SCENE1 Press the [UP] button or [DOWN] button to ALC/ELC move the cursor. SHUTTER ON(HIGH) • Change of settings: SENS UP WHITE BAL ATW1 Press the [RIGHT] button or [LEFT] button. HIGH D&R(IR) AUTO1 •...
-
Page 35: Screen Transition Diagram
Screen transition diagram Top screen “CAMERA ID” screen MODEL WV-CW634 **CAMERA ID** CAMERA ID 0123456789 CAMERA ABCDEFGHIJKLM SYSTEM NOPQRSTUVWXYZ BACK-FOCUS ().,'":;&#!?= SPECIAL +- */%$ LANGUAGE SPACE POSI RET TOP END RESET “CAMERA SETUP” screen ....SETUP DISABLE **CAMERA SETUP** SCENE1 ALC/ELC SHUTTER ON(HIGH) -
Page 36: Troubleshooting
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below. Reference Symptom Cause/solution pages • A re the power cord and coaxial cable connected appropriately? → C heck whether the connection is appropriately established. • I s the adjusting monitor connected ? → C heck whether connection is estab- lished. • I s the monitor brightness appropriately No image displayed adjusted, or is the contrast appropriately adjusted? – → C heck whether the monitor settings are appropriate. • W ere the shock absorbers in the dome cover already removed? – → C onfirm whether the shock absorbers have been already removed. -
Page 37: Specifications
10 % to 90 % (no condensation) Waterproof* Main body: IEC60529 (IP66) Shock resistance 50J, IEC60068-2-75 Video output VBS: 1.0 V [p-p]/75 Ω, NTSC, BNC connector ø154 mm × 146 mm (H) ø164 mm × 146 mm (H), {ø6-1/16" × 5-3/4" (H)} 191.5 mm (W) (Base Cover) Dimensions {ø6-7/16" × 5-3/4" (H), 7-9/16" (W)} (Base Cover) Main body: 1.45 kg {3.20 lbs.} Mass (including attachment plate 100 g {0.22 lbs.}) M ount bracket (only for WV-CW634S): 350 g {0.78 lbs.} Main body: Aluminum die cast, light gray Finish Dome cover: Clear polycarbonate resin Others Tamper-resistant enclosure* *1 When using 12 V DC power supply, the optional heater unit is unavailable. *2 With heater unit WV-CW5HA (option) *3 O nly when installation work is properly performed according to the instructions in this manual and appropriate waterproof treatment is performed. *4 C omponent that has a structure on which the screws that are accessible after installation cannot be screwed or unscrewed using an ordinary screwdriver. Camera Image sensor 1/3 inch interline transfer CCD Effective pixels 976 (H) × 494 (V) Scanning area 4.8 mm (H) × 3.6 mm (V) {3/16" × 5/32"}... - Page 38 When using clear dome cover: Color Mode: 0 .08 lx {0.01 footcandle} at F1.4 WIDE 0.0024 lx {0.0003 footcandle} (sensitivity up x32, at F1.4 WIDE)* BW mode: 0 .008 lx {0.001 footcandle} at F1.4 WIDE 0.00024 lx {0.00003 footcandle} (sensitivity up x32, at F1.4 WIDE)* Minimum illumination When using smoke dome cover (option): Color Mode: 0 .16 lx {0.16 footcandle} at F1.4 WIDE 0.0048 lx {0.0048 footcandle} (sensitivity up x32, at F1.4 WIDE)* BW mode: 0 .016 lx {0.016 footcandle} at F1.4 WIDE 0.00048 lx {0.00048 footcandle} (sensitivity up x32, at F1.4 WIDE)* * Converted value Signal-to-noise ratio 52 dB (AGC Off) Dynamic range 52 dB typ. (Super Dynamic 6 ON) Monitor output VBS: 1.0 V [p-p]/75 Ω, NTSC, RCA jack Camera title Up to 16 characters (alphanumeric characters, marks) Light control mode setting ALC/ALC+/ELC Super Dynamic 6 ON/OFF High light compensation (HLC) ON (1)/ON (2)/OFF Fog compensation ON/OFF OFF (1/60 s), 1/100 s, 1/250 s, 1/500 s, 1/1000 s, 1/2000 s, Electronic shutter speed 1/4000 s, 1/10000 s, 1/120000 s...
-
Page 39: Standard Accessories
Lens mount CS-mount Dimensions and Weight indicated are approximate. Specifications are subject to change without notice. Standard accessories CD-ROM* .......................... 1 pc. Installation Guide (this book) .................... 1 pc. Warranty card ........................ 1 pc. *The CD-ROM contains the operating instructions (PDF). The following parts are used during installation procedures. Base cover (for WV-CW634S) .................... 1 pc. Mounting base (for WV-CW634S) .................. 1 pc. Fixing screw for mounting base (for WV-CW634S) .............. 5 pcs. (incl. 1 spare screw) Fixing screw for ceiling mount bracket (for WV-CW634F) ............ 5 pcs. (incl. 1 spare screw) Attachment plate ........................ 1 pc. Bit for tamperproof screw ....................... 1 pc. Waterproof tape ........................ 1 pc. -
Page 40: Optional Accessories
Optional Accessories Dome cover: WV-CW4SA (Smoke type) Heater unit: WV-CW5HA Mounting base: WV-Q115A (only for WV-CW634F) Ceiling mount bracket: WV-Q169A* (Use when installing camera on weak ceiling boards, etc.) Ceiling mount bracket: WV-Q105A* (Use when installing camera on weak ceiling boards, etc.) Ceiling hanging mount bracket: WV-Q121B (Use with the WV-Q124 (suspension mount bracket) to be able to install on a ceiling.) Wall mount bracket: WV-Q122A (Use with the WV-Q124 (suspension mount bracket) to be able to install on a wall.) Mount bracket: WV-Q124 (Use when installing camera using the WV-Q121B or WV-Q122A.) Sun shade: WV-Q7118* * I n order to attach WV-Q169A, WV-Q105A or WV-Q7118 to WV-CW634F, WV-Q115A is required. When using WV-Q169A or WV-Q105A ceiling mount brackets, use them indoors. - Page 44 Panasonic System Communications Company of North America, Unit of Panasonic Corporation of North America www.panasonic.com/business/ For customer support, call 1.800.528.6747 Two Riverfront Plaza, Newark, NJ 07102-5490. Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 www.panasonic.ca © Panasonic System Networks Co., Ltd. 2015...