Motorola RDU2080d User Manual
  1. Manuals
  2. Brands
  3. Motorola Manuals
  4. Two-Way Radio
  5. RDU2080d - RDX Series On-Site UHF 2 Watt 8 Channel Two Way Business...
  6. User manual

Motorola RDU2080d User Manual

Motorola two-way radio user guide
Hide thumbs Also See for RDU2080d:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Motorola RDU2080d

Summary of Contents for Motorola RDU2080d

  • Page 2 Motorola, the Stylized M Logo, and all other trademarks indicated as such herein are Trademarks of Motorola, Inc. Reg. U.S. Pat. & Tm. Off. © 2007 Motorola, Inc. All rights reserved.

  • Page 3: Table Of Contents

    CONTENTS Contents......1 Safety ......5 Batteries and Chargers Safety Information.
  • Page 4 Getting Started ..... 32 Turning radio ON/OFF....32 Adjusting volume .
  • Page 5 RDX UHF Frequencies Chart... . 72 RDU2080d - UHF Default Frequencies Chart ......76 RDU4160d - UHF Default Frequencies Chart .
  • Page 6 Software Applications ....88 Cables ......88 Chargers .

  • Page 7: Safety

    ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website which lists approved accessories: http://www.motorola.com/RDX English...

  • Page 8: Batteries And Chargers Safety

    Motorola-authorized batteries. Other batteries may explode, causing personal injury and damage. Use of accessories not recommended by Motorola may result in risk of fire, electric shock, or injury. English To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when disconnecting the charger.

  • Page 9: Operational Safety Guidelines

    OPERATIONAL SAFETY GUIDELINES • Turn the radio OFF when charging battery. • The charger is not suitable for outdoor use. Use only in dry locations/conditions. • Connect charger only to an appropriately fused and wired supply of the correct voltage (as specified on the product).

  • Page 10: Introduction

    INTRODUCTION Thank you for purchasing the Motorola® RDX Series™ Radio. This radio is a product of Motorola's 75 plus years of experience as a world leader in the designing and manufacturing of communications equipment. The RDX Series™ radios provide cost-effective...
  • Page 11 For a copy of a large-print version of this user guide or for product-related questions, contact: 1-800-448-6686 in the USA 1-800-461-4575 in Canada 1-866-522-5210 on your TTY (Text Telephone) For product information visit us at: www.motorola.com/radios/business or visit our microsite at: www.motorola.com/RDX English...

  • Page 12: Fcc Licensing Information

    FCC LICENSING INFORMATION INTERFERENCE INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. RDX Series™ Business two-way radios operate on radio frequencies that are regulated by the Federal Communications Commission Faxed contact the Fax-On- Demand...
  • Page 13 Motorola Product Services at: 1-800-448-6686 Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments...

  • Page 14: Radio Overview

    RADIO OVERVIEW PARTS OF THE RADIO Antenna Microphone Use ‘Menu’ button to lock keypad Front Buttons English Lithium-Ion On/Off/ Battery Volume Knob LED Indicator Accessory Connector Model Label to scroll up/ down through channels and menu setting PTT (Push-to-Tal Button SB1 - Monitor Button SB2 - Nuisance...

  • Page 15: On/Off/Volume Knob

    Indicates the model of the radio Microphone Speaks clearly into the microphone when sending a message. Antenna For Models RDU2080d and RDV2080d, the antennas are non-removable antenna. For RDU4160d, the antenna is removable. LED Indicator Used to give battery status, power-up status, radio call information and scan status.

  • Page 16: Side Buttons

    • Programmable Button Default set to generate the current programmed call tone. • Programmable Button Default set to preset Channel 1 • Programmable Button Default set to preset Channel 2 Note: A short press of either preset button (B or C) tunes the radio to the preset channel and the radio will play a good chirp.
  • Page 17 The radio’s model is Frequency Model Band RDV2080d RDU2080d RDU4160d shown on the front of the radio, underneath the speaker, and tells you the following information: Transmit Number of...

  • Page 18: Battery Features

    25% discharge, lasts even longer. Motorola batteries are designed specifically to be used with a Motorola charger and vice versa. Charging in non-Motorola equipment may lead to battery damage and void the battery warranty. The battery should be at about 77°F (25°C) (room temperature),...

  • Page 19: Battery Recycling And Disposal

    Contact your local waste management agency for specific requirements and information in your area. Motorola fully endorses and encourages the recycling of Li-Ion batteries. In the U.S. and Canada, Motorola participates in the nationwide Rechargeable Battery Recycling Corporation (RBRC) program for Li-Ion battery collection and recycling.

  • Page 20: Installing The Lithium-Ion (Li-Ion)

    Installing the Lithium-Ion (Li-Ion) Battery slots Turn OFF the radio. With the Motorola logo side up on the battery pack, fit the tabs at the bottom of the battery into the slots at the bottom of the radio’s body. Press the top part of the battery towards the radio until a click is heard.

  • Page 21: Alkaline Battery Pack

    Alkaline Battery Pack (Optional Accessory) Installing Alkaline Batteries Turn OFF the radio, if it is turned ON. Remove Li-Ion battery. Assemble alkaline battery pack in the same steps as installing the Li-Ion battery pack. Remove battery door from alkaline battery pack. Slide the 5 AA alkaline batteries into the frame, matching the markings inside the compartment Removing Alkaline Batteries...

  • Page 22: Attaching And Removing Antenna

    Attaching and Removing Antenna These instructions apply ONLY for RDU4160d radio. Do not attempt to remove the antenna if your radio is not one of these models. Attaching the Antenna Align the threaded end of the antenna with the radio’s antenna connector. Turn the antenna clockwise to fasten it.

  • Page 23: Installing Spring Action Belt Clip

    Installing Spring Action Belt Clip Slide the spring action belt clip rails into the belt clip grooves on the back of the battery pack and slide it down until the belt clip tab snaps into place. To remove, pull back the metal release tab on the belt clip tab and push the spring action belt clip upward to remove.

  • Page 24: Battery Life Information

    Battery Life Information When the Battery Save feature is ON (enabled by default) the battery life will be longer. The following chart summarizes battery life estimations: Battery Type Standard High Ultra High Note: Battery life is estimated based on 5% transmit/ 5% receive/ 90% standby standard duty cycle English Li-Ion Battery Life with Battery Save feature ON...

  • Page 25: Alkaline Battery Life

    Alkaline Battery Life The following chart estimates the Alkaline battery life: Battery Save Feature Notes: • Battery life are being estimated based on 5% transmit/ 5% receive/ 90% standby standard duty cycle. • * When using Alkaline battery, the radio is set to 2W by default Alkaline Battery Life 5 Watts 4 Watts...
  • Page 26 Battery Meter The battery meter located in the upper left corner of the display indicates how much battery power you have remaining. Battery Type Li-Ion English RDX Series™ Battery Meter 3 Bars 2 Bars 100%-70% 70%-30% 100%-70% 70%-30% 1 Bar 30%-0% 30%-0%...

  • Page 27: Charging The Battery

    Rapid Charger. The radio comes equipped with a Standard Charger. To charge the battery (with the radio attached), place it in a Motorola-approved Drop-in Tray Single Unit Charger or Drop-in Tray Multi Unit Charger. Note: When acquiring additional chargers or...
  • Page 28 Charging a Standalone Battery To charge only the battery - at step 4, insert the battery into the tray, with the inside surface of the battery facing the front of the charger, as shown. Ensure the slots in the battery correctly engage in the charger Note: Ensure that the bracket in the charger is...
  • Page 29 Charging a High Capacity or Ultra High Capacity Battery Removable Removable Piece To convert the charger from the default setup to accommodate the High capacity or Ultra High capacity battery: Squeeze both tabs on each side of the removable bracket in the drop-in charger tray and lift the bracket from the charger tray.
  • Page 30 Drop-in Tray Charger LED Indicators Status Steady red indication for 3 Power ON seconds Charging Blinking red (slow) Charging Steady red indication Complete Battery Fault(*) Blinking red (fast) Notes: • (*) Normally re-seating the battery pack will correct this issue. •...
  • Page 31 Rapid Charger LED Indicator Status LED Status Steady green indication for 3 Power ON seconds Charging Blinking green Top-off Charging Blinking green (slow) Charge Steady green indication Complete Battery Fault (*) Blinking red (fast) Waiting to Double-blink yellow Charge (**) indications Notes: •...
  • Page 32 Estimated Charging Time The following table provides the estimated charging time of the battery. For further details, see “Battery” on page 87. Charging Solution Standard Charging Solution Rapid Charging Solution English Estimated Charging Time Battery Type Standard High Capacity 7 hours 12 hours 1.5 hours 3 hours...
  • Page 33 Charging a Radio and Battery using a Multi Unit Charger- MUC (Optional Accessory) The Multi Unit Charger (MUC) allows drop-in charging of up to 6 radios or batteries. Batteries can be charged with the radios or removed and placed in the MUC separately. Each of the 6 charging pockets can hold a radio or battery, but not both.

  • Page 34: Getting Started

    GETTING STARTED For the following explanations refer to "Parts of the radio" on page page 12. TURNING RADIO ON/OFF Turn the On/Off/Volume knob clockwise to turn ON the radio. The radio will chirp and the LED will briefly blink a red light. To turn the radio OFF rotate the On/Off/Volume knob counterclockwise until you hear a ‘click’...

  • Page 35: Selecting A Channel

    SELECTING A CHANNEL Your radio offers different number of conventional channels depending on the model number. To select a channel, press the toggle buttons until you reach the desired channel. Program each channel separately. Each channel has its own Frequency, Interference Eliminator Code and Scan Settings.

  • Page 36: Signal Strength Indicator And Channel Busy Indicators

    Up to 250,000 Sq. Ft. Up to 20 Floors VHF 2W Up to 220,000 Sq. Ft. Up to 13 Floors To talk with someone on your two-way radio, the channel, frequency, and interference eliminator code must be the same on both...
  • Page 37 Frequency: The frequency your radio uses to transmit/receive. Interference Eliminator Code: These codes help minimize interference by providing you with a choice of code combinations. Scramble Code: Codes that make your transmissions sound garbled to anyone listening who is not set to that specific code. Bandwidth: Some frequencies have selectable channel spacing, which must match other radios for optimum audio quality.

  • Page 38: Radio Led Indicators

    RADIO LED INDICATORS RADIO STATUS Channel Alias Edit Channel Busy Cloning Mode Cloning In Progress Fatal Error at Power up Low Battery Low Battery Shutdown Monitor Power-Up ‘Idle’ Programming Mode / Channel Mode Scan Mode Transmit (Tx)/Receive (RX) Transmit in Low Power Select Note: Channel Alias Edit only applies to Display Models English...

  • Page 39: Hands-Free Use/Vox

    To transmit, speak into accessory microphone and to receive, stop talking. You can disable VOX operation by pressing the PTT button or removing the audio accessory. Note: To order accessories, call 1-800-422-4210, or contact your Motorola point of purchase. English...

  • Page 40: Hands Free Without Accessories

    PTT button. Note: • The iVOX feature is available only on display models RDU2080d, RDV2080d, and RDU4160d. • To learn how to set VOX/iVOX sensitivity levels refer ahead to ‘Menu Options’ in this section.

  • Page 41: End Of Transmission Tone (Roger Beep Tone)

    End of Transmission Tone (Roger Beep Tone) Short press the SB1 button while turning ON the radio to enable/disable End of Transmission Tone. Note: This setting is set to OFF by default Keypad Beeps Keypad Beeps can be enabled/disabled by short pressing SB2 button (until radio ‘chirps’) while turning ON the radio.

  • Page 42: Setting Vox / Ivox Sensitivity

    Setting VOX / iVOX sensitivity The VOX/iVOX sensitivity can be adjusted via the MENU as well as the CPS. To modify via the MENU, first make sure you have enabled either VOX or iVOX (See “Hands-Free Use/ VOX” on page 37.). Once VOX/iVOX has been enabled, short press MENU.
  • Page 43 Battery Type Menu Only if the battery pack is not detected, the radio will allow changes to the battery type setting from either Lithium-Ion or Alkaline.To change the setting, press the MENU button as many times as needed until the radio blinks the current battery type (either ‘LITHIUM’...

  • Page 44: Programming Features

    PROGRAMMING FEATURES ENTERING PROGRAMMING MODE To enter ‘Programming Mode’, press and hold both the PTT button and the SB1 button simultaneously for three seconds, while turning ON the radio. A unique tone will sound, indicating that the radio has entered ’Programming Mode’...

  • Page 45: Programming Rx (Reception) Frequencies

    • If you're in ‘Idle’ Programming Mode and wish to exit the ’Programming Mode’, long press the PTT button to return to normal radio operation. • Whenever the radio wrap around to the beginning of the Programming Mode options the changes will be automatically saved, even if you turn OFF the radio.

  • Page 46: Programming Rx (Reception) Codes

    PROGRAMMING RX (RECEPTION) CODES (CTCSS/DPL) Once you have chosen the channel you want to program, short press the PTT button or MENU to scroll through the options until you reach the ‘Code Programming Mode’. The radio display will show the blinking CTCSS/DPL code as follows: To program the desired code, scroll up/down with the...

  • Page 47: Programming Scramblel

    To program the desired bandwidth (HI = 25 kHz, LOW = 12.5 kHz), use the until to select the value. Long press the PTT button to exit and save or short press the PTT button to move to the next programming feature without saving.

  • Page 48: Programming Maximum Number Of Channels

    PROGRAMMING MAXIMUM NUMBER OF CHANNELS You can configure the maximum number of channels for the radio. Once you have entered ’Programming Mode’ scroll up/down by short pressing the PTT button until you reach the ‘Max Channel Programming Mode’:. The radio display will blink the current maximum number of channels programmed.

  • Page 49: Programming Microphone Gain Level

    radio will sound the call tone selected (except for setting ‘0’). Once you have selected the tone you want to program, long press the PTT button to exit and save or short press the PTT button to move to the next programming feature without saving Note: The values available for Call Tones are...

  • Page 50: Programming Microphone Accessory

    PROGRAMMING MICROPHONE ACCESSORY GAIN LEVEL To configure the Accessory Microphone Gain Level, enter ’Programming Mode’ and scroll through the programming options by short pressing the PTT button. The current accessory microphone gain level setting will be blinking. You can select the desired gain level (1=Low gain,2= Medium gain or 3= High gain) by pressing the buttons.
  • Page 51 transmitting without having to switch channels by pressing PTT. • To stop scanning, short press the SB2 button again. • If you press the PTT button while the radio is scanning, the radio will transmit on the channel which was selected before you activated Scan.

  • Page 52: Programming Buttons

    Once you have selected the channel, proceed to enable (‘YES’) or disable (‘NO’) the scan feature by toggling the SB2 (*) button. Once you have set the values you need, long press the PTT button to save an exit. Notes: •...
  • Page 53 name. If you want to exit the Channel Aliasing Mode long press the PTT button. • A cursor will blink at the end of the channel name. Use button B to move the cursor to the left. If you're in the first character, the radio will give you a bonk tone.

  • Page 54: Nuisance Channel Delete

    NUISANCE CHANNEL DELETE Nuisance Channel Delete allows you to temporarily remove channels from the ‘Scan List’. This feature is useful when irrelevant conversations on a ‘nuisance’ channel tie up your radio's scanning features. To delete a channel from the scan list: •...

  • Page 55: Cps (Computer Programming Software)

    Please refer to Features Summary Chart Section at the end of the user guide for details. Notes: • (**) CPS Programming Cable (P/N RKN4155)is an accessory sold separately. Please contact your Motorola Point of Purchase for more information. English...

  • Page 56: Bandwidth Select

    Bandwidth Select Default setting for Bandwidth Select depends on the specific frequency and channel. For details refer to ‘Frequencies and Codes Charts’ Section.Some frequencies have selectable channel spacing, which must match other radios for optimum audio quality. Time-Out Timer When PTT button is pressed, transmissions can be terminated by setting up a 'time-out’...

  • Page 57: Call Tones

    Call Tones See “Programming Call Tones” on page 46. Scramble See “Programming Scramble Reverse Burst Reverse Burst eliminates unwanted noise (squelch tail) during loss of carrier detection. You can select values of either 180/240. Notes: • The features described are just some of the features CPS has.

  • Page 58: Cloning Radios

    CLONING RADIOS You can clone RDX™ Series radio profiles from one radio (the ‘Source’ radio) to a second radio (the ‘Target’ radio) by using any one of these 3 methods: • One Multi Unit Charger (optional accessory) • Two Single Unit Chargers and a Radio-to- Radio cloning cable (optional accessory) •...
  • Page 59 Notes: • Paired target radios and source radios must be of the same type in order for cloning to run successfully. • (*) MUC pockets numbers should be read from left to right with the Motorola logo facing front. English...

  • Page 60: Cloning Radios Using The Radio To Radio (R2R) Cloning Cable (Optional Accessory)

    Cloning Radios using the Radio to Radio (R2R) Cloning Cable (optional accessory) Operating Instructions Source Radio: Radio to be cloned. Target Radio: Radio to which the configuration of the “Source Radio” will be copied (cloned). Before beginning the cloning process, make sure you have: •...
  • Page 61 (display/non display), same region and same transmission power). Note: This cloning cable is designed to operate only with compatible Motorola RLN6175 (Standard) and RLN6304 (Rapid) Single Unit Chargers. When ordering Cloning Cable please refer to P/ N RLN6303. For details about accessories refer to Accessories section.

  • Page 62: Cloning Radios Using The Cps (Computer Programming Software)

    Cloning Radios using the CPS (Computer Programming Software) To clone RDX™ radios using the CPS software, you will need to have available the CPS, a Drop-in Charger Tray and the CPS Programming Cable. Information on how to clone using the CPS is available either in •...
  • Page 63 To program the Frequency TX, scroll through the radio options until your display shows: To program the desired frequency, scroll using buttons until you get the desired frequency code value. Long press the PTT button to exit and save or short press the PTT button to go to the next programming feature without saving.
  • Page 64 To program the Bandwidth TX scroll down/up with the buttons until you get the following screen: To program the desired bandwidth (HI = 25 kHz, LOW = 12.5 kHz), toggle the buttons to select the value. Long press the PTT button to exit and save or short press the PTT button to go to the next programming feature without saving.

  • Page 65: Troubleshooting

    TROUBLESHOOTING Symptom Recharge or replace the Li-Ion battery. Reposition or replace AA batteries. No Power Extreme operating temperatures may affect battery life. Refer to See “About the Li-Ion Battery” on page 16. Confirm Interference Eliminator Code is set. Frequency or Interference Eliminator Code may be in use. Hearing other noises or Change settings: either change frequencies or codes on all radios.
  • Page 66 Symptom Limited talk range Message not transmitted or received English Try This... Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease range. Check for clear line of sight to improve transmission. Wearing radio close to body such as in a pocket or on a belt decreases range. Change location of radio.
  • Page 67 Symptom Radios are too close; they must be at least five feet apart. Heavy static or interference Radios are too far apart or obstacles are interfering with transmission. Refer to “Talking and Monitoring” on page 33. Recharge or replace Li-Ion battery. Replace AA batteries. Low batteries Extreme operating temperatures affect battery life.
  • Page 68 Symptom Cannot activate VOX Battery does not charge although it has been placed in the drop-in charger for a while Note: Whenever a feature in the radio seems to not correspond to the default or preprogrammed values, check to see if the radio has been programmed using the CPS with a customized profile. English Try This...

  • Page 69: Use And Care

    USE AND CARE Use a soft damp cloth to clean the exterior If the radio is submerged in water... Turn radio OFF and remove batteries Do not immerse Do not use alcohol or in water cleaning solutions Dry with soft cloth Do not use radio until completely dry English...

