Memorex MVD2045 User Manual

MENU SYSTEM
TO ACCESS THE MAIN MENUS:
The setup menu lets you customize the DVD player by allowing you to select various
language preferences, set up a parental level, turn captions and screen saver on and off,
adjust what type of television screen you have and more.
Below, find the menu, and then find the corresponding page that describes the features of the
selected menu option.
Enter the SETUP MENU by pressing the SETUP button. Use the Navigation (√,®,π,†)
buttons to navigate through the menus/screens and press the ENTER/PLAY ® button to
select the highlighted option.
To Exit the SETUP MENU, press the SETUP button.
GENERAL SETUP
TV DISPLAY: Your can choose a display that affects how a disc's content appears on your TV
screen.
Normal/PS (4:3 Standard): reproduces a 4:3 picture with some distortion.
Normal/LB (4:3 Letterbox): gives best reproduction of pictures recorded in this format (i.e.,
with horizontal bands at the top and button of the screen)
Wide (16:9 Widescreen): reproduces 16:9 format films in full,
on a 16:9 screen.
- - General Setup Page - -
TV Display
Angle Mark
ANGLE MARK: Select ON to turn the angle marks on and OFF OSD Lang
Screen Saver
to turn them off. Anglemarks are not available on all DVDs. HDMI Setup
HDMI Audio
Set TV Display Mode
OSD LANGUAGE: Select the desired language for the On-
Screen display to display text. The DVD must have the language included in order to display it.
SCREEN SAVER: When this option is set to ON, the screen saver will come on when the unit
stops or the image is paused for approximately one minute.
When this option is OFF, the screen saver will not come on.
HDMI SETUP: Select the output resolution to correspond with your TV (480i, 480p, 720p
(60Hz), 1080i (60Hz) or 1080p (60Hz). Refer to your TV's owner's manual for resolution. The
setting can also be changed by pressing the HDMI/PS button.
Note: If the TV screen is blank, press the HDMI/PS button repeatedly until the picture
appears on the screen again.
HDMI AUDIO: Select the desired audio format:
SPDIF: No signal output for the coaxial output port.
PCM: Select to hear the Digital Output in PCM format.
SPEAKER SETUP
DOWNMIX:
- - Speaker Setup Page - -
LT/RT: Select to hear the sound in theatrical downmix mode.
Downmix
STEREO: Select to hear the sound in Stereo downmix mode.
DOLBY DIGITAL SETUP
Set Downmix Mode
DYNAMIC: Use to slider to set the Dynamic Range. Set to OFF
to turn Dynamic Range Off.
- - Dolby Setup Page - -
Dynamic
PREFERENCE SETUP
AUDIO: Select the language the DVD will be played back in
(ENGLISH, FRENCH, SPANISH, GERMAN, JAPANESE). The
DVD must be recorded in the selected language, otherwise the
Dynamic Range Compression
default language of the DVD will be played.
SUBTITLE: Select the language the Subtitle (OSD) will be in
- - Preference Page - -
(ENGLISH, FRENCH, SPANISH, GERMAN, JAPANESE, OFF). Audio
Subtitle
The DVD must be recorded in the selected language, otherwise Disc Menu
Password
Default
the default language of the DVD will be shown.
Preferred Audio Language
DISC MENU: Select the language the DISC MENU will be in
(ENGLISH, FRENCH, SPANISH, GERMAN, JAPANESE). The DVD's DISC MENU must be
made in the selected language, otherwise the default language of the DVD will be shown.
PASSWORD
Select this option for password changing. Input your old password (the default password is
1234), then input the new password. Confirm the new password using the Number buttons,
then press the ENTER/PLAY button again. The desired new password will then be set; be sure
to write it down for future reference.
Select this option to change the TVG ® password. You must know the old password in order to
change it. If you have forgotten the password, call customer service at the number listed on the
Warranty.
DEFAULT: Select this option to reset all the preferences (except PASSWORD) to their original
factory settings. This is useful to reset the NTSC System.
TV GUARDIAN
This menu is protected by a password (the default password is 1234). The password can
changed in PREFERENCE MENU. TV Guardian (TVG) filters out objectionable language by
monitoring the closed captioning (CC) information contained on the DVD. When TVG® detects
objectionable words or phrases, it
mutes the audio and displays more appropriate "profanity free" phrases. It also offers various
levels of filtering and is easily adjustable with simple on-screen menus.
TO ACTIVATE:
1. Power on the unit, and the following dialog will appear, "Start using your TVGuardian foul
language filter today! Press the SETUP button and select TVGuardian to enable filter. This
Message will be displayed five times."
2. Press SETUP, move the cursor to the tab "TVG" and press ENTER button. A dialog and
display registration key appears. You can access the TVG Menu after entering the correct
Activation Code.
To activate the TVGuardian® feature, either go to www.TVGuardian.com or call (866-884-
3458). Please have your "Registration Key" ready.
Activation
Once you have obtained your Activation Code, please use your remote control to enter the
activation code. Once activated, you may use TVGuardian® for the life of your product.
TV GUARDIAN (CONTINUED)
TVGuardian ® Setup
1. Activate the TVGuardian ® function as described and enter the TV Guardian menu as described
above.
2. Select OFF, TOLERANT, MODERATE, STRICT using the Navigation (π,†) buttons.
NOTE If you select OFF, you will not able to select or activate the HELL/DAMN, RELIGIOUS,
SEXUAL, CC MODE settings.
3. While in the TVGUARDIAN main menu, select HELL/DAMN, RELIGIOUS, SEXUAL using the
Navigation (π,†) buttons. Press the ENTER/PLAY ® button to select Flt (Filter) or OFF (select
Filter to activate the function).
4. While in the TVGUARDIAN main menu, select CC MODE using the Navigation (π,†) buttons,
then push the ENTER/PLAY ® button to enter the CC MODE menu. Select OFF, ON MUTE or ON
CONTINUOUS as desired Navigation (π,†) buttons. Press the ENTER/PLAY ® button to confirm
the selection.
NOTE: To exit the setup; press the SETUP button until the Setup menu disappears from the screen.
TVGuardian Mode
®
Off ..............................................................................................................................No filtering
Tolerant.................................................................Filters only the most offensive foul language
TVG
Dolby
Moderate...................................................................Increased standards for language filtering
PS Normal/PS
Strict .........................................................................Filters out all common offensive language
ON Normal/LB
ENG Wide
ON
Word Subset Filtering
PCM
In addition to the main TVGuardian Modes listed above, you can turn certain word subsets on
®
or off according to your preferences.
Damn and Hell ..........................................................Filters out variations of "Damn" and "Hell"
Religious Filters out references to deity. (To watch religious programming, turn this word subset off.)
Sexual .....................................................................................Filters sexually explicit language
CC Mode
On Mute (Default) ...............Captions are displayed when offensive language is being filtered
On Always ............................................................................Captions are displayed continually
Off.................................................................................................Captions are never displayed
CC Channel
To use the TVG captioning features while watching a DVD Movie, your television must be
®
capable of displaying closed captions. Make sure that your TV CC is set to "CC1" or "CC2"
(Close caption on channel 1 or 2), and that the CC channel on your DVD player is set to "CC1"
or "CC2"respectively (CC2 is the default setting.)
SETUP HELP
Select this option and press the ENTER/PLAY button to enter the TVG's Setup Help Menu to
TVG
Dolby
find more information on TV Channel Selection and the TVG Web site address. Press the
LT/RT
ENTER/PLAY button to exit this option.
Stereo
SPECIFICATIONS
Power Requirements .............................................................................................AC120V, 60Hz
TVG Power Consumption .........................<15W (approx. 5W when set to Standby mode by remote)
Dolby
Weight ...............................................................................................................................2.5 Lbs
FULL
Dimensions ..................................................................................17 (L) x 9 (W) x 1.7 (H) inches
3/4
1/2
Weight and dimensions are approximate.
1/4
OFF
Signal System..............................................................................................................NTSC/PAL
Operating Temperature ............................................................................................+5° to +35°C
Operating Humidity Range ............................................................5% to 90% (no condensation)
TVG
Dolby
Discs Played:
ENG English
DVD-VIDEO Disc
ENG French
ENG Spanish
.....................................................................................................12cm single-sided, single layer
German
Japanese
.......................................................................................................12cm single-sided, dual layer
...................................................................................................12cm double-sided, single layer
.......................................................................................................8cm single-sided, single layer
.........................................................................................................8cm single-sided, dual layer
.....................................................................................................8cm double-sided, single layer
COMPACT DISC (VIDEO CD)
......................................................................................................................................12cm disc
........................................................................................................................................8cm disc
Video Output Level ..............................................................................................................1Vp-p
Audio Output Level ........................................................................................2Vrms (1KHz, 0dB)
Audio Signal Output Characteristics:
Frequency Responses:
DVD (Linear Audio) .........................................................20Hz-20KHz (48KHz/96KHz sampling)
CD Audio...................................................................................................................20Hz-20KHz
S/N Ratio ..............................................................................................................................70dB
Wow and Flutter.....................................................................................Below Measurable Level
Pickup:
Wavelength ........................................................................................................................655nm
Laser Power ......................................................................................................................Class 1
Specifications are subject to change without notice.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT OUR WEBSITE AT
WWW.MEMOREXELECTRONICS.COM OR CONTACT CUSTOMER SERVICE AT (954) 660-7100
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU NEED TO
RETURN THIS PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX.
FOR CONSUMER REPLACEABLE PART(S), SEE PART NUMBER(S) ON THE LOCATION OF
CONTROLS, PAGE 2, AND THEN CONTACT FOX INTERNATIONAL AT 1-800-321-6993
Memcorp, inc.
Weston, FL
Printed in Hong Kong
Visit our website at www.memorexelectronics.com
4

DVD Player

User's Guide
MVD2045
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL. This Caution Marking and Rating Label are
located at the rear and bottom enclosure of the unit.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of uninsulated dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
CAUTION:
THIS DIGITAL VIDEO DISC PLAYER EMPLOYS A
LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT,
FCC NOTICE:
PLEASE READ THIS OWNER'S MANUAL
This equipment complies with Class B digital device
CAREFULLY AND RETAIN FOR FUTURE
regulations. This equipment has been tested and found
REFERENCE. SHOULD THE UNIT REQUIRE
to comply with the limits for a Class B digital device,
MAINTENANCE, CONTACT AN AUTHORIZED
pursuant to part 15 of the FCC Rules. These limits are
SERVICE LOCATION–SEE SERVICE PROCEDURE. designed to provide reasonable protection against
USE OF CONTROLS, ADJUSTMENTS OR THE harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
PERFORMANCE OF PROCEDURES OTHER THAN
frequency energy and, if not installed and used in
THOSE SPECIFIED HEREIN MAY RESULT IN
accordance with the instructions, may cause harmful
HAZARDOUS RADIATION EXPOSURE.
interference to radio communications.
TO PREVENT DIRECT EXPOSURE TO LASER
However, there is no guarantee that interference will
BEAM, DO NOT TRY TO OPEN THE ENCLOSURE.
not occur in a particular installation. If this equipment
VISIBLE LASER RADIATION MAY BE PRESENT
does cause harmful interference to radio or television
WHEN THE ENCLOSURE IS OPENED. DO NOT
reception, which can be determined by turning the
STARE INTO BEAM.
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
WARNING: TO REDUCE THE RISK OF FIRE OR
measures:
ELECTRIC SHOCK, DO NOT EXPOSE THIS • Reorient or relocate the receiving antenna.
PRODUCT TO RAIN OR MOISTURE. • Increase the separation between the equipment and
• Connect the equipment into an outlet on a circuit
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, AND ANNOYING
INTERFERENCE, USE THE RECOMMENDED
• Consult the dealer or an experienced radio/TV
ACCESSORIES ONLY.
