Motorola MVME5100 Series Specification Sheet page 2

SDRAM Expansion
L2 Cache
1MB or 2MB
SDRAM Expansion
60x MPC7400
Arbiter MPC750
ECC SDRAM
64, 128 or 512MB
Vcore
REG
Hawk ASIC
100 MHz Memory Bus
+3.3V
REG
64-bit/33 MHz Local PCI Bus
PCI
PMC2
Expansion
P2
M V M E 5 1 0 0 P 2 I / O
M V M E 5 1 0 0 P 2 I / O
I/O Compatibility
Historically, MCG has offered two tracks in its PowerPC VME
portfolio. The first track (which includes the MVME2600/
2700) provides typical single-board computer I/O features
including Ethernet, SCSI, multiple serial ports, a parallel port,
and a single PMC slot. The on-board I/O is routed to P2 and
made available to the user via MCG's MVME761 or
MVME712M transition boards. The second track (which
includes the MVME2300/2400) offers limited on-board I/O
(Ethernet and a single serial port both via the front panel) but
provides dual PMC slots enabling maximum user I/O custom-
ization.
The MVME5100 merges the best features of both tracks
enabling the OEM to support varying I/O requirements with
the same base platform, simplifying part number mainte-
nance, technical expertise requirements, and sparing.
P2 I/O Modes
The MVME5100 supports two, jumper-configurable P2 I/O
modes, PMC mode and IPMC mode.
PMC mode is backward compatible with the MVME2300/
MVME2400. In PMC mode, 64 pins from PMC Slot 1 and 46
pins from PMC Slot 2 are available on P2 for PMC rear I/O.
In IPMC mode, the MVME5100 supports legacy MVME761 or
MVME712M I/O modules (with limited PMC I/O) when an
IPMC761 or IPMC712 PMC card is populated in PMC Slot 1.
In this configuration, PMC Slot 2 contains some signals that
are reserved for extended SCSI.
IPMC Modules
The IPMC761 and IPMC712 are optional add-on PMC mod-
ules that provide backward compatibility with previous-gener-
ation MCG products (such as MVME2600 and MVME2700)
256MB
Flash
Serial
64 or 256MB 1MB 16550
Flash
Serial
16MB
16550
BUF
X-Bus
RTC
NVRAM
FP I/O FP I/O
PMC1 VME
Universe2B
MVME5100 Block Diagram
Serial
RJ-45
Ethernet
82559ER
Ethernet
RJ-45
82559ER
RJ-45
P1
using the MVME761 or MVME712M transition board. IPMC
modules provide rear I/O support for
• one single-ended Ultra Wide SCSI port
• one parallel port
• four serial ports (2 or 3 async and 1 or 2 sync/async,
depending on module)
With this PMC card configuration, the memory mezzanine,
one PMC slot, and the PMCspan are still available, providing
support for OEM product customization.
T r a n s i t i o n M o d u l e s
MVME761
The MVME761 transition module provides industry-standard
connector access to the IEEE 1284 parallel port, a 10BaseT
or 100BaseT port via an RJ-45 connector, two DB-9 connec-
tors providing access to the asynchronous serial ports config-
ured as EIA-574 DTE, and two HD-26 connectors providing
access to the sync/async serial ports. These serial ports,
labeled as Serial 3 and Serial 4 on the faceplate of the
MVME761, are individually user-configurable as EIA-232,
EIA-530, V.35, or X.21 DCE or DTE via the installation of
Motorola Serial Interface Modules (SIMs).
A P2 adapter provides interface module signals to the
MVME761 transition module. The 3-row P2 adapter can be
used for 8-bit SCSI. A 5-row P2 adapter supports 16-bit SCSI
and PMC I/O.
MVME712M
The MVME712M transition module provides industry-stan-
dard connector access to the Centronics
row SCSI port, and four DB-25 connectors providing access
to the asynchronous/synchronous serial ports jumper config-
urable as EIA-232 DCE or DTE. A P2 adapter provides inter-
PMC P11 & P12
PCI
PIB
WB-554
ISA
SCSI Super I/O ESCC
LSI National 85230
PMC P14 & P15
IPMC Block Diagram
T r a n s i t i o n M o d u l e s
®
parallel port, a nar-
CIO
8536
P2 MUX
PAL
(IPMC761)