  • Page 70: Frequency And Code Charts

    The charts in this section provide Frequency and Code information. These charts are useful when using Motorola RDX Series™ two-way radios with other business radios. Most of the frequency’s positions are the same as Spirit M, GT, S, and XTN Series Frequencies.
  • Page 71 • (*) Due to FCC regulations these frequencies (six in total) are different from the previous Motorola Legacy Series radios. This means that if you select the RDX radio in one of these frequencies the radio will not inter-operate with an XTN radio. In order for a RDX radio to inter-operate with an XTN radio, make sure you choose any of the frequencies (21 in total) that are common for both radios.

  • Page 72: Chart

    RDV2080d - VHF DEFAULT FREQUENCIES CHART The following are the default frequencies programmed in your RDX Radio. Note that the VHF default frequencies programmed in Channels 1 and 2 are different from the XTN Series default values. In order for a RDX radio to inter-operate with an XTN radio, you must make sure you choose any of the frequencies (21 in total, read User Guide for details) that are common for both radios.

  • Page 73: Making Xtn Compatible With Rdx Radios - Quick Instructions

    MAKING XTN COMPATIBLE WITH RDX RADIOS - QUICK INSTRUCTIONS The following instructions are a quick and easy way to make your XTN (XV1100, XV2100 and XV2600 models) compatible with RDX Series™ default frequencies: Make sure your XTN is programmed to the factory default frequencies (Turn your radio ON while holding the MENU and PTT buttons simultaneously for three seconds).

  • Page 74: Rdx Uhf Frequencies Chart

    RDX UHF FREQUENCIES CHART Frequency Frequency # (MHz) 464.5000 464.5500 467.7625 467.8125 467.8500 467.8750 467.9000 467.9250 461.0375 461.0625 461.0875 461.1125 461.1375 English RDX UHF Frequencies (cont.) Bandwidth Frequency # 12.5/25.0 kHz 12.5/25.0 kHz 12.5 kHz 12.5 kHz 12.5/25.0 kHz 12.5/25.0 kHz 12.5/25.0 kHz 12.5/25.0 kHz 12.5 kHz...
  • Page 75 RDX UHF Frequencies (cont.) Frequency Frequency # Bandwidth (MHz) 462.8625 12.5 kHz 462.8875 12.5 kHz 462.9125 12.5 kHz 464.4875 12.5 kHz 464.5125 12.5 kHz 464.5375 12.5 kHz 464.5625 12.5 kHz 466.0375 12.5 kHz 466.0625 12.5 kHz 466.0875 12.5 kHz 466.1125 12.5 kHz Frequency Frequency #...
  • Page 76 Frequency Frequency # (MHz) 467.8375 467.8625 467.8875 467.9125 469.4875 469.5125 469.5375 469.5625 462.1875 462.4625 462.4875 462.5125 English RDX UHF Frequencies (cont.) Bandwidth Frequency # 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz...
  • Page 77 Frequency Frequency # Bandwidth (MHz) 452.5375 452.4125 452.5125 452.7625 452.8625 456.1875 456.2375 456.2875 456.3375 Notes: • (*) Frequency limited to 2W maximum power output • When referring to XTN radios, note that frequencies from # 57 to # 89 are 33 new additional frequencies RDX UHF Frequencies (cont.) Frequency # 12.5 kHz...

  • Page 78: Chart

    RDU2080d - UHF DEFAULT FREQUENCIES CHART RDX UHF 8 CH Radios Default Frequencies - RDU2080d Channel Note: Compatible with XTN radios English Frequency Frequency # (MHz) 464.5500 467.9250 467.8500 467.8750 461.0625 461.1125 461.1625 461.2125 Code # Code Bandwidth 67.0 Hz 25.0 kHz...

  • Page 79: Chart

    RDU4160d - UHF DEFAULT FREQUENCIES CHART Default frequencies for the RDU4160d are fully compatible with the AXU4100 radios (AX Series). If you need to make this radio compatible with XTN series, please re-program RDU4160d frequencies to match XTN UHF frequencies defaults RDX UHF 16 CH Radios Default Frequencies - RDU4160d Channel Frequency #...
  • Page 80 RDX UHF 16 CH Radios Default Frequencies - RDU4160d (cont.) Channel Note: Compatible with AXU4100 radios series (AX series) English Frequency Frequency # (MHz) 461.3625 462.4875 462.5375 462.0375 464.0875 464.1375 Code # Code Bandwidth 74.4 Hz 25.0 kHz 79.7 Hz 25.0 kHz 85.4 Hz 25.0 kHz...

