Sign in today to find solutions:

Don't have an account? Sign up

Mitsubishi WD-57732 Owner's Manual

Mitsubhishi digital electronics dlp hdtv owner's guide.

 
DLP™ HIGH-DEFINITION TELEVISION
MODELS
WD-Y57aa
WD-Y65
WD-57732
WD-65732
WD-73732
OWNER'S GUIDE
For questions:
-
Call Consumer Relations at 800-332-2119.
-
E-mail us at MDEAservice@mdea.com.
-
Visit our website at www.mitsubishi-tv.com.
For information on Demo Mode and System Reset, please see the back cover.
To order replacement or additional remote controls, lamp cartridges, or Owner's Guides, visit
our website at www.mitsuparts.com or call 800-553-7278.
Guidelines for setting up and using your new widescreen TV start on page 34.
��

Summary of Contents

  • Page 1

    DLP™ HIGH-DEFINITION TELEVISION MODELS WD-Y57aa WD-Y65 WD-57732 WD-65732 WD-73732 OWNER’S GUIDE • For questions: Call Consumer Relations at 800-332-2119. E-mail us at MDEAservice@mdea.com. Visit our website at www.mitsubishi-tv.com. • For information on Demo Mode and System Reset, please see the back cover.

  • Page 2

    WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. FCC Declaration of Conformity Product: Projection Television Receiver Models: WD-Y57, WD-Y65, WD-57732, WD-65732, WD-73732 Responsible Party: Mitsubishi Digital Electronics America, Inc. 9351 Jeronimo Road Irvine, CA 92618-1904 Telephone: (800) 332-2119 This device complies with Part 15 of the FCC Rules.

  • Page 3

    Record the model number, serial number, and purchase date of your TV. The model and serial numbers are on the back of the TV. Refer to this page when requesting assistance with this TV. MODEL NUMBER (check one): WD-Y57 WD-Y65 SERIAL NUMBER PURCHASE DATE Retailer Information RETAILER NAME LOCATION WD-57732 WD-65732 WD-73732...

  • Page 4: Table Of Contents

    Contents Important Information About Your TV General Warnings and Cautions, Notes on Installation and Operation Cleaning Recommendations Important Safeguards ..............Chapter 1: Television Overview Package Contents .

  • Page 5: Table Of Contents

    ..............Mitsubishi DLP™ Projection Television Limited Warranty Index .

  • Page 6

    To Purchase a Replacement Lamp After Warranty Visit our website at www.mitsuparts.com or call to highlight the (800) 553-7278. Order a new lamp by part number as shown below. TV Model Number WD-Y57, WD-Y65, WD-57732, WD-65732 WD-73732 Stand Model MB-57GB MB-65GB MB-57GB MB-65GB...

  • Page 7: Cleaning Recommendations

    Cleaning Recommendations Normally, light dusting with a dry, non-scratching duster will keep your TV clean. If cleaning beyond this is needed, please use the following guidelines: First, turn off the TV and unplug the power cord from the power outlet. Top and Sides of the TV •...

  • Page 8: Important Safeguards

    Important Safeguards Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instruc- tions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference.

  • Page 9

    Important Safeguards, continued 12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

  • Page 11

    Television Overview Package Contents Special Features of Your TV TV Front Panel ........TV Back Panel .

  • Page 12: Package Contents, Special Features Of Your Tv

    High-Definition Video Inputs Component Video Inputs, two on models WD-Y57 and WD-Y65; three on models WD-57732, WD-65732, and WD-73732. Also called Y/Pb/Pr inputs, these inputs receive standard analog video formats of 480i, 480p, 720p, and 1080i high-definition signals. This 1.

  • Page 13

    NetCommand-controlled home-theater system. Memory Card Reader (models WD-57732, WD-65732, WD-73732) You can display a slide show of your favorite JPEG pic- tures or listen to MP3 or WMA audio selections recorded on compatible memory cards.

  • Page 14: Tv Front Panel

    S-VIDEO jack, the VIDEO jack is deactivated. Memory Card Reader (models WD-57732, WD-65732, WD-73732) The memory card reader has four card slots that accept a variety of popular memory card types. The reader lets you...

  • Page 15

    Front-Panel Indicators Steady On Slow Blinking LAMP Indicator LED Color TV Condition Normal TV on or standby condition. None TV just powered off and lamp is Green cooling. 1. Lamp access door is open or Yellow not secure. 2. No lamp installed. Lamp no longer illuminates and has reached the end of the lamp life.

  • Page 16: Tv Back Panel

    ANT 1 is used for CableCARD™ service. COMPONENT inputs 1 and 2 offered on models WD-Y57 and WD-Y65. COMPONENT inputs 1, 2, and 3 offered on models WD-57732, WD-65732, and WD-73732. ������������������ ����������������������������������� ����� �����������������������...

  • Page 17

    TV Back Panel, continued 4. COMPONENT Inputs (COMPONENT 1 and 2 on WD-Y57, WD-Y65; COMPONENT 1–3 on WD-57732, WD-65732, WD-73732) (Audio and Video) Y Pb Pr (480i/480p/720p/1080i) Use these jacks to connect devices with component video outputs, such as DVD players, external HDTV receivers, or compatible video game systems.

  • Page 18: Cablecard™ Technology

    CableCARD™ Technology CableCARD is a nationwide system standard that allows your local cable TV provider to supply you with an access card customized to your account. This card allows your TV to receive, decode, and unscramble the premium digital channels included in your cable TV subscription without the use of a cable box.

  • Page 19

    TV Connections Connection Types ........Digital Video and Home Recording HDTV Cable Box or Satellite Receiver with Component Video Standard Cable Box, Satellite Receiver, or Other Device with S-Video...

  • Page 20: Connection Types

    Connection Types Video and Combined Audio/Video Connections These descriptions apply to TV video only and do not cover signals from personal computers. Picture Quality Name (most sources) HDMI Best (carry high- definition video when available) Component Video Good S-Video Fair Composite Video IEEE 1394 Fair to Best...

  • Page 21: Digital Video And Home Recording, Hdtv Cable Box Or Satellite Receiver With Component Video

    Digital Video and Home Recording The table below will help you decide which type of connection to use for digital video. Digital video comes to your home in a compressed state, whether received on recorded media (e.g., disc) or broadcast over the air, over cable, or via satellite.

  • Page 22: Standard Cable Box, Satellite Receiver, Or Other Device With S-video

    Standard Cable Box, Satellite Receiver, or Other Device with S-Video Required: S-Video cable and left/right analog stereo audio cables. Connect the cable from the outside cable or satellite service to CABLE IN or SATELLITE IN on the cable box or satellite receiver. 2.

  • Page 23: Antenna With A Single Lead, Antennas With Separate Uhf And Vhf Leads

    Antenna with a Single Lead A. For an antenna with flat twin leads A 300-ohm-to-75-ohm transformer is required. This is not included with the TV, but is available at most electronics stores. A1. For an antenna with flat twin leads, connect the 300- ohm twin leads to the 300-ohm-to-75-ohm trans- former.

  • Page 24: Vcr To An Antenna Or Wall Outlet Cable

    VCR to an Antenna or Wall Outlet Cable Required: Two-way RF splitter, 3 coaxial cables, right and left analog audio cables, either S-video or video cable. These are not included with the TV but are available at most electronics stores. Connect the incoming cable or antenna to IN on the RF splitter.

  • Page 25: Vcr To A Cable Box (audio & Video)

    VCR to a Cable Box (Audio & Video) Required: Two-way RF splitter, 4 coaxial cables, right and left audio cables, S-Video or composite video cable, plus component or S-Video cables and audio cables required to connect the TV to the cable box. Connect the incoming cable to IN on the RF splitter.

  • Page 26: Hdmi Device (cable Box, Satellite Receiver, Dvd Player, Or Other Device)

    HDMI Device (Cable Box, Satellite Receiver, DVD Player, or Other Device) Required: HDMI-to-HDMI cable. This is not included with � the TV. ������� � ����� Connect an HDMI cable from the TV back panel to the ������������������ �� ����������������������������������� ����� �����������������������...

  • Page 27: Dvd Player With Component Video, A/v Receiver (sound System)

    DVD Player with Component Video Component video cables and analog audio cables are required. These are not included with the TV. Connect the component video cables from Y PB PR VIDEO OUT on the back of the DVD player to the COMPONENT jacks on the TV back panel, match- ing the red, green, and blue colored connections.

  • Page 28: Older Cable Box, Camcorder

    Older Cable Box Required: 3 coaxial cables, one two-way RF splitter. These are not included with the TV. When this setup is complete, you can use the TV remote control, when programmed, to change channels on the cable box. Note: This connection is not recommended. The other connections described in this chapter provide bet- ter quality audio and video to the TV.

  • Page 29: Ieee 1394 Devices

    IEEE 1394 Devices Compatible IEEE 1394 Devices Compatible A/V devices include some, but not all, cable boxes, D-VHS VCRs, A/V discs, and future products. Some devices may have IEEE 1394 connectors but are not compatible with the TV. Areas of compatibility to consider are: 1.

  • Page 30

    IEEE 1394 Devices, continued Tips for Connecting IEEE 1394 Devices • Do not loop the last device in the chain back to the TV. When the device chain is looped, the TV may not be able to work with the other devices.

