Page of 88
Download Bookmark Comment

MB QUART PAB 1200.1 D Installation And Operation Manual Page 4

Mb quart amplifier installation & operation.
AMPLIFIER FEATURE DESCRIPTION
Premium Multi-Channel Amplifiers
- Each model is capable of 4 & 2 ohms stereo per channel, or 4
ohms mono bridged operation.
- Tri-Mode operation with any stereo pair of amplifier channels is
possible, as with all bridgeable amplifiers.
- The input sensitivities for rated output powers are variable from
0.2 volt to 6 volt.
- All crossovers are fully variable in their respective ranges.
- Crossover filter slopes are 12 dB/octave for stereo filters, and 24
dB/octave for mono filters.
- A POWER LED indicates the powered "up" and turned "on" condi-
tion.
PAB 2100 2-Channel Amplifi er
The X-OVER slide switch selects the internal crossover functions:
- The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying daisy chaining of amplifier.
- HP: Selects the built in HIGH PASS filter, variable from 10 Hz to 150 Hz.
- FULL: Bypasses all crossovers for full frequency range operation.
- LP: Selects the built in LOW PASS filter, variable from 30 Hz to 150 Hz.
Note that the LOW PASS signal is MONO.
- In the LP position, the HIGH PASS filter acts as a subsonic filter.
- When the LP mode is selected, a 0 to +9 dB, at 45 Hz, BASS EQ is also switched
PAB 4100 4-Channel Amplifi er
INPUT MODE slide switch:
- In the CH2 position, ALL four amplifier inputs are selected from the
CH1/CH2 RCA jacks.
- In the 4CH position, channel pair 1&2 receive input signal from
RCA jacks CH1 and CH2, and channel pair 3&4 receive input signal
from RCA jacks CH3 and CH4.
The AMPLIFIER CH 1/2CH X-OVER slide switch selects the input
signal for channel pair 1&2:
- HP: Selects the built in HIGH PASS filter, variable from 10 Hz to
150 Hz.
- FULL: Bypasses all crossovers for full frequency range operation.
- BP: Selects the built in LOW PASS filter, variable from 30 Hz to
150 Hz.
Note that the LOW PASS signal is MONO.
- In the BP position, the HIGH PASS filter acts as a subsonic filter.
- When the BP mode is selected, a 0 to +9 dB, at 45 Hz, BASS EQ is
also switched in.
4
- All MB QUART Premium amplifiers feature a comprehensive dia-
gnostic system, with speaker lead short circuit, and amplifier DC
faults indicated by the DIAGNOSTIC, or PROTECT LED.
CAUTION:
DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IM-
PEDANCE. YOU WILL CAUSE DAMAGE TO THE AMPLIFIER THAT
WILL NOT BE COVERED UNDER THE WARRANTY PRINTED IN THE
BACK OF THE MANUAL.
Multi-Channel amps: 4 & 2 ohms stereo, 4 ohms mono bridged
MBQR-1
MBQR-1
The AMPLIFIER CH 3/CH 4 X-OVER slide switch selects the input
signal for channel pair 3&4:
- Hi: Selects the built in HIGH PASS filter, variable from 10 Hz to
150 Hz.
- FULL: Bypasses all crossovers for full frequency range operation.
- BP: Selects the built in LOW PASS filter, variable from 30 Hz to
150 Hz.
Note that the LOW PASS signal is MONO.
- In the BP position, the HIGH PASS filter acts as a subsonic filter.
- When the BP mode is selected, a 0 to +9 dB, at 45 Hz, BASS EQ is
also switched in.
- Full range signal from channels 1/2 inputs are routed to the Line
OUT RCA jacks, regardless of the setting of the X-OVER switches.
- The REMOTE jack enables dash mount level control of the LOW
PASS signal, CH3/4 only.

   Related Manuals for MB QUART PAB 1200.1 D

   Related Products for MB QUART PAB 1200.1 D

This manual also for:

Pab 2100c

Comments to this Manuals

Symbols: 0
Latest comments: