Netcommand-Controlled Recording - Mitsubishi Electric WD-57831 Owner's Manual

Mitsubishi crt television user manual
Hide thumbs Also See for WD-57831:
Table of Contents

Advertisement

NetCommand-Controlled Recording

This section describes making recordings independently
of the TV Guide On Screen system. For instructions on
setting up recordings using TV Guide On Screen, see the
separate TV Guide On Screen® Interactive Program Guide
User's Manual.
Recording from the Recording Setup Menu
You can schedule the recording to take place at a later
time and program the recording duration for a minimum
of 30 minutes and a maximum of six hours (in 30-minute
increments). The default is one hour. During the record-
ing, you can view a different device or power off the TV.
Immediate Recording from the Menu
1. Press
(RECORD) to open the Recording Setup menu.
Figure 2. The Recording Setup menu
2. Review the recording setup information. Move the
highlight to each box you need to change.
• With the leftmost icon highlighted (the source),
press
to change the source input if needed.
• Channel. If the source is an antenna, select a
memorized channel using
the channel number from the remote control and
press ENTER.
• Record To. If you have more than one recordable
device connected, use
list in the Record To box.
• Duration. Use
of from 30 minutes to six hours in 30-minute incre-
ments. The default is one hour.
3. Press
a second time to start recording.
Time-Delayed Recording from the Menu
1. Ensure that TV Energy Mode is set to Fast Power On
and the TV clock is set to the correct time and day.
Use the Setup menu to make changes.
(RECORD) to open the Recording Setup menu.
2. Press
3. Review the recording setup information. To change
the source, recording device, or duration, follow the
steps described above under "Recording Now."
4. Specify when to start the recording.
• Start Time
a. With the hour highlighted in gold characters,
press
to select the hour, including AM or
PM. Press ENTER to move the highlight to the
minutes.
, CH
/ , or enter
to select it from the
to select a recording duration
Chapter 6. NetCommand Functions
b. With the minutes highlighted, press
select the minutes.
• Day. Use
to select a day of the week.
5. Select Add and press ENTER to add the recording to
the Record List. A confirmation message will be
displayed if your selection is successful. If you pick
overlapping times, day(s), or destination devices, you
will see a message stating there is a conflict.
6. While the Recording Setup menu is displayed, press
GUIDE to display the Record List (see figure 3). In the
Record List you can view a list of scheduled record-
ings and verify the addition of the recording to the
schedule. A maximum of 32 recordings can be
scheduled.
7. From the Record List you can:
• Press CANCEL to delete a recording from the schedule.
• Press GUIDE to return to the Recording Setup menu.
• Press EXIT to return to TV viewing.
• Press MENU to return to the Main menu.
Figure 3. Record List screen. From the Record menu,
press GUIDE to open the Record List to review or cancel
scheduled recordings.
TV Guide On Screen® and the Record List
Programs scheduled through TV Guide On Screen do not
appear in the Record List. Refer to the separate TV Guide
On Screen® Interactive Program Guide User's Manual
for information regarding scheduling recordings with TV
Guide On Screen.
If there is a conflict between a recording scheduled
through TV Guide On Screen and the Record List, the TV
Guide On Screen recording takes priority.
Recording from the ChannelView™ Channel
Guide
ChannelView™ is available when TV Guide On Screen is
disabled. ChannelView provides program listings, as sent
by the broadcasters, for memorized channels on ANT 1
and ANT 2. Press the GUIDE key while watching ANT 1 or
ANT 2 to view ChannelView listings and to set up imme-
diate or future recordings as described here.
79
to

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Wd-65831Wd-73831Dlp wd-57831Dlp wd-65831Dlp wd-73831

Table of Contents