1. Manuals
  2. Brands
  3. Asko Manuals
  4. Dishwasher
  5. D5534XLFI
  6. Installation instructions manual

Asko D5534XLFI Installation Instructions Manual

Hide thumbs Also See for D5534XLFI:
Table of Contents

Advertisement

Quick Links

INSTALLATION INSTRUCTIONS
CONTENTS
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
461326 Install DW90 FI USA EN Rev 01.indd 1
FI DISHWASHER
AUTOMATIC HIGH LOOP
The drain hose is fastened to the back of
the machine at the best height. To eliminate
potential drain problems, leave this hose in
place.
2
2
3
4
4
4
5
5
5
6
7
10
11
13
15
15
16
20
2014-01-16 10:51:23

Advertisement

Table of Contents
loading

Related Manuals for Asko D5534XLFI

Summary of Contents for Asko D5534XLFI

  • Page 1: Table Of Contents

    FI DISHWASHER INSTALLATION INSTRUCTIONS AUTOMATIC HIGH LOOP The drain hose is fastened to the back of the machine at the best height. To eliminate potential drain problems, leave this hose in place. CONTENTS INTRODUCTION WHAT YOU NEED SAFETY INSTRUCTIONS XXL DISHWASHERS UNIT DIMENSIONS PREPARING THE LOCATION ADA AND XL DISHWASHERS...

  • Page 2: Introduction

    NOTE: If a dishwasher is being installed in this area for the first Cosmetic damage must be reported to the ASKO dealer time, most of the cabinet work, plumbing, and electrical within five days from the date of purchase. As soon as has to be done before you move the machine into place.

  • Page 3: Safety Instructions

    SAFETY INSTRUCTIONS • It is important that you closely follow the instructions BEFORE STARTING THE INSTALLATION: provided here. Connection to water supply: • An incorrect or defective installation can lead to • There must be a shut off valve on the water supply higher consumption of energy, water and dishwashing pipe.

  • Page 4: Xxl Dishwashers

    XXL DISHWASHERS D5524XXLFI, D5534XXLFI, D5554XXLFI, D5894XXLFI, D5894AXXLFI UNIT DIMENSIONS Technical Data U.S. Metric Electricity 120V, 60Hz, 15 amp Height (Adjustable) 33-7/8˝ to 36˝ 860 mm to 914 mm Water pressure 4.2 - 140 psi, Width 23-5/8˝ 600 mm 0.03-1.0 MPa, Depth (Includes high loop) 22-7/8˝...

  • Page 5: Ada And Xl Dishwashers

    ADA AND XL DISHWASHERS D5534ADAFI, D5524XLFI, D5534XLFI, D5538XLFI UNIT DIMENSIONS Technical Data U.S. Metric Electricity 120V, 60Hz, 15 amp Height (Adjustable)* 32-1/4˝ to 34˝ 819 mm to 864 mm Water pressure 4.2 - 140 psi, Width 23-5/8˝ 600 mm 0.03-1.0 MPa, Depth (Includes high loop) 22-7/8˝...

  • Page 6: Adafi Trim Kit Installation Options

    ADAFI TRIM KIT INSTALLATION OPTIONS ASKO XLADAFI dishwashers can be installed either with or without accessory fill strips depending on the type of installation. If the dishwasher cutout has been cut to European widths of 23-5/8˝ (600 mm), the unit won’t require fill strips.

  • Page 7: Step 1. Fitting The Dishwasher In Place

    STEP 1. FITTING THE DISHWASHER IN PLACE Be sure to remove the transport protection for the door when unpacking the dishwasher. Attach the light shielding film (packed in the document bag) to the underside of the countertop above the touch buttons. (Only certain models). The light shielding film ensures optimal button functionality.
  • Page 8 STEP 1. FITTING THE DISHWASHER IN PLACE Loosen the lock nuts on the dishwasher’s steel feet using a 5/8 inch (16 mm) open-ended wrench. Screw the lock nuts down as close to the floor as possible. 5/8" (16 mm) Adjust the front feet by turning them clockwise to raise or counterclockwise to lower the dishwasher.
  • Page 9 STEP 1. FITTING THE DISHWASHER IN PLACE 10. Lift the dishwasher a little at the front and turn the front feet to lower them. 1˝ (24 mm) 11. Check that the height of the machine corresponds to the height from the floor to the bottom edge of the counter top.

  • Page 10: Step 2. Attaching The Accessory Door Or Custom Panel

    STEP 2. ATTACHING THE ACCESSORY DOOR OR CUSTOM PANEL Follow the separate instructions supplied with the dishwasher to attach the chosen accessory door or custom panel to the front of the machine. NOTE: Once you have fitted the accessory door or custom panel to the dishwasher, the door springs may need adjusting.

  • Page 11: Step 3. Adjusting The Door Springs

    STEP 3. ADJUSTING THE DOOR SPRINGS TYPE A TYPE B (SEE PAGE 12) TYPE A The door springs are on the sides of the dishwasher. If necessary, pull out the dishwasher and adjust the tension of the door springs. A good idea is to try adjusting one side only first.
  • Page 12 STEP 3. ADJUSTING THE DOOR SPRINGS Replace the back end of the spring by holding the spring at a right angle to the side of the dishwasher and pushing the end of the spring into the hole, then turning the spring in towards the dishwasher. Reattach the front end of the spring by pulling it up and forward to fasten it in the mount.

  • Page 13: Step 4. Connecting Electricity, Water, And Drain

    CONNECT DRAIN HOSE THREE WAYS TO INSTALL DRAIN CONNECTIONS ASKO provides a 7/8˝ (22 mm) diameter corrugated drain hose which is connected to the back of the unit to form a high loop. A) Typical connection to sink plumbing before trap...
  • Page 14 STEP 4. CONNECTING ELECTRICITY, WATER, AND DRAIN 2. CONNECT WATER SUPPLY HOSE WARNING! Plumbing connections must comply with applicable sanitary, safety and plumbing codes in your area. Shutoff valve The machine can be connected to either a hot (max. 160 °F, 70 °C) or cold water supply. We recommend a cold water supply.

  • Page 15: Step 5. Checking Dishwasher Function And Fit

    STEP 5. CHECKING DISHWASHER FUNCTION AND FIT Test the dishwasher with the Rinse & Hold program. Check that the dishwasher fills and drains properly. Also check that none of the connections leak. Also check that adjacent drawers and cabinet doors can be opened when the dishwasher door is open.

  • Page 16: Step 7. Attaching The Toe Kick (If Applicable)

    STEP 6. SECURING THE DISHWASHER Check that the dishwasher’s steel feet are solidly placed on the floor. Make sure the dishwasher is not hanging in the air by the mounting tabs. If it is, turn the front feet to lower them until the machine is resting on the feet.
  • Page 17 STEP 7. ATTACHING THE TOE KICK (IF APPLICABLE) TYPE A Insulation material Insulation material 2. The toe kick is attached with two screws that can only be adjusted vertically. 3. The toe kick is attached with two screws that can only be adjusted vertically.
  • Page 18 STEP 7. ATTACHING THE TOE KICK (IF APPLICABLE) TYPE B Insulation material Insulation material Page 18 Customer Care Center 1-800-898-1879 www.askona.com 461326 Install DW90 FI USA EN Rev 01.indd 18 2014-01-16 10:51:53...
  • Page 19 STEP 7. ATTACHING THE TOE KICK (IF APPLICABLE) Page 19 Customer Care Center 1-800-898-1879 www.askona.com 461326 Install DW90 FI USA EN Rev 01.indd 19 2014-01-16 10:51:54...

  • Page 20: Installation Checklist

    INSTALLATION CHECKLIST ASKO - DISHWASHER Appliance Installation Checklist • Remove packaging and check for cosmetic damages. • Remove the information packets from inside the dishwasher. • Attach any accessories as required by the installation. Fill strips, light shielding film, supplied door sealing, accessory door, custom panel...

Table of Contents