1. Manuals
  2. Brands
  3. Cub Cadet Manuals
  4. Tractor
  5. 7304
  6. Operator's manual

Cub Cadet 7304 Operator's Manual

7000 series compact tractor
Hide thumbs Also See for 7304:
Table of Contents

Advertisement

Quick Links

Operator's Manual
S
7000
ERIES
COMPACT TRACTOR
MODEL 7304
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning
: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved
forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective
working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the
muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box
361131Cleveland, Ohio 44136-0019.
CUB CADET LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 [www.cubcadet.com]
PRINTED IN U.S.A.
FORM NO. 769-00654
(1/03)

Advertisement

Table of Contents
loading

Related Manuals for Cub Cadet 7304

Summary of Contents for Cub Cadet 7304

  • Page 1 Operator’s Manual 7000 ERIES COMPACT TRACTOR MODEL 7304 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning : This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).

  • Page 2: Table Of Contents

    TABLE OF CONTENTS TO THE OWNER ... 2 CALLING SERVICE INFORMATION ... 2 RECORDING MODEL AND SERIAL NUMBER INFORMATION ... 3 IMPORTANT SAFE OPERATION PRACTICES ... 4 SAFETY LABELS ... 7 SECTION 1: CONTROLS AND FEATURES ... 9 SECTION 2: OPERATION ... 15 SECTION 3: ADJUSTMENTS ...

  • Page 3: Recording Model And Serial Number Information

    RECORDING MODEL AND SERIAL NUMBER INFORMATION Product identification plates are provided for major components of your tractor. The numbers on these plates are important if your tractor should require dealer service, or if you need additional information on your tractor. Prior to using your tractor for the first time, record the numbers from the identification plates in the appropriate spaces provided below.

  • Page 4: Important Safe Operation Practices

    IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR UNIT. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

  • Page 5: Slope Operation

    • Maintain the weight balance of the tractor. Install front end weights to counterbalance heavy implements attached to the three point hitch. Do not operate the tractor with a light front end. • Any towed vehicle with a total weight exceeding that of the tractor should be equipped its own braking system that is operational from the tractor seat.
  • Page 6 • To prevent injury, do not adjust, unclog, clean, or service PTO driven equipment while the tractor engine is running. • Make certain all PTO shields are always installed. 5. SAFETY FRAME (ROPS) Your tractor is equipped with a rollover protective structure (ROPS) which must be maintained in a fully functional condition.

  • Page 7: Safety Labels

    SAFETY LABELS 1. KNOW THE OPERATING AND SAFETY INSTRUCTIONS IN THE OPERATORS'S MANUAL AND ON THE TRACTOR. MOVE THROTTLE TO MID POSITION AND DEPRESS BRAKE PEDAL. TURN KEY TO THE START POSITION. DISENGAGE PTO AND SET PARKING BRAKE. MOVE THROTTLE CONTROL TO MID POSITION AND TURN KEY OFF. •...
  • Page 8 SAFETY LABELS (Cont.) To avoid personal injury, keep PTO shield in place. Pull only from draw bar. pulling from any other point can cause rear overturn. Disengage PTO and stop engine before servicing tractor, or implements, or attaching or detaching implements. FAILURE TO FOLLOW ANY OF THE INSTRUCTIONS ABOVE CAN CAUSE SERIOUS INJURY TO THE OPERATOR, OR OTHER PERSONS.