  • Page 31: Ir Emitter Netcommand® And Tv Guide On Screen

    IR Emitter NetCommand® and TV Guide On Screen An IR emitter cable is included with the TV. The NetCommand system uses emitters connected to the IR EMITTER jack to control other devices such as VCRs, DVD players, cable boxes, and satellite receiv- ers.

  • Page 32: Helpful Hints For Netcommand Connections

    Helpful Hints for NetCommand Connections Q. My VCR (or other device) does not have two sets of stereo audio outputs. How can I connect this device’s audio to both the TV and the A/V Receiver? A. You need to connect the device to the TV and then make changes to the A/V receiver setup. Connect the VCR’s audio and video to the TV;...

  • Page 33

    TV Setup Guidelines for Setting Up and Using Your New Widescreen TV When You First Power On the TV Using the TV’s Setup Menu When You First Connect a Device Initial NetCommand® Setup Additional Setup Using the NetCommand Menu ......

  • Page 34: Guidelines For Setting Up And Using Your New Widescreen Tv

    Guidelines for Setting Up and Using Your New Widescreen TV Getting Started 1. Read the section entitled “Important Information About Your TV” starting on page 6. 2. Choose a location for your TV. • Allow at least four inches of space on all sides of the TV to help prevent overheating.

  • Page 35

    Installing the Remote Control Batteries 1. Remove the remote control’s back cover by gently pressing in the tab and lifting off the cover. 2. Load the batteries, making sure the polarities (+) and (-) are correct. For best results, insert the negative (-) end first.

  • Page 36: When You First Power On The Tv, Using The Tv's Setup Menu

    When You First Power On the TV Choosing a Language for Menus When you power on the TV for the first time, you can select either English or Spanish for all menus. You can later change the language through the Setup menu. Figure 1.

  • Page 37

    Setup Menu, continued Note: • If using a CableCARD™, the complete list of available channels is provided through the CableCARD and the ANT 1 option is grayed out. • In the TV Guide On Screen® system, the chan- nels displayed and the order in which they are displayed are independent of the TV’s channel memorization.

  • Page 38

    Setup Menu, continued Set Day Select the day or days that the TV will turn on automati- to select Daily, Mon-Fri (Monday cally. Press through Friday), or individual days of the week. Press move to the Time box. Set Time With the hour highlighted in yellow characters, press repeatedly to slowly increment the hour and associated AM/PM indicator or press and hold to quickly increment...

  • Page 39: When You First Connect A Device

    When You First Connect a Device During the initial set-up process for a device, the TV will: a. detect the connected device b. prompt you to identify the device by name c. prompt you to perform NetCommand set-up for the device, if applicable d.

  • Page 40

    When You First Connect a Device, continued IEEE 1394 Connections The New 1394 Device screen appears if you connected an IEEE 1394 device. See figure 7. IEEE 1394 devices are automatically under NetCommand control. The TV can recognize up to seven IEEE 1394 devices at one time. If you connect more than one device of the same type, a unique identifier is added to the name for each one.

  • Page 41

    NetCommand Specialized Device Keys Refer to this chart when “learning” device keys. Write in functions you assign to the F1–F4 keys. Cable, Sat, Receiver DVD ‡‡ These are paired functions (e.g. Power and Power Off). When the original remote control uses a single button for both functions, learn only the first of the paired functions.

  • Page 42: Initial Netcommand® Setup

    Initial NetCommand® Setup What You Need to Know About NetCommand • NetCommand setup is optional. • NetCommand operates by sending signals from the TV to your other devices via the IR emitters, telling the devices to play, record, change inputs, adjust volume, change channels and many more functions.

  • Page 43: Additional Setup Using The Netcommand Menu

    Initial NetCommand® Setup, continued Press the keys on the TV’s remote control to highlight other keys on the list. Repeat steps 4 and 5 for each additional function you wish to control through NetCommand. 8. If the device’s remote control has keys that do not appear in the list, you can associate up to four keys with the F1 through F4 keys.

  • Page 44

    Additional Setup Using the NetCommand Menu, continued Figure 12. TV Guide On Screen setup 3. Select program sources for the listings. You can select one over-the-air source and one cable source for TV Guide On Screen. If, however, you have mul- tiple cable sources, the channel-number assignments may not match up correctly.

  • Page 45

    Additional Setup Using the NetCommand Menu, continued sound such as Dolby Digital or DTS directly to the A/V receiver, bypassing the TV entirely. A DVD player is used in this example. It is also possible for your setup to include two (or more) devices with digital surround sound connected directly to the A/V receiver.

  • Page 46

    Additional Setup Using the NetCommand Menu, continued Part 2: Learn A/V Receiver Power and Volume Keys 1. Press to highlight the check box for Power On. 2. Press ENTER on the TV’s remote control and while the text Power On is flashing, press and hold the POWER or POWER ON key on the A/V receiver’s remote control.

  • Page 47

    TV Operation and Features Remote Control ........Choosing a Program Source ChannelView™...

  • Page 48: Remote Control

    Remote Control Overview Figure 1, next page 1. Slide Switch: Selects the A/V device to be controlled by the remote control. Set the slide switch to TV for operation of the TV, NetCommand-controlled devices, and IEEE 1394 devices. Control of additional devices requires programing (see Appendix D, “Programming the Remote Control.”.

  • Page 49

    Remote Control, continued 26 27 Figure 1. Remote Control Overview Sleep Timer Setting the Sleep Timer 1. Press SLEEP on the remote control. 2. Press SLEEP additional times to increase the time in 30- minute increments up to the maximum of 120 minutes. 3.

  • Page 50: Choosing A Program Source, Channelview™ Channel Listings

    Choosing a Program Source NOTE: If your only viewing sources are connected to the ANT 1 and ANT 2 antenna jacks, you can switch inputs without the Input Selection menu. Press INPUT to switch between ANT 1 and ANT 2. To verify which is the current source while watching TV, press INFO to see the on-screen status display.

  • Page 51: Status Display

    Status Display The on-screen status display appears when you turn on the TV, change inputs, change channels, or press the INFO button on the remote control. The most common displays Analog Program 1. Source Antenna or Input 2. Analog Channel being received (If an antenna source) 3.

  • Page 52: Split Screen

    Split Screen Split Screen allows you to view pictures from two different sources at the same time. Split Screen is available when you have video sources connected to the TV in addition to connections on ANT 1 or ANT 2. Operation Split Screen Operations Turn Split Screen on or off...

  • Page 53

    Split Screen Displays 16:9 Main Picture/ 16:9 Main Picture/ 4:3 Sub-Picture 16:9 Sub-Picture 16:9 Main 4:3 Sub- 16:9 Main Picture Picture Picture ‡ ‡ 16:9 Main 4:3 Sub- 16:9 Main Picture Picture Picture 16:9 Main 4:3 Sub- 16:9 Main Picture Picture Picture Display choices.

  • Page 54: Tv Signals And Display Formats

    TV Signals and Display Formats This is a widescreen TV, also known as a 16:9 TV. This shape reflects the new types of images available from HDTV and many DVDs. There are still many older style narrow-screen images (called 4:3 aspect ratio) you will encounter.

  • Page 55

    TV Display Formats See descriptions on the preceding page. ��������������� ������������������������ ���������� �������� ���������������������������� ������������������ ������ ���������������� ������������������ ������������ ��������������������������������� ���������������������� ���� ������������������� ���������������������� ���������������������������������������� ����������������� ������� ��������������� ������������������ ������������������������������������ ������������������ ������������ ��������������� ��������������������� ������������������������������������ ������ �������� ������������������ ������������������� ����������������������������� ���������������...

  • Page 56: Memory Card Playback

    Memory Card Playback Memory Card Reader (models WD-57732, WD-65732, WD-73732) Inserting a memory card 1. Insert a card into a matching card slot on the front of the TV. Be sure to use the correct card slot. See the table below. Normally the label side should be up, but if the card does not fit, try turning the card over and insert again.

  • Page 57

    Memory Card Playback, continued will be scaled to the TV display. Some pictures may be cropped to fit. • Full path file names can be no longer than 50 char- acters and must end in a .jpg extension. Not all 50 characters will display.

  • Page 59

    TV Menu Settings 3D Graphical Main Menu ........Setup Menu .

  • Page 60

    3D Graphical Your TV has Mitsubishi’s exclusive 3D Graphical information for menu choices and changes using the TV’s remote control. Menu Screens A picture (icon) is highlighted on the menu screen when selected with the directional arrows . You may then make changes within the menu or access sub- menus, if available.

  • Page 61: Main Menu

    Main Menu Press MENU on the remote control to open the Main menu, figure 1. See below for an overview of the options available through the Main menu. Setup See chapter 3, “TV Setup,” for use of the Setup menu. Select English or Spanish for menus and on-screen displays.

  • Page 62: Setup Menu, Netcommand Menu

    Setup Menu See chapter 3, “TV Setup,” for use of the Setup menu. NetCommand Menu The features described in this section are available even if you have not performed NetCommand setup. See chapter 3, “TV Setup,” for options available for NetCommand-con- trolled devices.

