Download Print this page

Moen TUB AND SHOWER VALVES 2290 Installation Instructions

Tub and shower valves

Advertisement

Quick Links

MODELS 2290, 2291, 2600, 2700, 5401, 62600, 62700, 72615, 72700
and MODEL SERIES T471, T473, T555, T666, T777 & T888
TUB AND SHOWER VALVES
Connections are either 1/2 inch I.P.S. pipe or 1/2 inch copper sweat connections.
If the Moen Slip Fit spout is used, a 1/2 inch copper drop and lookout may be used.
Measurements
These are shown in the drawings. The depth measurement is critical. Use
the front face of the plaster ground as a reference point for the finished
wall position, including tile (2-1/16" [52mm]). The center line of the supply
and discharge piping should be a maximum of 2-3/16" (56mm) and a minimum
of 1-7/16" (37mm) behind the finished wall surface.
HANDLE
UP
CAUTION:
Before turning water on during either rough-in or trim-out, make sure that cartridge retainer clip is in place. The
cartridge and retainer clip were properly installed and tested before leaving the factory. Although it is unlikely, it is
nevertheless possible that through the handling of the valve by any number of persons the retainer clip may not be
properly installed. This should be carefully checked at time of rough-in and trim-out. If the retainer clip is not properly
installed, water pressure could force the cartridge out of the casting. Personal injury or water damage to the
premises could result.
®
Available with three or four port castings, with and without stops.
HANDLE
KNOB
COVER
WASHER
HANDLE
HANDLE
LEVER
SCREW
TEMPERATURE
HANDLE ASSEMBLY
Always turn water off before disassembling the valve. Open valve handle to
alleviate water pressure to insure that complete water shut-off has been
accomplished.

INSTALLATION INSTRUCTIONS

THESE INSTRUCTIONS MUST BE
TUB/SHOWER
COMBINATION
PLASTER
GROUND
ESCUTCHEON
ADJUSTABLE
LIMIT STOP
FLOOR
LEFT WITH HOMEOWNER
IMPORTANT: SEE FLUSHING
INSTRUCTIONS PAGE 2
FINISHED WALL
OR SHOWER
LINE
2-1/16"
(52mm)
6' 6"
(1981mm)
1-1/4"
(32mm)
SUPPLY
32"
(813mm)
CAUTION
USE 1/2"
IRON PIPE
SIZE
MINIMUM
OR 1/2"
TUBING.
CLIP
EAR
MT620J
TUB FILLER
2-1/16"
(52mm)
SUPPLY
15/16"
(24mm)
45"
(1143mm)
48"
(1219mm)

Advertisement

loading

Summary of Contents for Moen TUB AND SHOWER VALVES 2290

  • Page 1: Installation Instructions

    Available with three or four port castings, with and without stops. Connections are either 1/2 inch I.P.S. pipe or 1/2 inch copper sweat connections. If the Moen Slip Fit spout is used, a 1/2 inch copper drop and lookout may be used. Measurements These are shown in the drawings.
  • Page 2 (117mm) ➤ 6" FOR I.P.S. (152mm) CAUTION These valves are equipped with Moen's long-life 1225 cartridge, de- signed for smooth, trouble free operation. When soldering, do not heat valve any higher than necessary to flow the solder. Over- heating may damage the cartridge or rubber stop valves.
  • Page 3 Turn "OFF" both hot and cold water supplies, then open faucet to relieve pressure. Remove handle cover from handle knob. Take out handle screw and remove handle knob, washer, and stop tube. Lift out retainer clip. Rotate cartridge shell back and forth with Moen cartridge twist wrench, grasp the cartridge stem with pliers, and pull out the cartridge.
  • Page 4 MT620J AUG '96 Cleaning & Care Instructions for Special Finish Models: (800) BUY - MOEN (289-6636) ®  25300 Al Moen Dr., North Olmsted, OH 44070-8022 U..S.A. © Moen Incorporated 1996 Printed in U.S.A...

This manual is also suitable for:

22912600270054016260062700 ... Show all