  • Page 9: Section 1: Controls And Features

    SECTION 1: CONTROLS AND FEATURES FLOORBOARD AND DASH PANEL MOUNTED CONTROLS Steering Wheel PTO Switch Throttle Handle Ignition Switch Brake Pedal Forward/Reverse Pedal * Steering Wheel and Seat Phantomed For Clarity Figure 1 Seat Adjustment Lever Differential Lock Pedal Parking Brake Lever Hazard Light Switch Headlight Switch Instrument Panel...
  • Page 10 NOTE: References to LEFT and RIGHT indicate that side of the tractor when facing forward while seated in the drivers seat. Reference to FRONT indicates the grille end of the tractor; to REAR, the drawbar end. A. Steering Wheel The steering wheel is centered on the dash panel. It is used to change the direction (left or right) of the tractor while driving.
  • Page 11 H. Differential Lock Pedal Diff. Lock Pedal Symbol Figure 6 Located at the rear of the left floor board, the differential lock pedal engages the transmission differential lock. The differential lock is used to gain additional trac- tion when operating the tractor on wet or loose soil. When the pedal is depressed the rear wheels of the tractor are prevented from rotating independently of one another.
  • Page 12 M. Instrument Panel 1. Fuel Gauge The fuel gauge, located on the left side of the instrument panel, monitors the fuel level in the fuel tank. The needle pointing to the right indicates a full tank. The ignition switch must be in the ON position to read the fuel gauge.
  • Page 13 FENDER MOUNTED CONRTOLS AND FEATURES Fuel Fill Cap PTO Reverse Override Switch PTO Selection Lever Hydraulic Lift Lever Trans. Hi/Lo Shift Lever Cup Holder A. Fuel Fill Cap The fuel fill cap is located on the left fender beside the operator’s seat. WARNING: Never fill the fuel tank to the top of the filler neck.
  • Page 14 E. Transmission Hi/Lo Range Shift Lever The Hi/Lo range shift lever is located on the right fender. The lever has two speed range settings and a neutral position. The lever must be shifted into either the high or low range prior to depressing the forward/reverse pedal to drive the tractor.

  • Page 15: Section 2: Operation

    SECTION 2: OPERATION ROLLOVER PROTECTIVE STRUCTURE (ROPS) This tractor is equipped with a foldable Rollover Protection Structure (ROPS) and seat belts. When used together they are effective in reducing injuries to the operator in the event of an accidental tractor rollover.
  • Page 16 SAFETY INTERLOCK SYSTEM This tractor is equipped with a safety interlock system for the protection of the operator. If the interlock system should ever malfunction, do not operate the tractor. Contact your authorized Cub Cadet Dealer. The safety interlock system prevents the engine from cranking or starting unless the brake pedal is fully depressed, and the PTO is “OFF”.
  • Page 17 STARTING THE ENGINE WARNING: Always sit in the operator’s seat when starting the tractor, Never attempt to start the engine while standing beside the tractor. WARNING: Never use starting fluids, such as ether, as a starting aid. Severe engine damage or fire could result. •...
  • Page 18 DRIVING THE TRACTOR WARNING: Avoid sudden starts, exces- sive speed and sudden stops. WARNING: Do not leave the seat of the tractor without disengaging the PTO and engaging the parking brake. If leaving the tractor unattended, turn the ignition key off and remove key. •...
  • Page 19 BRAKE PEDAL PARKING BRAKE LEVER Figure 15 WARNING: The forward/reverse pedal will not operate when the parking brake is engaged. Do not attempt to force the pedal when the parking brake is engaged; this could cause premature wear or damage to the drive linkage. USING THE HI/LO RANGE SHIFT LEVER WARNING: tractor...
  • Page 20 USING THE HYDRAULIC LIFT LEVER The hydraulic lift system provides power for raising and positioning three point hitch and belly mounted equipment. The system’s position control feature maintains the selected height or depth of the equipment. When the hydraulic lift lever is moved to a higher or lower setting, the system repositions the equipment and maintains that selected position.
  • Page 21 THROTTLE HANDLE LOCK BUTTON Figure 20 • Push the bottom of the switch downward to disengage the PTO. IMPORTANT : Normally the PTO will not operate when the tractor is driven in the reverse direction. The PTO reverse override switch must be activated to operate the PTO while traveling in reverse.
  • Page 22 USING THE THREE POINT HITCH WARNING: Always disengage the PTO, stop the engine, and set the parking brake before dismounting the tractor to connect, disconnect, or adjust three point hitch mounted implements. Use the rear three point hitch system to attach three point mounted implements, which are normally driven by the rear PTO.
  • Page 23 FLOAT HITCH FLOAT BOOM LOWER HITCH LOWER BOOM ANGLE LEFT ROLLBACK BUCKET RAISE HITCH RH FENDER RAISE BOOM COVER Figure 24 ON DEMAND FOUR WHEEL DRIVE The On Demand Four Wheel Drive system automatically delivers power to the front axle whenever the need for additional traction is sensed by the transmission.

  • Page 24: Section 3: Adjustments

    SECTION 3: ADJUSTMENTS ADJUSTING THE SEAT For the comfort of the operator, a single lever adjustable seat is provided to set the fore to aft position of the seat. Adjust the seat to the most comfortable position that allows you to operate all controls and pedals.
  • Page 25 • The length of the upper hitch link is normally determined by the design of each implement. To adjust the upper hitch link, loosen the lock- ing lever and turn the adjustment tube as shown in Figure 28. After the appropriate length is attained, tighten the locking lever.
  • Page 26 ADJUSTING THE BRAKES The tractor brakes are adjusted at the factory and should experience minimal wear if the tractor is operated normally. However, all brake pads are subject to wear and at some point the brake linkage may have to be adjusted. Check the brake linkage as follows: •...

  • Page 27: Section 4: Tractor Maintenance

    SECTION 4: MAINTENANCE The service life and reliability of any machine depends upon the care it is given. Proper lubrica- tion and maintenance is a vital part of that care. Using the Lubrication and Maintenance Chart as a guide, monitor the hourmeter on the instrument panel to ensure the required maintenance proce- dures are performed.
  • Page 28 LUBRICATION AND MAINTENANCE CHART (ILLUSTRATION)

  • Page 29: Lubrication And Maintenance Chart

    LUBRICATION AND MAINTENANCE CHART Ref. Operation to be Performed Check Engine Oil Level Check Air Cleaner Check Engine Coolant Level Check and Clean Radiator Screen and Oil Cooler Fins Change Engine Oil and Replace Oil Filter Retorque Front and Rear Wheel Bolts Check Transmission Oil Level Replace Hydraulic and...
  • Page 30 ACCESSING THE ENGINE COMPARTMENT WARNING: If the tractor has been recently operated, engine surfaces (including the radiator) will be HOT. Allow the engine to cool before open- ing the hood, or use extreme caution to avoid burns when the hood is open. To raise the hood, locate the latch release lever in the hood notch at the front of the tractor.
  • Page 31 • Because battery acid is corrosive, do not pour it into any sink or drain. Before discarding an empty electrolyte container, rinse it thoroughly with a neutralizing solution. • NEVER connect (or disconnect) battery charger clips to the battery while the charger is turned on, as it can cause sparks.
  • Page 32 HEAD LIGHT BULB REPLACEMENT The tractor is equipped with four headlight bulbs. If one of the bulbs should burn out, replace the bulb as follows: • Fully raise the hood so that the hood prop cylinders hold the hood in the raised position. •...
  • Page 33 INSTRUMENT PANEL BULB REPLACEMENT Referring to the instrument panel information pro- vided in the CONTROL AND FEATURES section of this manual, regularly check to ensure that the instrument panel light bulbs are functioning. To change a burned out instrument panel bulb: •...
  • Page 34 Main Fuse The main fuse in the tractor wire harness protects the tractor’s entire electrical system. A blown main fuse will prevent battery current from passing though the harness. To replace the main fuse: • Raise the tractor hood and remove the right side panel.
  • Page 35 • If the oil level is low, add Cub Cadet hydraulic oil. Loosely position a funnel in the fill hole so that there is enough clearance around the fun- nel to allow the transmission to vent while the oil is poured into the transmission. Fill ONLY to the full mark, never overfill the transmission.
  • Page 36 CHANGING HYDROSTATIC TRANSMISSION AND HYDRAULIC SYSTEM OIL FILTERS NOTE: With the exception of the first oil filter change after the 25 hour break-in period, the hydrostatic transmission and hydraulic system oil filters should be changed along with the hydrostatic transmission/hydraulic system oil after every 200 hours of operation.
  • Page 37 CHECKING OIL LEVEL IN FRONT AXLE AND FINAL REDUCTION GEAR CASES. Check the front axle and final reduction gear case oil levels after every 50 hours of operation. Check the oil level only while the engine is stopped and the tractor is standing on a level surface. Check Front Axle Oil The oil fill plug/dipstick is located on the left side of the axle housing.
  • Page 38 • Place a suitable container beneath the front of the axle housing. • Remove the oil fill plug/dipstick to help vent the axle, then remove the drain plug and allow the oil to drain into the container. Reinstall the drain plug after draining the oil.
  • Page 39 TIRE MAINTENANCE Check the tire air pressure after every 50 hours of operation or weekly. Keep the tires inflated to the recommended pressures. Improper inflation will shorten the service life of a tire. See the tire side wall, or the Tire Inflation chart, for proper inflation pressures.
  • Page 40 3. Clean the engine and the entire tractor thoroughly. 4. Fill the fuel tank with FRESH high grade Number Two diesel fuel. 5. Remove the glow plugs and pour a small amount of engine oil into each cylinder. Reinstall the glow plugs and slowly crank the engine to distribute the oil.

  • Page 41: Section 5: Engine Information And Maintenance

    SECTION 5: ENGINE INFORMATION AND MAINTENANCE Daihatsu L.L.C., the California Air Resources Board (CARB) and the United States Environmental Protection Agency (U.S. EPA) (Owner’s Defect Warranty Rights and Obligations) EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED MODEL YEAR 2001 AND LATER ENGINES WHICH ARE PURCHASED AND USED IN CALIFORNIA, AND TO CERTIFIED MODEL YEAR 2001 AND LATER ENGINES WHICH ARE PURCHASED AND USED ELSEWHERE IN THE UNITED STATES California And United States Emission Control Defects Warranty Statement...
  • Page 42 Daihatsu Emission Control Defects Warranty Provisions The following are specific provisions relative to your Emission Control Defects Warranty Coverage. It is in addition to the Daihatsu engine warranty for non-regulated engines. Warranted Parts — Coverage under this warranty extends only to the parts listed below (the emission control systems parts) to the extent these parts were present on the engine purchased.
  • Page 43 ENGINE MAINTENANCE WARNING: Use care when servicing any component in the engine area. If the engine has recently been operated, components will be hot and could cause burns. Allow the engine to cool before servicing. WARNING: Before servicing the engine, place the tractor on a level surface, stop the engine, engage the parking brake, and remove the key from the...
  • Page 44 ADDING ENGINE OIL WARNING: Never overfill the engine crankcase. The engine may overheat and/or damage may result if the oil in the crankcase is below the “ADD” mark or over the “FULL” mark on the dipstick. For best results, fill to the “FULL”...
  • Page 45 • Place a suitable container below the drain plug to collect the old oil. Turn the drain plug counter- clockwise to remove from the engine. • Allow the old oil to completely drain from the engine crankcase into the container below. •...
  • Page 46 • Wait a few minutes to allow as much air as possible to escape through the filler neck, then reinstall the radiator cap. • Fill the overflow reservoir to the "FULL" mark. • Start the engine and allow it to run for a short period.
  • Page 47 • Pull the air cleaner element from the housing. See Figure 59. CLEANER ELEMENT Figure 59 • Lightly blow or brush loose debris from the air cleaner element. Clean any debris from the housing. • Inspect the paper pleats of the cleaner element for damage and dirt.
  • Page 48 Changing The Fuel Filter Replace the fuel filter cartridge after every 600 hours of operation. NOTE: There is no shut off valve in the fuel system. To stop the flow of fuel while replacing the filter, it will be necessary to carefully clamp the fuel line between the fuel tank and the filter.

  • Page 49: Section 6: Specifications

    SECTION 6: SPECIFICATIONS Engine Manufacturer............Diahatsu Horsepower .

  • Page 50: Specifications

    SPECIFICATIONS Hydraulic Lift System Type ............Auxiliary Pump-Gear Control .

  • Page 51: Section 7: Optional Equipment And Accessories

    SECTION 7: OPTIONAL EQUIPMENT AND ACCESSORIES When purchasing your tractor, you probably had it equipped for your particular needs at that time. You may later wish to obtain additional equipment or accessories to perform other tasks. Refer to the chart below for a list of optional equipment and accessories currently available through your Cub Cadet dealer.

  • Page 52: Warranty

    Proper maintenance of your Cub Cadet equipment is the owner’s responsibility. Follow the instructions in your owner’s manual for correct lubricants and maintenance schedule. Your Cub Cadet dealer carries a complete line of genuine Cub Cadet parts and quality lubricants and filters for your equipment’s engine, transmission, chassis and attachments. This limited warranty covers any defect in materials or workmanship in your Cub Cadet compact tractor and Cub Cadet attachments from the date of purchase for the first user purchaser.

Table of Contents