  • Page 81: Ctcss And Pl/Dpl Codes

    CTCSS AND PL/DPL CODES CTCSS 67.0 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 Note: (*) New CTCSS code. CTCSS Codes CTCSS CTCSS 107.2 110.9 114.8 118.8 127.3 131.8 136.5 141.3 146.2 151.4 156.7 162.2 167.9 173.8 179.9 186.2...
  • Page 82 Code English PL/DPL Codes (cont.) Code Code...
  • Page 83 PL/DPL Codes (cont.) Code Code Code English...

  • Page 84: Programming Customized Frequencies On 4W/5W Rdx Models

    VHF and UHF charts in previous pages). VHF range is 146 -174 MHz and UHF 438 - 470 MHz. Certain 4W/5W models can also be programmed to work with repeaters. Please contact your Motorola point of purchase for details. English...

  • Page 85: Motorola Limited Warranty For The United States And Canada

    This limited warranty is a consumer's exclusive remedy, and applies as follows to new Motorola Products, Accessories and Software purchased by consumers in the United States, which are accompanied by this written warranty.
  • Page 86 (c) use of the Products or Accessories for commercial purposes or subjecting the Product or Accessory to abnormal usage or conditions; or (d) other acts which are not the fault of Motorola, are excluded from coverage. English Use of Non-Motorola Products and Accessories.
  • Page 87 Accordingly, any copyrighted software contained in the Motorola products may not be modified, reverse-engineered, distributed, or reproduced in any manner to the extent allowed by law.
  • Page 88 Motorola or any third party software provider, except for the normal, non- exclusive, royalty-free license to use that arises by operation of law in the sale of a product.

  • Page 89: Accessories

    ACCESSORIES ANTENNAS Part No. Description UHF Stubby Antenna 450-470 RAN4033 VHF Helical Antenna 146-174 RAN4041 UHF Whip Antenna 438 - 470 RAN4031 AUDIO ACCESSORIES Part No. Description 53815 Headset w/Boom Mic BR 53862 Remote Speaker Mic BR 53863 Earpiece w/Mic BR Part No.

  • Page 90: Carry Accessories

    CARRY ACCESSORIES Part No. RLN6302 Hard Leather Carry Case RLN6307 Spring Action Belt Clip POWER SUPPLIES AC PIN ADAPTORS Part No. RLN6349 North America AC Pin Adaptor SOFTWARE APPLICATIONS Part No. Computer Programming RVN5147 Software (CPS) English CABLES Description Part No. RLN6303 RKN4155 CHARGERS...

  • Page 91: Power Supplies

    RLN6170 Rapid Exchg AC pin Pwr Supply Attention: Certain accessories may be or may not be available at the time of purchase. For latest information on accessories, contact your Motorola point of purchase or visit: www.motorola.com/RDX or www.motorola.com/ radios/business (*) Americas Rapid Charging Kit includes Power Supply, Drop-in Tray Charger, and AC Pin adaptors.

  • Page 92: Rdx Series™ Features Summary

    RDX Series™ Features Summary Programmable Via RADIO PANEL Features Non- Display Display Backlight Bandwidth Select Battery Save Battery Type Buttons Reset Programmable via Default Value Non- Display Display 5 Seconds Frequency Dependable Li-Ion Programming Tips Choose the backlight’s time out by using the CPS. Front panel programming available only on display models by entering Programming Mode (1).
  • Page 93 Programmable Via RADIO PANEL Features Non- Display Display Call Tones (4) Channel Aliasing Channels Programmable via Default Value Non- Display Display OFF / BUTTON A Model Dependant Programming Tips Front panel radio programming available only for Display Models by going into Programming Mode(1).
  • Page 94 Programmable Via RADIO PANEL Features Non- Display Display Cloning Mode CPS Manager Lock End of Tx Tone (or Roger Beep) Frequencies Programmable via Default Value Non- Display Display Channel and Model Dependant Programming Tips Enables radio to enter cloning mode in order to clone its profile settings into other radios (using Radio to Radio Cloning Cable or Multi-Unit Charger).
  • Page 95 Programmable Via RADIO PANEL Features Non- Display Display Frequencies, Direct Input Bandwidth Range Codes, Interference Eliminator Codes (CTCSS/DPL) IVOX, enable/ disable IVOX, sensitivity Level Programmable via Default Value Non- Display Display Any value within radio frequency band Model Dependant Channel and Model Dependant HIGH (Level 3)
  • Page 96 Programmable Via RADIO PANEL Features Non- Display Display Keypad Beep ( or Keypad Tone) (2) Keypad Lock LEDs Enabled/ Disabled Low Battery Alert - Shutdown Maximum Channels (2) Microphone Gain Level, ACCESSORY Programmable via Default Value Non- Display Display UNLOCKED Enabled Model and CPS programmable...
  • Page 97 Programmable Via RADIO PANEL Features Non- Display Display Microphone Gain Level, RADIO Monitor (4) Nuisance Ch Delete (4) PL Defeat Programmable via Default Value Non- Display Display Medium (Level 2) SB1 Button SB2 Button SB1 Button Programming Tips For front panel programming enter Programming Mode (1).
  • Page 98 Note: There may be power restrictions depending on the frequency chosen in each channel. Text that shows up in the radio display when turned ON. Default text is MOTOROLA. Programmable via CPS. Available only for RDU4160d model. Allows to restore radio's factory defaults. Press PTT, SB1, SB2 simultaneously for 3 seconds while turning ON radio.
  • Page 99 Programmable Via RADIO PANEL Features Non- Display Display Scan Scan List Scan, Auto Scan Scramble (4) Time-Out Timer Programmable via Default Value Non- Display Display SB2 Button ON - All Channels (level 0) 60 seconds Programming Tips Short press SB2 to enable/disable scan. Use CPS for editing Scan List (adding/removing channels to be scanned).
  • Page 100 (2) Using CPS you can prevent this feature to be programmed via front panel radio. (3) Contact your Motorola Point of purchase for enabling this feature and/or for radio models details. (4) For Non-Display Models, feature can be enabled for front panel programming by assigning feature to SB1 or SB2. For Display models: Feature can be enabled to any of the programmable buttons rather than the default ones.

  • Page 101: Programmable Buttons Chart

    Programmable Buttons Chart Scan / Button Monitor Nuisance Delete Default Default BUTTON A (*) BUTTON B (*) BUTTON C (*) Notes: • Buttons come programmed to default functions. Using CPS you can assign one of the features shown in the chart, so the button can toggle values using radio front panel •...

  • Page 102: Icons Chart

    Icons Chart Icon Symbol Battery Level Channel Code Frequency Keypad lock Program Scan Scramble Comments Displayed during normal radio mode operation, displays battery life remaining Displayed during normal radio operation and when programming channel features Displayed during normal radio operation and when programming codes features Displayed during normal radio operation and when programming frequency features Displayed whenever the Keypad lock feature is enabled (keypad is locked) Displayed whenever the radio is set up to Programming Mode.
  • Page 103 Strength Repeater(*) Vox/IVox (*) Available only for 4160d model. To enable, contact your Motorola point of purchase. Comments Displayed whenever the channel is transmitting or set to a high-power selection RSSI Display Icon numbers of bars will indicate the strength of the received signal.
  • Page 105 © 2007 Motorola Inc. All rights reserved. Motorola Technology Sdn Bhd (Co. No. 455657-H) Plot 2 Bayan Lepas Technoplex Industrial Park Mukim 12 S.W.D 11900 Penang, Malaysia Printed in Malaysia September 2007 *6880309T01* 6880309T01-A...

This manual is also suitable for:

Rdx rdv2080dRdx series

Table of Contents