Page of 33

Mitsubishi LVP-X80U User Manual

Mitsubishi user manual lcd projector lvp-x80u.
LCD
Projector
User Manual
X 8 0
LVP-X80U
MODEL
EN – 1

   Related Manuals for Mitsubishi LVP-X80U

   Summary of Contents for Mitsubishi LVP-X80U

  • Page 1

    Projector User Manual X 8 0 LVP-X80U MODEL EN – 1...

  • Page 2

    CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE IN- STALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interfer- ence with radio and television reception.

  • Page 3: Table Of Contents

    To operate projector power ON ... 13 Menu operation ... 15 Picture adjustment ... 18 Specification of RGB signals in each computer mode of the projector ... 20 Advanced feature for presentation ... 21 Expand ... 21 PinP (Picture in Picture) ... 21 Still ...

  • Page 4: Important Safeguards

    Water and moisture Do not use this projector near water or in con- tact with water. Accessories Do not place this projector on an unstable cart, stand, tripod, bracket or table.

  • Page 5

    Air outlet grill. The heated Air outlet grill and Bottom plate may cause injury or damage to other equipment. Also, do not set the projector on the desk which is easily affected by heat. Clean the air-filter once a month.

  • Page 6: Overview

    Overview Control panel AUTO POSITION POWER COMPUTER SOURCE LAMP VIDEO VOLUME MENU TEMP Terminal board S-VIDEO COMPUTER OUT COMPUTER IN RS-232C VIDEO IN VIDEO AUDIO L AUDIO R EN – 6 Air inlet grill (Front) Front height adjuster button Air inlet grill (Side) Terminal board Speaker Remote control sensor (Front)

  • Page 7

    RADIATION IS EMITTED FROM THIS APERTURE. Adjustment foot (right and left) Lamp cover Adjustment foot (up and down) Caution: Do not replace the lamp right after using the projector. The lamp is very hot. Transmitter indicator Power button SOURCE button Mouse button...

  • Page 8: Using The Remote Control, Battery Installation

    The range for operation is about 10 m (33 feet) when the remote control points to the projector. The distance to the screen back to the projector must be less than 6 m (20 feet). Depending on the type of the screen, the distance is different.

  • Page 9: Installation

    Installation Orientation of the projector Picture size can be set by changing the distance between the screen and the projector. Front projection Screen (between the screen and the head of the projector) Screen Diagonal size Height inches Width feet (inch)

  • Page 10: Basic Connections, Projector + Av Equipment, Projector + Dvd Player Or Hdtv Decoder

    Basic connections This projector can be connected to equipment such as PC, VCRs, video cameras and DVD players. Important: • Make sure that your equipment is turned off before connection. • Plug in firmly and unplug by holding the plug, not by pulling the AC power cord.

  • Page 11: Projector + Personal Computer

    Please contact your dealer. • The audio input for this projector is a stereo pin jack. (Speaker output is mono.) Please check the available cable for the audio input terminal of the PC. Some personal computer may not have the audio output terminal.

  • Page 12: Preparing The Projector For Operation

    2. Connect the power cord to the wall power outlet. 3. Remove the lens cap. Warning: • Do not look directly into the lens when projector is “ON”. • The lens cap is for protecting the lens. If you leave the power on with the cap on, the cap may be warped.

  • Page 13: To Operate Projector Power On

    VIDEO VOLUME TEMP 1. Turn on the equipment connected to the projector. 2. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. • The POWER indicator blinks red for 2, 3 seconds after the power switch ON.

  • Page 14

    • After the lamp is turned off, the lamp cannot be switched on again for 60 seconds as a precaution- ary measure. If you wish to turn on the projector again, wait until the indicator is off then press the POWER button.

  • Page 15: Menu Operation

    Menu operation IMAGE CONTRAST BRIGHTNESS COLOR MATRIX USER COLOR TEMP. SHARPNESS TINT COLOR INSTALLATION KEYSTONE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN IMAGE REVERSE FEATURE MENU POSITION EXPAND MODE FRAME POSITION AUDIO MODE VIDEO SIGNAL ANAMORPHIC LANGUAGE RESET ALL SIGNAL MEMORY CALL HORIZ.POSITION...

  • Page 16

    In this case, use the remote control to turn on the lamp. AUTO POWER OFF .. Use to select the length of time before projector switches to stand-by when there is no input signal selected source. SPLASH SCREEN . Use to display the splash screen on the screen when the power is turned ON.