  • Page 63

    NetCommand Menu, continued To Replace One Device with Another on an Input Jack 1. Disconnect the device you wish to remove from the 2. Connect the new device to the vacated jack. 3. Open the Input Name menu from the NetCommand menu.

  • Page 64: Channel Menu

    Channel Menu Settings for the Channel FAV Memory Number Shown Banks Figure 6. Channel menu Antenna (Channel Menu) Select either 1 (ANT 1 MAIN) or 2 (ANT 2 AUX) as the antenna source for the channels you wish to edit. Channel (Channel Menu) Select the affected channel number (shown in the Channel box) in any of three ways:...

  • Page 65

    Channel Menu, continued FAV (Channel Menu) The FAV feature lets you store groups of favorite channels in up to nine different FAV memory banks. For example, each household member can store favorite channels in their own bank or you can store groups of channels by content, e.g., news, sports, children’s programming, etc.

  • Page 66: Captions Menu

    Captions Menu For analog channels, broadcasters can send either stan- dard closed captions or text service. Standard closed captions follow the dialogue of the characters on screen and display in a small section of the screen. Text-service closed captions often contain information such as weather or news and cover a large portion of the screen.

  • Page 67

    Captions Menu, continued Size Select the desired font size. Large is the recommended font size. Color The available font colors are listed below. Text and back- ground cannot be set to the same color. White Yellow Black Green Magenta Cyan Blue Background You can change the background color to make the digital...

  • Page 68: Parental Lock Menu, Setting A Pass Code, Lock Tv By Time And Front-panel Lock

    Parental Lock Menu The Parental Lock menu gives you control over three different types of parental controls. You must use a pass code to open this menu to enable/disable the lock options. The three parental controls available are: Ratings (U.S. Ratings/Other Ratings) •...

  • Page 69

    Parental Lock Menu, continued U.S. Ratings Menu Use this menu to turn U.S. rating restrictions on or off and to change the permitted rating levels. TV Content Categories U.S. Restric- TV Rating and tions On/Off Supplemental Restrictions Figure 10. U.S. Ratings menu 1.

  • Page 70: Bypassing The Ratings Lock And Lock By Time

    Parental Lock Menu, continued 1. Highlight the button labelled Other Ratings on the Parental Lock menu (see figure 9) and press ENTER to open the Other Ratings menu (see figure 11). to select On or Off. 2. Press 3. If you selected On, press to move to the Rating Group box.

  • Page 71: Movie Ratings

    V-Chip Signal Information When provided by the broadcaster or program source, V-Chip ratings let you control the types of programming that can be viewed on the TV. When V-Chip ratings are supplied, they are displayed when you change the channel or press INFO on the remote control.

  • Page 72: Audio/video Menu, Audio Settings

    Audio/Video Menu Figure 12. Audio/Video Menu A/V Memory Reset A/V Memory Reset allows you to reset a specific input’s A/V settings to the original factory settings. Highlight the box and press to select the input name. Next press ENTER. The audio settings of Balance, Listen to, and Language are general TV settings unaffected by A/V Memory Reset.

  • Page 73

    Audio/Video Menu, continued • To receive the best fidelity with music programs, change this setting to Off. • When connecting to an A/V receiver, set Level Sound to Off and turn off the TV speakers to send full dynamics to the A/V receiver. Analog-Only Audio Settings You can set analog-only audio settings while viewing either analog or digital sources, but the settings affect...

  • Page 74: Video Settings

    PerfectColor screen to reset all colors to the default settings. Figure 13. Set PerfectColor adjustments independently for each TV input. ◊ PerfecTint™ (models WD-57732, WD-65732, WD-73732): Provides further color refinement using six color sliders memorized for each input. To use PerfecTint: With the PerfectColor screen displayed and with...

  • Page 75

    Audio/Video Menu, continued ◊ DeepField™ Imager (models WD-57732, WD-65732, WD-73732): When On is selected, the black levels are dynamically enhanced in portions of the screen to provide strong contrast with detail over mixed screen content. When Off is selected, the entire screen adjusts the contrast the same.

  • Page 77

    NetCommand Functions NetCommand-Controlled Devices and the Input Selection Menu NetCommand-Controlled Recording Using IEEE 1394 Devices ........... .

  • Page 78: Netcommand-controlled Devices And The Input Selection Menu

    NetCommand-Controlled Devices and the Input Selection Menu For devices under NetCommand control, the Input Selec- tion menu allows you to: • Select the device for viewing • Switch audio between the TV speakers and A/V receiver • Power compatible devices on or off •...

  • Page 79: Netcommand-controlled Recording

    NetCommand-Controlled Recording This section describes making recordings independently of the TV Guide On Screen system. For instructions on setting up recordings using TV Guide On Screen, see the separate TV Guide On Screen® Interactive Program Guide User’s Manual. Recording from the Recording Setup Menu You can schedule the recording to take place at a later time and program the recording duration for a minimum of 30 minutes and a maximum of six hours (in 30-minute...

  • Page 80

    NetCommand-Controlled Recording, continued Immediate Recording from ChannelView 1. Press INPUT to open the Input Selection menu. High- light an ANT 1 or ANT 2 program source and press ENTER. 2. Press GUIDE to open the ChannelView channel guide for the current antenna input. 3.

  • Page 81

    NetCommand-Controlled Recording, continued Record Menu: Setting Recording Defaults The Record menu allows you to set defaults for your recording devices, set up recordings, view the Record List, and cancel scheduled recordings. Highlight the Record icon on the Main menu to view the Record menu. Figure 6.

  • Page 82

    NetCommand-Controlled Recording, continued • The VCR must be set manually to “Line Input.” Display the Input Selection menu, highlight the VCR and press GUIDE to change VCR inputs. • The TV can select channels on compatible cable boxes for recordings when the cable box is under NetCommand control.

  • Page 83: Using Ieee 1394 Devices

    Using IEEE 1394 Devices IEEE 1394 Devices and the Input Selection Menu When you connect an IEEE 1394 device to the TV network and power it on, the new device is automatically detected. Some non-audio/video or incompatible IEEE 1394 devices, such as personal computers (PCs), may not be detected by the TV and do not appear in the Input Selec- tion menu.

  • Page 84

    The TV Remote Control and IEEE 1394 Devices • For compatible satellite receivers and some cable boxes, the TV remote control GUIDE key displays the on-screen programming guide for the receiver or cable and ENTER to navigate the dis- box. Press played program guide.

  • Page 85

    A/V Discs A/V Disc Track List Screen When viewing an A/V Disc: • Press GUIDE to display its Track List (see figure below). • Press to navigate through the Track List. • To play a track, select it on the list, then press ENTER. Press INFO to view details for a highlighted track, if •...

  • Page 86

    Chapter 6. NetCommand Functions Chapter 6. NetCommand Functions...

  • Page 87

    Using the TV with a Personal Computer Setup ......... . . Video Adjustments Connecting a Computer to the TV Adjusting Image Resolution...

  • Page 88: Setup

    Setup 1. See the TV specifications in Appendix B to confirm that your computer video signal is compatible with the 2. Note whether the computer supplies a digital or analog video signal. You will need this information during the setup procedure. •...

  • Page 89: Connecting A Computer To The Tv

    Connecting a Computer to the TV Computer with DVI Digital Monitor Output Required: DVI-to-DVI cable, stereo audio cables If the computer’s audio output is a single mini jack, a mini audio-to-RCA-male “Y” adapter cable is also required. Connect the DVI-to-DVI cable from the computer DVI output to the PC-DVI jack on the TV back panel.

  • Page 90

    Connecting a Computer to the TV, continued Computer with VGA 15-Pin Monitor Output (Analog Video) Required: 15-pin computer VGA-to-DVI cable or a VGA computer cable and a DVI/VGA adapter, stereo audio cable. If the computer’s audio output is a single mini jack, a mini audio-to-RCA-male “Y”...

  • Page 91: Adjusting Image Resolution

    Adjusting Image Resolution Your Mitsubishi TV can display resolutions from standard VGA (640 x 480) through 1920 x 1080 signals at a refresh rate of 60 Hz. Note that 1280 x 1024 and 1920 x 1080 signals are supported only for digital computer signals. The resolution of 1920 x 1080 is supported at refresh rates of 24, 30, and 60 Hz.

  • Page 92: Computer Display Formats

    Computer Display Formats Repeatedly press the FORMAT key to cycle through the TV displays available for your computer’s video signal. Computer Signal Format 640 X 480 WVGA 848 X 480 SVGA 800 X 600 WSVGA 1064 X 600 Format 1024 X 768 PC 720p 1280 X 720 WXGA...

  • Page 93

    Appendices Appendix A: Bypassing the Parental Lock Appendix B: Specifications Appendix C: Lamp Cartridge Replacement Appendix D: Programming the Remote Control Appendix E: Troubleshooting ....

  • Page 95: Appendix A: Bypassing The Parental Lock

    Appendix A: Bypassing the Parental Lock IMPORTANT Cut along the dotted line and file bypass instructions in a safe place for future reference. Appendices Bypassing the Parental Lock After you set the lock, you must use your pass code to view a locked program, view the locked TV, cancel the lock, or enter the Parental Lock menus.

  • Page 96

    Appendices Appendices This page intentionally left blank...

  • Page 97: Appendix B: Specifications

    Appendix B: Specifications Model Projection System WD-Y57, WD-Y65 DLP, 0.65” chip, 1920 x 1080 pixels with Smooth Picture™ WD-57732, WD-65732 DLP, 0.843” chip, 1920 x 1080 pixels with Smooth Picture™ WD-73732 Reception Channel Frequency Reception Channel Type* * Note for Digital Channels: The channel numbers displayed on screen are determined by the broadcaster or cable company and can vary from the standard frequency number.

  • Page 98

    (2 rear) Physical Characteristics and Power Consumption Model Height WD-Y57 36 3/16 WD-Y65 40 3/4 WD-57732 36 3/16 WD-65732 40 3/4 WD-73732 44 3/4 IEEE 1394 System Compatibility • This television is designed to conform to IEEE 1394 AV/C Software standards in effect at the time of development.

  • Page 99: Appendix C: Lamp Cartridge Replacement

    Visit our website at www.mitsuparts.com or call (800) 553-7278. Order a new lamp by part number as shown below. TV Model Number Lamp Part Number WD-Y57, WD-Y65, 915P049010 WD-57732, WD-65732 WD-73732 915P049020 • Do not remove the lamp cartridge immediately after turning off the television. You may get burned because the lamp is very hot.

  • Page 100

    Appendix C: Lamp Cartridge Replacement, continued WARNING THE COVER IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE THE TV WITHOUT REMOVING THE COVER COMPLETELY. Removing the Old Lamp Cartridge 1.

  • Page 101: Appendix D: Programming The Remote Control

    Appendix D: Programming the Remote Control This appendix explains how to program the TV’s remote control to operate other A/V devices. This is distinct from NetCommand “Learning.” To summarize: the TV’s remote control can be made to operate other devices by two dif- ferent methods: •...

  • Page 102

    Appendix D: Programming the Remote Control Programming the Remote Control Method 1: Code Entry Move the slide switch at the top of the remote to the position for the product you want to control. Refer to the table below. Only one of each device type can be controlled in each slide-switch position.

  • Page 103

    Appendix D: Programming the Remote Control Audio Lock: Universal A/V Receiver Control With Audio Lock active, the remote control operates the volume and mute functions of the A/V receiver in all positions of the slide switch. Activate Audio Lock if you normally use an A/V receiver with your TV and other A/V equipment.

  • Page 104

    Appendix D: Programming the Remote Control Programming Codes, continued A/V Receivers Brand Code Audiotronic 31189 Audiovox 31627, 31390 B & K 30840, 30820, 30701 Bel Canto Design 31584 30702 Bose 31253, 31229, 30639 Brix 31602 Cambridge Soundworks 31477 Capetronic 30531 Carver 31289, 31189, 30189, 30121 Coby...

  • Page 105

    Appendix D: Programming the Remote Control Programming Codes, continued CD Players Brand Code 31294, 30072 Kenwood 30826, 30681, 30626, 30190, 30037, 30028, 31711, 31373, 31372, 31318 Koss 31317 Krell 30157 31208 30157 Linn 30305 Magnavox 30305, 30157, 30038 Marantz 30626, 30435, 30180, 30157, 30038, 30029 Mark Levinson 31484...

  • Page 106

    Appendix D: Programming the Remote Control Programming Codes, continued Cable Boxes Brand Code Hamlin 10273, 10259, 10034, 10020, 10009 Hitachi 10011 Hytex 10007 i3 Micro 11602 Jasco 10315, 10153, 10015 Jerrold 10810, 10476,10276, 10024, 10015, 10014, 10012, 10011, 10003 Linsay 10440 Magnavox 10027...

  • Page 107

    Appendix D: Programming the Remote Control Programming Codes, continued DVD Players/Recorders Brand Code Curtis Mathes 21087 CyberHome 21129, 21117, 21024, 21023, 20874, 20816 Daewoo 21242, 21234, 21172, 21169, 20869, 20833, 20784, 20705 Daytek 20872 Denon 20634, 20490 Desay 21407 Disney 21270, 20675 Dual 21085, 21068...

  • Page 108

    Appendix D: Programming the Remote Control Programming Codes, continued DVD Players/Recorders Brand Code Techwood 20692 Terapin 21031 Theta Digital 20571 Toshiba 21154, 20695, 20503 Tredex 20804, 20803, 20800, 20799 Urban Concepts 20503 US Logic 20839 Venturer 20790 Vizio 21226, 21064 Vocopro 21027 Xbox...

  • Page 109

    Appendix D: Programming the Remote Control Programming Codes, continued VCRs and DVRs Brand Code 21972 Admiral 20479, 20209, 20048 Adventura 20000 Aiko 20278 Aiwa 20307, 20124, 20037, 20000 Akai 20242, 20175, 20106, 20061, 20041 Alienware 21972 America Action 20278 American High 20035 Asha 20240...