FCC CAUTION:
ATTENTION: POUR ÉVITER LES CHOC
To assure continued compliance, follow the attached
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
installation instructions and use only shielded cables
LARGE DE LA FICHE DANS LA BORNE
when connecting to other devices. Also, any changes
CORRESPONDANTE DE LA PRISES ET
or modifications not expressly approved by the party
POUSSER JUSQU'AU FOND.
responsible for compliance could void the user's
authority to operate the equipment.
SURGE PROTECTORS:
Manufactured under license from Dolby
It is recommended to use a surge protector for AC
Laboratories.
connection. Lightning and power surges ARE NOT
"Dolby" and the double-D symbol are trademarks of
covered under warranty for this product.
Dolby Laboratories.
This Class B digital apparatus complies with
LASER WARNING:
Canadian ICES-003.
This unit employs a laser. Only qualified service
Cet appareil numérique de la classe B est
personnel should attempt to service this device due
conforme à la norme NMB-003 du Canada.
to possible eye injury.
Before using the unit, be sure to read all operating 8A. An appliance and cart combination should
instructions carefully. Please note that these are general
precautions and may not pertain to your unit. For example,
this unit may not have the capability to be connected to an
outdoor antenna.
1. READ INSTRUCTIONS 9.
All the safety and operating instructions should be read
before the product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for
future reference.
3. HEED WARNINGS
All warnings on the product and in the operating instructions
should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this product from the wall outlet before cleaning. Do 10. POWER SOURCES
not use liquid cleaners or aerosol cleaners. Use a dry cloth
for cleaning.
6. ATTACHMENTS
Do not use attachments not recommended by the product's
manufacturer as they may cause hazards.
7. WATER AND MOISTURE
Do not use this product near water–for example: near a 11.GROUNDING OR POLARIZATION
bathtub, washbowl, kitchen sink or laundry tub; in a wet
basement; or near a swimming pool.
8. ACCESSORIES
Do not place this product on an unstable cart, stand, tripod,
bracket or table. The product may fall, causing serious injury
and serious damage to the product. Use only with a cart,
stand, tripod, bracket or table recommended by the
manufacturer or sold with the product. Any mounting of the 12. POWER-CORD PROTECTION
product should follow the manufacturer's instructions, and
152-06510-0320
should use a mounting accessory recommended by the
manufacturer.
convenience receptacles, and the point where they exit from
the appliance.
13. LIGHTNING
To protect your product from a lightning storm, or when it is
left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to
lightning and power-line surges.
14. POWER LINES
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines
or circuits as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords as this can
result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or
spray any type of liquid on the product.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna is connected to the product, be sure
the antenna system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Section 810 of the National Electric Code, ANSI/NFPA 70,
provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge product, size of grounding
conductors, location of antenna discharge product,
connection to grounding electrodes and requirements for
grounding electrodes.
18. SERVICING
Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service
technician uses replacement parts specified by the
manufacturer or those that have the same characteristics as
the original part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
NOTES ON HANDLING:
• When shipping the DVD player, always use the
The symbol for class II
original shipping carton and packing materials.
(Double Insulation)
For maximum protection, repack the unit as it
was originally packed at the factory.
• Do not use volatile liquids, such as insect spray,
near the DVD player. Do not leave rubber or
plastic products in contact with the DVD player
for a long time. They will leave marks on the
finish.
• The top and rear panels of the DVD player may
become warm after a long period of use. This is
normal and not a malfunction.
• When the DVD player is not in use, be sure to
remove the disc and turn off the power.
• If you do not use the DVD player for a long
period, the unit may not function properly in the
future. Turn on and use the DVD player
occasionally.
NOTES ON CLEANING:
Use a soft, dry cloth for cleaning.
• For stubborn dirt, soak the cloth in a weak
receiver. detergent solution, wring well and wipe. Use a
dry cloth to wipe it dry. Do not use any type of
different from that to which the receiver is
solvent, such as thinner and benzene, as they
connected.
may damage the surface of the DVD player.
• If you use a chemical-saturated cloth to clean
technician for help.
the unit, follow that product's instructions.
Warning: Cleaning and adjustment of lenses
and/or other components of playback
mechanism should be performed by a qualified
service technician.
NOTE ON LOCATING THE DVD PLAYER:
When you place this DVD player near a TV, radio
or VCR, the playback picture may become poor
and the sound may be distorted. In this case,
move the DVD player away from the TV, radio or
VCR.
be moved with care. Quick stops,
excessive force and uneven surfaces may
Insert the AC plug (with the 2 blades) into a conveniently located AC
cause the appliance and cart combination
outlet having 120V, 60Hz.
to overturn.
VENTILATION
NOTE: The AC plug supplied with the unit is polarized to help minimize
Slots and openings in the cabinet and in
the possibility of electric shock. If the AC plug does not fit into a
the back or bottom are provided for
ventilation, to ensure reliable operation of the product and to nonpolarized AC outlet, do not file or cut the wide blade. It is the user's
protect it from overheating. These openings must not be responsibility to have an electrician replace the obsolete outlet.
blocked or covered. The openings should never be blocked
by placing the product on a bed, sofa, rug or other similar
surface. This product should never be placed near or over a
radiator or heat source. This product should not be placed in
a built-in installation such as a bookcase or rack unless
EFFECTIVE DISTANCE OF THE REMOTE CONTROL TRANSMITTER
proper ventilation is provided or the manufacturer's
instructions have been adhered to.
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your
appliance dealer or local power company. For products
intended to operate from battery power, or other sources,
refer to the operating instructions.
This product is equipped with a polarized alternating-current
line plug (a plug having one blade wider than the other). This
plug will fit into the power outlet only one way. This is a
safety feature. If you are unable to insert the plug fully into
the outlet, try reversing the plug. If the plug should still fail to
fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
1
21. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. DAMAGE REQUIRING SERVICE
Unplug the product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as an adjustment of
other controls may result in damage and will often require
extensive work by a qualified technician to
restore the product to its normal operation.
e. If the product has been dropped or the cabinet
has been damaged.
f. When the product exhibits a distinct change in
performance–this indicates a need for service.
23. HEAT
The product should be situated away from heat sources
such as radiators, heat registers, stoves or other products
(including amplifiers) that produce heat.
24. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
PRECAUTIONS
NOTES ON MOISTURE CONDENSATION:
Moisture condensation damages the DVD
player. Please read the following carefully.
• Moisture condensation occurs, for example,
when you pour a cold drink into a glass on a
warm day. Drops of water form on the outside of
the glass. In the same way, moisture may
condense on the optical pick-up lens inside this
unit, one of the most crucial internal parts of the
DVD player.
Moisture condensation occurs during the
following cases:
• When you bring the DVD player directly from a
cold place to a warm place.
• When you use the DVD player in a room where
you just turned on the heater, or a place where
the cold wind from the air conditioner directly hits
the unit.
• In summer, when you use the DVD player in a
hot and humid place just after you moved the
unit from an air conditioned room.
• When you use the DVD player in a humid place.
Do not use the DVD player when moisture
condensation may occur.
• If you use the DVD player in such a situation, it
may damage discs and internal parts. Remove
the disc, connect the power cord of the DVD
player to the wall outlet, turn on the DVD player
and leave it "ON" for two or three hours. After two
or three hours, the DVD player will have warmed
up and evaporated any moisture. Keep the DVD
player connected to the wall outlet and moisture
condensation will seldom occur.
TO OBTAIN A CLEAR PICTURE:
The DVD player is a high technology, precision
device. If the optical pick-up lens and disc drive
parts are dirty or worn down, the picture quality
becomes poor. To obtain a clear picture, we
recommend regular inspection and maintenance
(cleaning or parts replacement) every 1,000 hours
of use depending on the operating environment.
For details, contact your nearest dealer.
POWER SOURCE
AC Outlet
AC Plug
NOTES:
• When there is an obstacle
between the DVD and the
transmitter, the transmitter
may not operate.
• When direct sunlight, an
incandescent lamp,
fluorescent lamp or any
20ft
other strong light shines on
the REMOTE SENSOR of
45 45
the DVD, the remote
operation may be unstable.