  • Page 17

    HORIZ. POSITION ... Use to adjust the horizontal position of the image. VERT. POSITION ... Use to adjust the vertical position of the image. FINE SYNC..Use to synchronize the projector with PC input signals so that the image is not blurred.

  • Page 18: Picture Adjustment

    The white, which temperature is low, becomes raddish white. When the color temperature is higher, the white becomes more bluish. This projector sets this color temperature by changing the numbers of contrast blue and red.

  • Page 19

    Adjustment from personal computer Although this projector sets proper signal systems automatically for the image signal from personal computers, it cannot be applied to some of personal computers. In this case, press the AUTO POSITION button. If the images are still not projected correctly, use the MENU display to adjust the projected im- ages.

  • Page 20: Specification Of Rgb Signals In Each Computer Mode Of The Projector

    Picture adjustment (continued) Specification of RGB signals in each computer mode of the projector Signal mode resolution (H x V) TV60 – TV50 – 1080i – 720p – PC98 640 x 400 CGA70 640 x 400 CGA85 640 x 400...

  • Page 21: Advanced Feature For Presentation, Expand, Still

    Advanced features for presentation Expand By pressing the EXPAND button on the remote con- trol, you can magnify the detailed image of the picture. You can also view the screen displaying the picture as its original size (native resolution display). Setting the Expand mode 1.

  • Page 22: Mouse Remote Control

    Mini DIN 6P • Turn off PC and the projector before connecting with PS/2 port. When connecting the PC with the projector when the personal computer is on, the remote control does not work as a mouse. In that case, turn the projec- tor on, then restart the personal computer.

  • Page 23: Lamp Replacement

    • Be sure that the projector guide is firmly inserted between the right and left lamp guides. Important: • The projector will not turn on if you do not secure the lamp lid. • You must reset the operation time meter after you replace the lamp.

  • Page 24: Maintenance

    Maintenance Caution: Be sure to turn off the projector and unplug the power cord from the wall outlet before you perform any main- tenance on the projector. Cleaning the air-filter Clean the air-filter frequently. If the filter or ventilation grill become clogged with dirt or dust, the temperature inside the projector may rise and shut off the power (the TEMP indicator starts to blink red).

  • Page 25: Troubleshooting

    (In this case, the TEMP indicator does not light up.) The image is • The projector is not at a right angle to the screen. distorted. The image is dark. • Brightness, tint and color are not adjusted correctly.

  • Page 26: Indicators

    Indicators The projector has three LED Indicators which shows the working condition of the projector. The following offers solutions to possible problems. If a problem persists, turn the projector off and consult your dealer. POWER indicator LAMP indicator TEMP indicator...

  • Page 27: Specifications, Kensington Lock

    (performance guarantee) Kensington Lock This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact to Kensington Technology Group as shown below.

  • Page 28: Connectors, Dimensional Drawings, What's Included In The Box, Replacement Part

    (Option / Not included in the box) Spare Mercury lamp EN – 28 RS-232C input Use to control the projector with the personal computer, or control the personal computer with remote control. provided RS-232C cable (Mini DIN 8P-D-SUB 9P) for the connection.

  • Page 29

    Manufactured by Mitsubishi Electric Corporation 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan 871D312B10 Printed in Japan...

  • Page 30

    LCD Projector LVP-X80U Control projector by using a personal computer This projector can be controlled by connecting a personal computer with RS-232C terminal. Functions can be controlled by a personal computer: • Turn the ON or OFF • Changing input signals •...

  • Page 31

    (1) Send the command from a personal computer to the projector. (The commands must be sent at least 400ms apart.) (2) The projector will send a return command 400ms* after it has received an end code. If the command is not received correctly, the projector will not send the return command.

  • Page 32

    INPUT COMPUTER INPUT VIDEO When a personal computer sends the command, data code will not be attached. On the other hand, the projector which has received a command will attach the recent operating status and then send. [Example ] Input was Video when the operating status of the input terminal was confirmed.

  • Page 33

    000 - 383 000 - 510 000 - 510 0 (MUTE OFF), 1 (MUTE ON) Status code from projector 30 30 41 50 4F 4E 30 0D '0' '0' 'A' 'P' 'O' 'N' '1' ' Status code from projector 30 30 50 2B 31 30 2B 30 30 2D 30 35 0D...

Comments to this Manuals

Symbols: 0
Latest comments: