Our product has been tested in typical configuration by Ecom Sertech Corp and was found to comply with the essential requirement of “Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility” (89/336/EEC; 92/31/EEC; 93/68/EEC) http://www.sapido.com.tw/ User Manual v1. 0.0...
Blin king 10Mbps Ethernet Tx/ Rx activity 120ms 10/ 100Mbps Ethernet is connected Blin king 100Mbps Ethernet Tx/Rx act ivity LAN x 1 LAN port activity Green 30ms Blin king 10Mbps Ethernet Tx/ Rx activity 120ms http://www.sapido.com.tw/ User Manual v1. 0.0...
Connect BR070N to xDSL/ Cable modem with the Ethernet cable, WAN to LAN. Turn on your Computer. Network setup After the network connection is built, the next step is setup the router with proper network http://www.sapido.com.tw/ User Manual v1. 0.0...
Double-click Network and Dial-up Connections icon, double click Local Area Connection, and Local Area Connection Properties window will appear. Select “Internet Protocol (TCP/IP)”, then click “Properties”. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. http://www.sapido.com.tw/ User Manual v1. 0.0...
Double-click Network and Internet Connections icon, click Network Connections, then double-click Local Area Connection, Local Area Connection Status window will appear, and then click “Properties”. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. http://www.sapido.com.tw/ User Manual v1. 0.0...
Connections. Right-click Local Area Network, then select “Properties”. Local Area Connection Properties window will appear, select “Internet Protocol Version 4 (TCP / IPv4)”, and then click “Properties”. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. http://www.sapido.com.tw/ User Manual v1. 0.0...
Router IP Address Lookup After the IP address setup was completed, please clicks “start” → “run” at the bottom-lower corner of your desktop: Input “cmd”, and then click “OK”. http://www.sapido.com.tw/ User Manual v1. 0.0...
Please click “admin” to login the BR070N . Enter the User name and Password in to the blank and then Click Login. The default values for User Name and Password are admin (all in lowercase letters). http://www.sapido.com.tw/ User Manual v1. 0.0...
Internet Connection This Chapter describes how to setup BR070N to the internet. The BR070N is delivered with the following factory default parameters. Default IP address: 192.168.1.1 Default IP subnet mask: 255.255.255.0 Web login user name: admin http://www.sapido.com.tw/ User Manual v1. 0.0...
Enter the User name and Password into the blank and then click Login. The default values for User Name and Password are admin (all in lowercase letters). Status page Download pdadd Logout Home button menu http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 14
Cont rol、IP Filtering、IP Binding and QoS Firmware Upgrade This function allows you upgrade the BR070N firmware to new version. Please note do not power off the devic e during the upload because it may crash the system. Denial of Service http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 15
You can maintain the system time by synchronizing with a public time server over the Internet. Factory Default You could reset the current configuration to factory default. Reboot This function is used to reboot Logout This page is used to logout. http://www.sapido.com.tw/ User Manual v1. 0.0...
The BR070N provides five selections for the Internet Mode type, PPPoE, DHCP, Static IP , PPTP and L2TP and WiFi ISP. Check with your ISP if you don’t know the WAN type. http://www.sapido.com.tw/ User Manual v1. 0.0...
Input the password provided by your ISP. Wireless AP Turn on/ off wireless SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list. 3.3.2 DHCP http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 18
Specific:use BR070n itself mac address Wireless AP Turn on/ off wireless SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list. http://www.sapido.com.tw/ User Manual v1. 0.0...
Input DNS information which is provided by your ISP Wireless AP Turn on/ off wireless SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list. 3.3.4 PPTP http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 20
The MPP C algorithm us es a Lempel-Ziv (LZ) based algorithm with a continuous history buffer, called a dictionar Wireless AP Turn on/ off wireless http://www.sapido.com.tw/ User Manual v1. 0.0...
(OS). Advanced users can set it manually. Wireless AP Turn on/ off wireless SSID Service S et identifier, users can define to any or keep as default. Encryption Select wireless encryption type form the drop-down list. http://www.sapido.com.tw/ User Manual v1. 0.0...
Select wireless encryption type form the drop-down list. If a router is already set at the house, and you want to make the wireless LAN communication. WAN、DHCP、NAT、DDNS、QoS、Firewall、 This mode does not support Static/Dynamic route、VPN Server features. http://www.sapido.com.tw/ User Manual v1. 0.0...
Wireless AP Turn on/ off wireless WiFi AP When you connect to the internet wirelessly through PC and wireless device without WAN、DHCP、NAT、 wireless LAN function equipped. This mode does not support DDNS、QoS、Firewall、Static/Dynamic route、VPN Server features. http://www.sapido.com.tw/ User Manual v1. 0.0...
Chapter 4 GUI Function Setup Status You could check WAN, LAN, Client net work in status. WAN Configuration http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 26
LAN Configuration http://www.sapido.com.tw/ User Manual v1. 0.0...
Allow or block client to access internet Parental Control Control Parental provide URL Filtering and MAC Filter Schedule for setup 4.2.1 URL Filtering URL Filtering is used to restrict users to access specific websites in internet http://www.sapido.com.tw/ User Manual v1. 0.0...
URL Filtering function. 4.2.2 MAC Filter Schedule When enabled, filtering will be based on the MAC address of LAN computers. Any computer with its MAC address on this list will be blocked from accessing the Internet. http://www.sapido.com.tw/ User Manual v1. 0.0...
Please select Enable MAC Filtering to filter MAC addresses. 4.2.3 Wireless Schedule Wireless available schedule, this page allows you setup the wireless schedule rule. Please do not forget to configure systeim before enable this feature http://www.sapido.com.tw/ User Manual v1. 0.0...
Office Control Office control provide Multiple AP 、Wireless Access Control、IP Filtering、IP Binding、QoS 4.3.1 Multiple AP http://www.sapido.com.tw/ User Manual v1. 0.0...
MAC address with a simple comment and click on “Apply Change” to save the new addition. To delete a MAC address, select its corresponding checkbox under the Select column and click on “Delete Selected” button. http://www.sapido.com.tw/ User Manual v1. 0.0...
MAC address any time it requests an IP address. This is almost the same as when a device has a static IP address except that the device must still request an IP address from the DHCP server. http://www.sapido.com.tw/ User Manual v1. 0.0...
The QoS can let you classify Internet application traffic by source/destination IP address and port number. To assign priority for each type of application and reserve bandwidth can let you have a better experience in using critical real time services like Internet phone, video conference …etc. http://www.sapido.com.tw/ User Manual v1. 0.0...
LAN device bandwidt h of download bandwidt h Percentage Add the setting data Delete Selected & Delete Click Delete Selected will delete the selected item. Click Delete All will delet e all items in this table. Firmware Upgrade http://www.sapido.com.tw/ User Manual v1. 0.0...
It provide auto detect new firmware from Internet, and user can select to upgrade new version or not. 4.4.2 Manual upgrade If you download firmware from website, you can upgrade firmware manual as below. It provide 2 kind of Denial of Service: Home and Enterprise http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 36
Home: Item Description Home Home Check “ ” to enable DoS function for prevention. You also can No Prevention check “ ” to disable DoS function. Enterprise: http://www.sapido.com.tw/ User Manual v1. 0.0...
/ computer and office local area network to establish a secure network connection. And User can safe login office local area network and access to personal documents, files Sharing and other resources. It provides the most convenient VPN encryption. http://www.sapido.com.tw/ User Manual v1. 0.0...
Click Delete Selected will delete the selected item. Click Delete All will delet e all items in this table. NAT Management This section contains configurations for the BR070N ’s advanced functions such as: virtual server, and DMZ to provide your network under a security environment. http://www.sapido.com.tw/ User Manual v1. 0.0...
Enter the port number, for example 20-22. Current Port Forwarding It will display all port forwarding regulation you made. Table Delete Selected & Delete Click Delete Selected will delete the selected item. Click Delete All http://www.sapido.com.tw/ User Manual v1. 0.0...
The port forwarding feature is more secure because it only opens the ports required by that application. Item Description Enable DMZ It will enable the DMZ service if you select it. DMZ Host IP Address Please enter the specific IP address for DMZ host. http://www.sapido.com.tw/ User Manual v1. 0.0...
Users can select time zone and synchronize the local clock on the router. Item Description Time Zone Select Please select the time zone. 4.10 Factory Default You could reset the current configuration to factory default. http://www.sapido.com.tw/ User Manual v1. 0.0...
Internet Setup Please refer Internet Setup AP(switch to AP mode) 5.1.2 Please refer WiFi AP(switch to WiFi AP mode) 5.1.3 Please refer WiFi AP 5.1.4 WiFi ISP Please refer WiFi ISP IP Config 5.2.1 5.2.1.1 PPPoE http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 44
DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C Address" http://www.sapido.com.tw/ User Manual v1. 0.0...
Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C Address" Save & Apply Click on Save to save the setting dat e, the Apply button for execute current configuration. 5.2.1.3 Static IP http://www.sapido.com.tw/ User Manual v1. 0.0...
Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MA C Address" Save & Apply Click on Save to save the setting dat e, the Apply button for execute current configuration. 5.2.1.4 PPTP http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 47
The MPP C algorithm us es a Lempel-Ziv (LZ) based algorithm with a continuous history buffer, called a dictionar Select Attain DNS Automatically. Or select Set DNS Manually, if http://www.sapido.com.tw/ User Manual v1. 0.0...
Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually. Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your http://www.sapido.com.tw/ User Manual v1. 0.0...
DHCP Client Range Define the DHCP client range and then the DHCP server will assign an IP to the requesting computer from t his range. The Show Client will display every assigned IP address, MAC address, http://www.sapido.com.tw/ User Manual v1. 0.0...
Select enable to use DDNS function. Each time your IP address to WAN is changed, and the information will be updated to DDNS service provider automatically. Service Provider Choose correct Service Provider from drop-down list, here including http://www.sapido.com.tw/ User Manual v1. 0.0...
User name is used as an identity to login Dynamic-DNS service. Password/Key Password is applied to login Dynamic-DNS servic e. Save & Apply Click on “Save” to save the setting data. The “A pply” button can execute current configuration IPv6 Config Item Description http://www.sapido.com.tw/ User Manual v1. 0.0...
5.4.1 Basic Settings This page is used to configure the parameters for wireless LAN clients who may connect to your Access Point. Here you may change wireless encryption settings as well as wireless network parameters http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 53
Item Description Di sable Wireless Turn off the wireless service. Band Select the frequency. It has 6 options: 2.4 GHz (B/G/N/B+G/G+N/B+G+N). Mode Select the mode. It has 3 modes to select: (AP, Client, WDS, AP+WDS). http://www.sapido.com.tw/ User Manual v1. 0.0...
Each SSID could be set with different data rate, WMM and access type Save & Apply Click on “Save” to save the setting data. The “A pply” button can execute current configuration 5.4.2 Advanced Settings http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 55
Protection Please select to enable wireless protection or not. Aggregation Enable this function will combine several packets to one and transmit it. It can reduce the problem when mass packets are transmitting. http://www.sapido.com.tw/ User Manual v1. 0.0...
“None” to skip the following setting Item Description W E P is t he mos t ge ne r al e nc ry pt i on s c h em e am on g http://www.sapido.com.tw/ User Manual v1. 0.0...
Access Point in a minute without any hassle. SAPIDO BR070N could support both Self-PIN or PBC modes, or use the WPS button (at real panel) to easy enable the WPS function.
Page 58
(2). Fill in the PIN number from the wireless card in Client PIN Number field, and then click “Start PIN”. (3). Click PIN from Adapter Utility to complete the WPS process with the wireless router. http://www.sapido.com.tw/ User Manual v1. 0.0...
The WDS explanation is as the following picture. Router_A: Set the connection mode to “AP+WDS” from “Wireless Basic Setting”, and then select the channel number (in this example is "11”). Click Apply Changes to save the setting. http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 60
Please check the MAC address Enable WDS function from the page – “WDS Setting”, and then fill in the MAC address of Router_B. Click Apply Changes to save the setting data. http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 61
Select encryption for security Rout er_B mac address The WDS AP List will show the WDS device MAC address. Router_B: Setup Router_B WDS. Select encryption for security Rout er_A mac address http://www.sapido.com.tw/ User Manual v1. 0.0...
Rout er_B Rout er_A DHCP Enable Disable Note 1: LA N IP address should be under the same segment but cannot be the same number. 5.4.7 Schedule Please refer Wireless Schedule Please refer NAT Management http://www.sapido.com.tw/ User Manual v1. 0.0...
Enable QoS Check “Enable QoS” to enable QoS function for the WAN port. You also can uncheck “Enable QoS ” to disable QoS function for the WAN port. Automatic uplink speed Check the Automatic uplink speed. http://www.sapido.com.tw/ User Manual v1. 0.0...
It will display all ports that are filt ering now. Delete Selected & Delete Click Delete Selected will delete the selected item. Click Delete All will delet e all items in this table. Port 80 has been blocked as the following illustrate. http://www.sapido.com.tw/ User Manual v1. 0.0...
Motherboard that supports WOL, as well as a Network Controller (NIC) supporting this function. Most of the newer Motherboard (circa 2002 and On), have an On Board NIC that supports WOL. Otherwise you need to install a PCI NIC that is WOL capable. http://www.sapido.com.tw/ User Manual v1. 0.0...
Users can create a backup file that contains current router settings. This backup file can be used to restore router settings. This is especially useful in the event you need to reset the router to its default settings. Save Configuration (1). Click Save http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 68
Please click “Save” to save the configuration to your computer. (3). Select the location which you want to save file, then click Save. Load configuration file (1). Tap “browse” and select configuration file then click Open http://www.sapido.com.tw/ User Manual v1. 0.0...
Please refer Remote Management 5.6.8 Time Zone Users can synchronize the local clock on the router to an available NTP server (optional). To complete this setting, enable NTP client update and select the correct Time Zone. http://www.sapido.com.tw/ User Manual v1. 0.0...
UPnP, please click My Network Places. Users will see an Internet Gateway Device icon. By click the icon, users can enter the GUI of the router. If you do not wish to use UPnP, you can disable it. http://www.sapido.com.tw/ User Manual v1. 0.0...
Disable:do not send any RIP packet out Send RIP 1 packet out Send RIP 2 packet out There are 3 options: Receive Disable:do not rec eive any RIP packet Only receive RIP 1 packet Only receive RIP 2 packet http://www.sapido.com.tw/ User Manual v1. 0.0...
To allow the L2TP net work traffic to be forwarded to its destination without the network address translation tasks. IPV6 Pass-through Allow IPV 6 packet to be forwarded to its destination without the network address translation tasks. http://www.sapido.com.tw/ User Manual v1. 0.0...
Way 1: Check with your Internet Service Provider. Way 2: Check the setting screen of BR070N . Click on Status & Log item to select Network Configuration on the Main Menu. WAN IP is shown on the WAN interface. http://www.sapido.com.tw/ User Manual v1. 0.0...
2. Select never dial a connection, click on Apply button, and then click on OK button. 3. Click on Tools and then click on Internet Options. 4. Click on Connections and then click on LAN Settings. http://www.sapido.com.tw/ User Manual v1. 0.0...
A: BR070N will start to run after the setting finished applying, but the setting isn’t written into memory. Here we suggest if you want to make sure the setting would be written into memory, please reboot the device via Reboot under System Management directory. http://www.sapido.com.tw/ User Manual v1. 0.0...
If the Wireless Router’s Wireless screen is set to Allow LAN access to selected Wireless Stations only, then each of your Wireless stations must have been selected, or access will be blocked. http://www.sapido.com.tw/ User Manual v1. 0.0...
Page 78
A: The default WEP of WinXP is Authentication Open System - WEP, but the WEP of SAPIDO BR070N is only for Shared Key - WEP, it caused both sides couldn’t communicate. Please select the WEP of WinXP from Authentication Open System to Pre-shared Key - WEP, and then the WEP wireless interface between WinXP and SAPIDO BR070N would be communicated.
A: If there are two DHCP servers existing on the same network, it may cause conflict and generate trouble. In this situation, we suggest to disable DHCP server in router and configure your PC manually. http://www.sapido.com.tw/ User Manual v1. 0.0...
FireFox ver. 2.0.0.11 and the following related versions.3. Safari ver. 3.04 and the following related versions. 7.7 Communications Regulation Information Should any consumers need to learn more information, services and supports, please contact the supplier of your product directly. http://www.sapido.com.tw/ User Manual v1. 0.0...