  • Page 110

    Appendix D: Programming the Remote Control Programming Codes, continued VCRs and DVRs Brand Code Optonica 20062 Orion 20479, 20295, 20209, 20184, 20002 Panasonic 21262, 21162, 21062, 20616, 20225, 20162, 20077, 20035 Penney 20240, 20054, 20042, 20040, 20038, 20037, 20035 Pentax 20105, 20042 Philco 20035...

  • Page 111: Appendix E: Troubleshooting

    Appendix E: Troubleshooting System Reset Button If the TV does not respond to the remote control, front panel controls, or will not power on/off, press the SYSTEM RESET button on the front panel with a pointed object, such as the point of a pencil or end tip of a paperclip. The green LED will flash quickly for about one minute.

  • Page 112

    Appendix E: Troubleshooting, continued General TV Operation Symptom A fan is running even while the TV is powered off. The TV remote control does not work. TV does not respond to the remote control or to front panel control and TV will not power on or off.

  • Page 113

    Appendix E: Troubleshooting, continued TV Power On/Off Symptom TV takes an excessively long time to power You cannot program the TV to turn on auto- matically (Timer function) The TV will not turn on after being plugged TV turned itself off and the light on the front panel started to blink.

  • Page 114

    Appendix E: Troubleshooting, continued Picture Symptom Screen is black when trying to view digital channels or IEEE 1394 device. 10. DVCR analog/digital problems. 11. Cannot see a picture from a DV Camcorder. Indicators Symptom Lamp indicator light is a constant red. Lamp indicator light is a flashing yellow.

  • Page 115

    Appendix E: Troubleshooting, continued IEEE 1394 Recording Symptom Program to be recorded was correctly selected from ChannelView, however, incor- rect program was recorded. Incomplete ChannelView program recorded. Recording device may lack sufficient blank space to make a full ChannelView program recording failed. Cannot record to or from the IEEE 1394 device, including dubbed recordings.

  • Page 116

    Appendix E: Troubleshooting, continued IEEE 1394 Devices Symptom There is no audio and video from the IEEE 1394 device. The IEEE 1394 Device is no longer listed in the Input Selection menu. The IEEE 1394 device cannot be selected (is grayed out).

  • Page 117

    Appendix E: Troubleshooting, continued NetCommand Symptom Cannot see the A/V Receiver menu. NetCommand unable to learn specific device keys. The A/V Receiver is the selected audio source but there is no sound. TV Guide On Screen (see the separate TV Guide On Screen® Interactive Program Guide User’s Manual for detailed information) Symptom TV Guide On Screen®...

  • Page 118: Trademark And License Information

    Trademark and License Information LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

  • Page 119: Mitsubishi Tv Software

    Mitsubishi TV Software END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.

  • Page 120: Mitsubishi Dlp™ Projection Television Limited Warranty

    This DLP Projection Television uses a single DLP chip to create the screen image. This technology creates the image using small dots, or picture elements (pixels). Your DLP Projection TV is manufactured to a high level of performance and quality, in fact, 99.99% perfect in the number of properly functioning pixels.

  • Page 121

    d. To obtain a replacement lamp during the warranty period, please contact the MDEA Consumer Relations Department at (800) 332-2119. After the warranty period you may order the lamp directly from the MDEA Parts Department at (800) 553-7278. 2. THIS LIMITED WARRANTY DOES NOT COVER: a.

  • Page 122: Index

    Index A/V Discs 85 A/V Memory Reset. See Reset A/V Receiver Adding NetCommand Control 44 Connecting 27 A/V Reset. See Reset Adjust Keys (Up/Down/Left/Right) 48, 60 Anamorphic Picture Format 81 DVD Definitions 54 Playback 81 Antenna Adjusting and the Signal Strength Meter 64 Connecting 23 Antenna Inputs (ANT 1/MAIN, ANT...

  • Page 123

    MP3 Audio 13, 14, 29, 32 and Memory Cards 57 Playback 56 Mute Audio and Closed Captions 66 and status Display 51 MUTE key 48 Video Mute 72 NetCommand® A/V Receiver Control 43 and the Input Selection Menu 78 Compared to Programming the Remote Control 101 Description 13, 42 Initial Setup 42...

  • Page 124

    For questions, call Consumer Relations at remote controls, lamp cartridges, or Owner’s Guides Visit our website at www.mitsuparts.com Demo Mode This TV has a demo mode for use in retail stores. Demo mode causes the TV to display a series of screens outlining the TV’s features.

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: