Mesa/Boogie MARK 1 RE-ISSUE Owner's Manual page 15

DIAGNOSING PRE AMP TUBE PROBLEMS:
Because your amplifier is an all tube design, it is quite possible that you will at some point experience minor pre-amp tube noise. Rest
assured - this is no cause for alarm and you can take care of the problem yourself in a matter of minutes by simply swapping tubes
Let us begin by saying; It is a "very good" idea to keep at least a couple of spare pre-amp tubes on hand at all times to insure
uninterrupted performance. These minor pre-amp tube problems can take many forms but can generally be described in two catego-
ries: Noise and Microphonics, Noise can be in the form of crackling, sputtering, white noise/hiss and/or hum. Microphonic problems
usually appear in the form of a ringing or high pitched squealing that gets worse as the gain or volume is increased thus are more
noticeable in the higher gain Lead modes. Microphonic problems are easily identified because the problem is still present even with
the instruments' volume off or unplugged altogether - unlike pick-up feedback which ceases as the instrument is turned down. Micro-
phonic noise is caused by mechanical vibration and shock: think of banging a microphone around and you'll understand where the
word came from.
The best way to approach a pre-amp tube problem is to see if it occurs only in one specific mode or channel. Then refer to the Tube
Task Chart found on page page 8 and it should lead you to the tube needing replacement. Then all that remains is to swap the suspect
tube for a known good performer.
If you cannot narrow down the trouble to a specific mode or channel, the problem may be the small tube that drives the power tubes
which is operational in all modes and channels. Though rare, a problem with the driver tube would show up in all aspects of perfor-
mance - so if you can't narrow the problem down to being mode or channel specific, you may want to try replacing the driver tube
Driver problems generally show themselves in the form of crackling or hum in all modes of performance and/or weak overall output
from the amplifier. Occasionally an anemic driver tube will cause the amplifier to sound flat and lifeless, but this is somewhat
uncommon, as worn power tubes are a more likely suspect for this type of problem.
Sometimes making the diagnosis is more trouble than it's worth and it's faster and easier to merely replace the small preamp tubes
ONE AT A TIME with a replacement known to be good. But MAKE SURE you keep returning the tubes to their original socket until you
hit the one that cures the problem. You'll notice that tubes located nearer to the Input jack always sound noisier...but this is because
they are at the start of the chain and their noise gets amplified over and over by the tubes that follow. The tube that goes into this
"input socket" (usually labled V1) needs to be the least noisy of the bunch. The tube that goes at the end of the preamp chain - just
ahead of the power tubes - can be quite noisy without causing any problem at all. The tubes in your amp have already been located
in the most appropriate sockets and this is why you should NEVER pull them all out at once and ALWAYS swap them one at a time
ALWAYS return a perfectly good tube to its original socket. Also it's a good idea to put the amp on Standby when swapping tubes to
reduce the heat build up in the tubes themselves and to prevent explosive noises (which can still occur even if you are pulling the
tubes away from their sockets gently) from coming through the speaker.
Remember, take your time, be patient and chances are real good that you can fix your amp yourself by finding and replacing the bad
tube. It kills us to see someone who has shipped their amp back to us...and all it needed was a simple tube replacement! If you must
send back your amp, unplug the power cord, speaker and reverb cables then remove the chassis from the cabinet by unscrewing the
four mounting bolts on top. The chassis then slides back like a drawer and comes out. Remove the big power tubes and mark them
according to their location from left to right 1, 2 etc. They need to be wrapped separately with plenty of wadded up newspaper around
them and put in a smaller box within the larger carton. To wrap the chassis, use plenty of tightly wadded up newspaper so there is at
least six inches of "crush space" between the chassis and the cardboard box. Bubble wrap also works well but please DON'T use
styrene peanuts - they will shift during transit and get lodged inside your electronics as well as allowing your amp to end up at the
bottom of the box unprotected and possibly damaged. Preamp tubes don't normally wear out as a rule. Therefore, it is not a good idea
to change them just for the sake of changing them. If there isn't a problem - don't fix it. If there is no result from your substitutions, it
may be possible that you have more than one problematic tube. Though rare, this does happen and though it makes the troubleshoot-
ing process a little more intimidating, it is still possible to cure the problem yourself.
NOTE: It is normal to hear a slight metallic ringing sound when tapping on the preamp tubes. As long as the tube does not break into
oscillation or start crackling or any other form of bizzare noise, it is considered normal and functional.
PAGE 11