Page of 26

Acer P223W User Manual

Acer lcd monitor quick setup guide.
Also See for P223W:
Quick start manual - 27 pages
Service manual - 37 pages
Safety Instructions
Observe the folowing safety guidelines when connection and using your monitor:
·
Be sure that your monitor is electrically rated to operate with the AC power available in
·
Locate your monitor near an easily accessible electrical outlet.
·
Place the monitor on a solid surface and treat it carefully. The screen can be damaged if dropped, sharply hit, or touched
with a sharp or abrasive implement.
·
Put your monitor in a location with low humidity and a minimum of dust.
·
Never use your monitor if the power cable has been damaged. Do not allow anything to rest on the power cable, and keep
the cable away from where people could trip over it.
·
Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock.
·
To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor's case.
·
Be sure to hold the plug, not the cable, when disconnecting the monitor from an electrical outlet.
·
Openings in the monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be
blocked or covered. Also, avoid using the monitor on a bed, sofa, rug, or other soft surface.
·
Doing so may block the ventilation openings in the bottom of the cabinet. If you put the monitor in a bookcase or some
other enclosed space, be sure to provide adequate ventilation.
·
Do not expose the monitor to rain or use it near water. If the monitor accidentally gets wet, unplug it and contact an
authorized dealer immediately. You can clean the exterior of the monitor with a damp cloth when necessary, but be sure
to unplug the monitor first. If your monitor does not operate normally-in particular, if there are any unusual sounds or smells
coming from it -unplug the monitor immediately and contact an authorized dealer or service center.
Connecting Your Monitor to a Computer
1.Connect Video Cable
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the video cable to the computer.
c. (only Dual-Input Model) Connect one end of the 24-pin DVI cable to the back of the
end to the computer's port.
2. Connect power cord
Connect the power cord to the monitor, then to a properly grounded AC outlet.
3. Connect the Audio Cable.(optional)
4. Power-ON Monitor and Computer
Power-ON the monitor first, then power-ON the computer.
This sequence is very important.
5. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose the problem.
No Power - The monitor's power indicator is off.
Make sure the monitor power cable is fully inserted in the monitor's power port and the electrical outlet.
Test the electrical oulet by plugging in a working electrical device such as a lamp.
Try another power cable on the monitor. You can use the computer's power cable to perform this test.
No Video - The monitor's power indicator is on but theere are no
image on the screen.
Ensure that the video connector is properly connected to the computer.
Ensure that the computer is on and functioning properly.
Turn off the monitor and check the video cable pins. Make sure no pins are bent.
Operationg Detail
Please refer to user's guide in CD-ROM packaged with this monitor
your location.
monitor and connect the other
LC D Mo n i to r Qu ick Se tu p Gu id e
P223W

   Also See for Acer P223W

   Related Manuals for Acer P223W

   Summary of Contents for Acer P223W

  • Page 1

    Turn off the monitor and check the video cable pins. Make sure no pins are bent. Operationg Detail Please refer to user’s guide in CD-ROM packaged with this monitor P223W your location. monitor and connect the other LC D Mo n i to r Qu ick Se tu p Gu id e...

  • Page 2

    This Class B digital apparatus complies with Canadian ICES-003. Remarque à l’intention des utilisateurs canadiens Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada. P223W LC D Mo n i to r Qu ick Se tu p Gu id e...

  • Page 3

    汞(Hg) 镉(Cd) 六价铬(Cr P223W 多溴联苯 多溴二苯醚 ) (PBB) (PBDE)...

  • Page 4

    48 Watts D-Sub DVI-D 24pin (Only Dual-Input Model) Analog:0.7Vp-p(standard), 75 OHM, Positive Digital signal (Only Dual-Input Model) Horizontal : 473.76mm Vertical : 296.1mm 100~240VAC,50~60Hz LC D Mo n i to r Qu ick Se tu p Gu id e P223W...

  • Page 5

    Language OSD position . timeout Auto configuration (only Analog input model) Input signal Selection (only Dual input model) DDCCI On/Off Display information Reset Exit LC D Mo n i to r Qu ick Se tu p Gu id e P223W...

  • Page 6: Table Of Contents

    TABLE OF CONTENTS Special notes on LCD monitors ... 1 Information for your safety and comfort ... 2 Unpacking ... 5 Attaching/Removing the base ... 6 Screen position adjustment ... 6 Connecting the power cord ... 7 Safety precaution ... 7 Cleaning your monitor ...

  • Page 7: Special Notes On Lcd Monitors

    · Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours. EN-1 P223W...

  • Page 8: Information For Your Safety And Comfort

    After setting the volume level, do not increase it afteryour ears adjust. • Limit the amount of time listening to music at high volume. • Avoid turning up the volume to block out noisy surroundings. • Turn the volume down if you can’t hear people speaking near you. EN-2 P223W...

  • Page 9

    Observe the following tips: • refrain from staying too long in one fixed posture • avoid slouching forward and/or leaning backward • stand up and walk around regularly to remove the strain on your leg muscles EN-3 P223W...

  • Page 10

    Warning! We do not recommend using the product on a couch or bed. If this is unavoidable, work for only short periods, take breaks regularly, and do some stretching exercises. ----------------------------------------------------------------------------------------------------- For more information and help in recycling, please visit the following websites: http://global.acer.com/about/sustainability.htm Worldwide: EN-4 P223W...

  • Page 11: Unpacking

    · LCD Monitor · D-Sub Cable · User Manual · DVI Cable (Only Dual-Input Model) · Quick Start Guide EN-5 P223W · AC Power Cord...

  • Page 12: Attaching/removing The Base, Screen Position Adjustment

    The monitor can be adjusted to 15 degrees up or 5 degrees down as indi- cated by arrow below. Remove: Depress the release button as indicated first before removing the base and follow the arrow direction to remove it. EN-6 P223W...

  • Page 13: Connecting The Power Cord, Safety Precaution, Cleaning Your Monitor

    Refrain from giving shock or scratch to the screen, as screen is fragile. CLEANING YOUR MONITOR Please carefully follow the below guidelines when cleaning the monitor. · Always unplug the monitor before cleaning. · Use a soft cloth to wipe the screen and cabinet front and sides. EN-7 P223W...

  • Page 14: Power Saving

    P223W Power saving The monitor will be driven into Power Saving” mode by the control signal from the display controller, as indicated by the amber-color power LED. State Light Blue Power Saving Amber Mode The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated.

  • Page 15: Connector Pin Assignment

    CONNECTOR PIN ASSIGNMENT 15-Pin Color Display Signal Cable PIN NO. DESCRIPTION Monitor Ground DDC-return R-Ground G-Ground B-Ground PIN NO. Green Blue EN-9 P223W DESCRIPTION Logic Ground Monitor Ground DDC-Serial Data H-Sync V-Sync DDC-Serial Clock...

  • Page 16

    DDC Clock DDC Data TMDS Data1- TMDS Data1+ TMDS Data 1/3 Shield Meaning +5V Power GND(return for +5V hsync.vsync) Hot Plug Detect TMDS Data0- TMDS Data0+ TMDS Data 0/5 Shield TMDS Clock Shield TMDS Clock+ DDC TMDS Clock- EN-10 P223W...

  • Page 17: Standard Timing Table

    800 x 600 832 x 624 74.55 Hz VESA 1024 x 768 VESA 1024 x 768 VESA 1024 x 768 VESA 1152 x 864 VESA 1280 x 960 VESA 1280 x 1024 VESA 1280 x 1024 VESA 1680 x 1050 EN-11 P223W...

  • Page 18: Installation

    3. Power-ON Monitor and Computer Power-ON the monitor first, then power-ON the computer. This sequence is very important. 4. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose the problem. EN-12 P223W...

  • Page 19: User Controls

    P223W USER CONTROLS Front Panel Controls 1.Power Switch: To turn ON or OFF the power. 2.Power LED: Lights up to indicate the power is turned ON. 3.Empowering / Exit: 1) When OSD menu is in active status, this button will act as EXIT-KEY(EXIT OSD menu).

  • Page 20: How To Adjust A Setting

    P/X Series OSD behave When user press “MENU” button on front bezel Acer eColor Management If selected to “Acer eColor Management “ item, will appear the Acer eColor” OSD USER If selected to “USER” item, will appear the Standard OSD I.

  • Page 21

    · ADJUSTING THE PICTURE The descriptions for function control LEDS Acer eColor Management Main Menu Menu icon icon User mode Text mode Standard USER Main Menu Menu icon icon Contrast Brightness Menu item User defined. Settings can be fine-tuned to...

  • Page 22

    Adjust the horizontal position. (available in Analog mode only) Adjust the vertical position. (available in Analog mode only) Set the color temperature to warm white. Set the color temperature to cool white. Adjusts Red/Green/Blue intensity. Multi-language selection. EMEA version OSD only EN-16 P223W...

  • Page 23

    Select input signal from digital(DVI) (only Dual-Input Model) Turn ON/OFF DDC/CI support Show the resolution, H/V frequency andinput port of current input timing. Clear each old status of Auto- configurationand set the color temperature to Cool. Save user adjustment and OSD disappear. EN-17 P223W...

  • Page 24

    Operation instructions Acer eColor Management Step 1: Press “ Key “ to open the Acer eColor Management OSD and access the scenario modes Step 2: Press “<“ or “>” to select the mode Step 3: Press “ Auto Key “ to confirm the mode and run Auto Adjust ·...

  • Page 25: Troubleshooting

    Using OSD, in case of missing full-screen image, please select other resolution or other vertical refresh timing. · Wait for a few seconds after adjusting the size of the image before changing or disconnecting the signal cable or powering OFF the monitor. EN-19 P223W...

  • Page 26

    Check the power switch. · Check if AC power cord is properly connected to the monitor. · Check if video signal cable is properly connected at the back of monitor. · Check if the power of computer system is ON. EN-20 P223W...

This manual also for:

P223, X203hbd, X203w

Comments to this Manuals

Symbols: 0
Latest comments: